Search

Waste printed circuit boards (WPCBs) are resource-rich but hazardous, demanding innovative strategies for post-consumer collection, recycling, and mining for economically precious constituents. A novel technology for disassembling electronic components from WPCBs is proposed, using hot air to melt solders and to separate the components and base boards. An automatic heated-air disassembling equipment was designed to operate at a heating source temperature at a maximum of 260 °C and an inlet pressure of 0.5 MPa. A total of 13 individual WPCBs were subjected to disassembling tests at different preheat temperatures in increments of 20 °C between 80 and 160 °C, heating source temperatures ranging from 220 to 300 °C in increments of 20 °C, and incubation periods of 1, 2, 4, 6, or 8 min. For each experimental treatment, the disassembly efficiency was calculated as the ratio of electronic components released from the board to the total number of its original components. The optimal preheat temperature, heating source temperature, and incubation period to disassemble intact components were 120 °C, 260 °C, and 2 min, respectively. The disassembly rate of small surface mount components (side length ≤ 3 mm) was 40-50% lower than that of other surface mount components and pin through hole components. On the basis of these results, a reproducible and sustainable industrial ecological protocol using steam produced by industrial exhaust heat coupled to electronic-waste recycling is proposed, providing an efficient, promising, and green method for both electronic component recovery and industrial exhaust heat reutilization.

Over the last decade, there has been much effort to promote the management of e-waste in China. Policies have been affected to prohibit imports and to control pollution. Research has been conducted in laboratories and on large-scale industrial operations. A subsidy system to support sound e-waste recycling has been put in place. However, the handling of e-waste is still a concern in China and the issue remains unresolved. There has been relatively little work to follow up this issue or to interpret continuing problems from the perspective of sustainable development. This paper first provides a brief overview of conventional and emerging environmental pollution in Chinese 'famous' e-waste dismantling areas, including Guiyu in Guangdong and Wenling in Zhejiang. Environmentalists have repeatedly proven that these areas are significantly polluted. Importing and backyard recycling are decreasing but are ongoing. Most importantly, no work is being done to treat or remediate the contaminated environmental media. The situation is exacerbated by the rising tide of e-waste generated by domestic update of various electronics. This study, therefore, employs a Sales Obsolescence Model approach to predict the generation of e-waste. When accounting for weight, approximately 8 million tons of e-waste will be generated domestically in 2015, of which around 50 % is ferrous metals, followed by miscellaneous plastic (30 %), copper metal and cables (8 %), aluminum (5 %), and others (7 %). Of this, 3.6 % will come from scrap PCBs and 0.2 % from lead CRT glass. While more and more end-of-life electronics have been collected and treated by formal or licensed recyclers in China in terms of our analysis, many of them only have dismantling and separation activities. Hazardous e-wastes, including those from PCBs, CRT glass, and brominated flame retardant (BFR) plastics, have become problematic and probably flow to small or backyard recyclers without environmentally sound management. Traditional technologies are still being used to recover precious metals-such as cyanide method of gold hydrometallurgy-from e-waste. While recovery rates of precious metals from e-waste are above 50 %, it has encountered some challenges from environmental considerations. Worse, many critical metals contained in e-waste are lost because the recovery rates are less than 1 %. On the other hand, this implies that there is opportunity to develop the urban mine of the critical metals from e-waste. [ABSTRACT FROM AUTHOR]

A liquid-gas two-phase computational fluid dynamics (CFD) model was developed to simulate flow field and gas hold-up in a pilot-scale oxidation ditch (OD). The volume of fluid (VOF) model and the mass flow inlet boundary condition for gas injection were introduced in this model. The simulated values of the flow velocities and the gas hold-up were verified by experimental measurements in the pilot-scale OD. The results showed that the gas hold-up at test-site 3, immediately downstream of the surface aerator, was the highest among all three test-sites. Most of the gas existed in the upper portion of the ditch and was close to the inner side of the channel. Based on the liquid-gas two-phase CFD model, three operating conditions with different setting height ratios of the submerged impellers were simulated. The simulated results suggested that the setting heights of the submerged impellers have significant impacts on the flow velocity distribution. Lowering the setting height could increase the flow velocity in the pilot-scale OD. An optimal setting height ratio of 0.273 was proposed, which would be beneficial for minimizing sludge sedimentation, especially near the inner side of the curve bend.