Search

A secondary standard for ambient dose equivalent, H *(10), is necessary for the dissemination of the unit Sievert (Sv), but there is no such standard commercially available currently. Furthermore, the measurement of H *(10) instead of calculating H *(10) from air kerma and conversion coefficients is needed for unknown radiation fields. We developed a prototype of a new secondary standard for H *(10) based on a spherical 1 l ionization chamber for air kerma. This chamber was modified with copper wires at the inner surface to adjust the response of the chamber according to H *(10). Additionally, a Makrolon shell and an aluminium coating were added to optimize the response at energies below 50 keV. The prototype fulfils the requirements given in ISO 4037-2 in the energy range from 12 keV to 7 MeV. In combination with an electrometer, it can be used as area dosemeter, suitable for pulsed fields and for low energy radiation. [ABSTRACT FROM AUTHOR]

Medical staff in interventional procedures are among the professionals with the highest occupational doses. Active personal dosemeters (APDs) can help in optimizing the exposure during interventional procedures. However, there can be problems when using APDs during interventional procedures, due to the specific energy and angular distribution of the radiation field and because of the pulsed nature of the radiation. Many parameters like the type of interventional procedure, personal habits and working techniques, protection tools used and X-ray field characteristics influence the occupational exposure and the scattered radiation around the patient. In this paper, we compare the results from three types of APDs with a passive personal dosimetry system while being used in real clinical environment by the interventional staff. The results show that there is a large spread in the ratios of the passive and active devices. [ABSTRACT FROM AUTHOR]

In high-energy photon reference fields the value of the air kerma rate is determined by using ionization chambers (ICs). From the charge collected inside the IC the dose can be calculated using a set of calibration and correction factors according to ISO 4037-2. A crucial parameter is the correction for the attenuation and scattering of the primary radiation due to the chamber wall. This parameter can be determined using Monte Carlo calculations. The evaluation of the factor was performed for a commercially available IC of the type Victoreen 550-3 under different build-up conditions. The results were verified by measurements in the R-F high-energy photon fields according to ISO 4037-1 at the Physikalisch-Technische Bundesanstalt (PTB) and the Japan Atomic Energy Agency (JAEA). [ABSTRACT FROM AUTHOR]

A comparison has been conducted between the 6 MeV and 7 MeV (R-F) high-energy photon reference fields of the Physikalisch-Technische Bundesanstalt (PTB) and the Japan Atomic Energy Agency (JAEA). Both fields are set up according to ISO 4037. The results of both participants are in agreement within the combined uncertainties, thus the equivalence of the measurements is demonstrated. [ABSTRACT FROM AUTHOR]

Conversion coefficients (CCs) are an essential vehicle in radiation protection for the determination of the dose (rate) of a given radiation field. According to the current draft of the revision of international standard ISO 4037, an X-ray field is a reference field if the CCs of the field match the tabulated ISO values within 2%. Deviations of the high-voltage (HV) tube-potential from its nominal value influence the resulting spectra and change the corresponding CCs. This work investigates the maximum allowable deviation of the HV from its nominal value such that the requirements of ISO 4037 remain fulfilled. This is achieved using both synthetic spectra created by a software simulation program and spectra measured at one of the X-ray facilities of the Physikalisch-Technische Bundesanstalt. The results are summarised in form of a new proposal for upper limit values which are suggested to be used in the next version of ISO 4037. [ABSTRACT FROM AUTHOR]

An intercomparison of eye lens dosemeters has been conducted in terms of the quantity Hp(3). For the first time, besides photon radiation also beta radiation qualities were included. Three dosemeter types designed for the quantity Hp(3) and ten for Hp(0.07) took part in the intercomparison. As shown in a previous intercomparison for photon radiation only, the dosemeters designed for Hp(0.07) and calibrated in terms of Hp(3) performed well in photon radiation fields. But for beta radiation, it turned out that Hp(0.07) dosemeters over-responded up to a factor of 5 000 (with respect to the true Hp(3) dose) in the medium beta energy range (85Kr with a beta endpoint energy of 0.69 MeV), while some Hp(3) dosemeters performed quite well. For medium (57 keV) and high (662 keV) energy photon radiation, all dosemeter types showed response values well within the trumpet curve according to the current draft of ISO 14146. [ABSTRACT FROM AUTHOR]

Conversion coefficients are a substantial vehicle in practical radiation protection to determine the dose (rate) of a given radiation field. According to ICRU report 57, their values shall be obtained by means of spectrometry. This is, however, a time-consuming complicated procedure that cannot be performed by all dosimetry laboratories. Therefore, it is desired to find acceptable alternative methods to replace spectrometry. One possibility is to set up the X-ray facility in accordance with international standard ISO 4037-1:1997 and use the tabulated values from that standard. However, this needs to be considered during the construction phase of the X-ray facility. In this work, the combined usage of half-value layer measurements and the effective energy (both with respect to air kerma) to determine the conversion coefficients is investigated and compared with the values obtained by spectrometry. The investigations utilise all combinations of the H-, W-, N- and L-series, reference distances of 1 and 2.5 m and aluminium and copper as attenuation materials. We find that for most of the radiation qualities, the investigated method results in conversion coefficients that show an unacceptable deviation from the conventionally true values. However, the values of conversion coefficients of selected N- and L-qualities could be reproduced with high accuracy (within ±1 %). [ABSTRACT FROM AUTHOR]

In the past, the operational quantity Hp(3) was defined for calibration purposes in a slab phantom. Recently, an additional phantom in the form of a cylinder has been suggested for eye lens dosimetry, as a cylinder much better approximates the shape of a human head. Therefore, this work investigates which of the two phantoms, slab or cylinder, is more suitable for calibrations and type tests of eye dosemeters. For that purpose, a typical Hp(3) eye dosemeter was irradiated on a slab, a cylinder and on a human-like Alderson phantom. It turned out that the response on the three phantoms is nearly equal for angles of radiation incidence up to 45° and deviates only at larger angles of incidence. Thus, calibrations (usually performed at 0° radiation incidence) are practically equivalent on both the slab and the cylinder phantoms. However, type tests (up to 75° or even 90° radiation incidence) should be carried out on a cylinder phantom, as also for large angles of incidence the response on the cylinder and the Alderson phantoms is rather similar, whereas the response on the slab significantly deviates from the one on the Alderson phantom. [ABSTRACT FROM AUTHOR]