Search

The deprived electrochemical kinetics of the oxygen evolution reaction (OER) catalyst is the prime bottleneck and remains the major obstacle in the water electrolysis processes. Herein, a facile hydrothermal technique was implemented to form a freestanding polyhedron-like Co3O4 on the microporous architecture of Ni foam, its reaction kinetics enhanced through sulfide counterpart transformation in the presence of Na2S, and their catalytic OER performances comparatively investigated in 1 M KOH medium. The formed Co3S4 catalyst shows outstanding catalytic OER activity at a current density of 100 mA cm−2 by achieving a relatively low overpotential of 292 mV compared to the pure Co3O4 catalyst and the commercial IrO2 catalyst. This enhancement results from the improved active centers and conductivity, which boost the intrinsic reaction kinetics. Further, the optimized Co3S4 catalyst exhibits admirable prolonged durability up to 72 h at varied current rates with insignificant selectivity decay. The energy dispersive X-ray spectroscopy (EDX) and Raman spectra measured after the prolonged OER stability test reveal a partial transformation of the active catalyst into an oxyhydroxide phase (i.e., CoOOH@Co3S4), which acts as an active catalyst phase during the electrolysis process.

Developing effective and long-lasting electrocatalysts for oxygen evolution reaction (OER) is critical for increasing sustainable hydrogen production. This paper describes the production and characterization of CoFeP nanoparticles (CFP NPs) as high-performance electrocatalysts for OER. The CFP NPs were produced using a simple hydrothermal technique followed by phosphorization, yielding an amorphous/crystalline composite structure with improved electrochemical characteristics. Our results reveal that CFP NPs have a surprisingly low overpotential of 284 mV at a current density of 100 mA cm−2, greatly exceeding the precursor CoFe oxide/hydroxide (CFO NPs) and the commercial RuO2 catalyst. Furthermore, CFP NPs demonstrate exceptional stability, retaining a constant performance after 70 h of continuous operation. Post-OER characterization analysis revealed transformations in the catalyst, including the formation of cobalt–iron oxides/oxyhydroxides. Despite these changes, CFP NPs showed superior long-term stability compared to native metal oxides/oxyhydroxides, likely due to enhanced surface roughness and increased active sites. This study proposes a viable strategy for designing low-cost, non-precious metal-based OER catalysts, which will help advance sustainable energy technology.

Water electrolysis is a highly efficient route to produce ideally clean H2 fuel with excellent energy conversion efficiency and high gravimetric energy density, without producing carbon traces, unlike steam methane reforming, and it resolves the issues of environmental contamination via replacing the conventional fossil fuel. Particular importance lies in the advancement of highly effective non-precious catalysts for the oxygen evolution reaction (OER). The electrocatalytic activity of an active catalyst mainly depends on the material conductivity, accessible catalytically active sites, and intrinsic OER reaction kinetics, which can be tuned via introducing N heteroatoms in the catalyst structure. Herein, the efficacious nitrogenation of CuS was accomplished, synthesized using a hydrothermal procedure, and characterized for its electrocatalytic activity towards OER. The nitrogen-doped CuO@CuS (N,CuO@CuS) electrocatalyst exhibited superior OER activity compared to pristine CuS (268 and 602 mV), achieving a low overpotential of 240 and 392 mV at a current density of 10 and 100 mA/cm2, respectively, ascribed to the favorable electronic structural modification triggered by nitrogen incorporation. The N,CuO@CuS also exhibits excellent endurance under varied current rates and a static potential response over 25 h with stability measured at 10 and 100 mA/cm2.

Double perovskites are known for their special structures which can be utilized as catalyst electrode materials for electrochemical water splitting to generate carbon-neutral hydrogen energy. In this work, we prepared lanthanide series metal-doped double perovskites at the M site such as M2NiMnO6 (where M = Eu, Gd, Tb) using the solid-state reaction method, and they were investigated for an oxygen evolution reaction (OER) study in an alkaline medium. It is revealed that the catalyst with a configuration of Tb2NiMnO6 has outstanding OER properties such as a low overpotential of 288 mV to achieve a current density of 10 mAcm−2, a lower Tafel slope of 38.76 mVdec−1, and a long cycling stability over 100 h of continuous operation. A-site doping causes an alteration in the oxidation or valence states of the NiMn cations, their porosity, and the oxygen vacancies. This is evidenced in terms of the Mn4+/Mn3+ ratio modifying electronic properties and the surface which facilitates the OER properties of the catalyst. This is discussed using electrochemical impedance spectroscopy (EIS) and electrochemical surface area (ECSA) of the catalysts. The proposed work is promising for the synthesis and utilization of future catalyst electrodes for high-performance electrochemical water splitting.

Layered double hydroxides (LDHs) have gained vast importance as an electrocatalyst for water electrolysis to produce carbon-neutral and clean hydrogen energy. In this work, we demonstrated the fabrication of nano-flake-like NiMn LDH thin film electrodes onto porous membrane-like Ni-foam by using a simple and cost-effective electrodeposition method for oxygen evolution reaction (OER). Various Ni1-xMnx LDH (where x = 0.15, 0.25, 0.35, 0.50 and 0.75) thin film electrodes are utilized to achieve the optimal catalyst for an efficient and sustainable OER process. The various composition-dependent surface morphologies and porous-membrane-like structure provided the high electrochemical surface area along with abundant active sites facilitating the OER. The optimized catalyst referred to as Ni0.65Mn0.35 showed excellent OER properties with an ultralow overpotential of 253 mV at a current density of 50 mAcm−2, which outperforms other state-of-the art catalysts reported in the literature. The relatively low Tafel slope of 130 mV dec−1 indicates faster and more favorable reaction kinetics for OER. Moreover, Ni0.65Mn0.35 exhibits excellent durability over continuous operation of 20 h, indicating the great sustainability of the catalyst in an alkaline medium. This study provides knowledge for the fabrication and optimization of the OER catalyst electrode for water electrolysis.

A metal–organic framework (MOF) is a highly porous material with abundant redox capacitive sites for intercalation/de-intercalation of charges and, hence, is considered promising for electrode materials in supercapacitors. In addition, dopants can introduce defects and alter the electronic structure of the MOF, which can affect its surface reactivity and electrochemical properties. Herein, we report a copper-doped iron-based MOF (Cu@Fe-MOF/NF) thin film obtained via a simple drop-cast route on a 3D-nickel foam (NF) substrate for the supercapacitor application. The as-deposited Cu@Fe-MOF/NF electrodes exhibit a unique micro-sized bipyramidal structure composited with nanoparticles, revealing a high specific capacitance of 420.54 F g−1 at 3 A g−1 which is twice compared to the nano-cuboidal Fe-MOF/NF (210 F g−1). Furthermore, the asymmetric solid-state (ASSSC) supercapacitor device, derived from the assembly of Cu@Fe-MOF/NFǁrGO/NF electrodes, demonstrates superior performance in terms of energy density (44.20 Wh.kg−1) and electrochemical charge–discharge cycling durability with 88% capacitance retention after 5000 cycles. This work, thus, demonstrates a high potentiality of the Cu@Fe-MOF/NF film electrodes in electrochemical energy-storing devices.

Utilizing zeolitic imidazolate frameworks (ZIFs) poses a significant challenge that demands a facile synthesis method to produce uniform and nanometer-scale materials with high surface areas while achieving high yields. Herein, we demonstrate a facile and cost-effective strategy to systematically produce ZIF8 nanocrystals. Typically, ZIF8 nanocrystal synthesis involves a wet chemical route. As the reaction time decreased (150, 120, and 90 min), the size of the ZIF8 crystals decreased with uniform morphology, and productivity reached as high as 89%. The composition of the product was confirmed through XRD, FE-SEM, TEM, EDS, and Raman spectroscopy. The ZIF8 synthesized with different reaction time was finally employed for catalyzing the electrochemical hydrogen evaluation reaction (HER). The optimized ZIF8-3 obtained at 90 min of reaction time exhibited a superior catalytic action on the HER in alkaline medium, along with a remarkably long-term stability for 24 h compared with the other ZIF8 nanocrystals obtained at different reaction times. Specifically, the optimized ZIF8-3 sample revealed an HER overpotential of 172 mV and a Tafel slope of 104.15 mV·dec−1. This finding, thus, demonstrates ZIF8 as a promising electrocatalyst for the production of high-value-added green and sustainable hydrogen energy.

We have developed chelator-free copper-64-incorporated iron oxide (IO) nanoparticle (NPs) which have both magnetic and radioactive properties being applied to positron emission tomography (PET)-magnetic resonance imaging (MRI). We have found that the IO nanoparticles composed of radioactive isotope 64Cu may act as a contrast agent being a diagnostic tool for PET as well as a good T2 MRI nanoprobe due to their good r2/r1 ratio. Furthermore, we demonstrate that the 64Cu incorporation at the core of core-shell-structured IO NPs exhibits a good in vivo stability, giving us an insightful strategy for the design of a contrast agent for the PET-MRI system.

Developing efficient electrocatalysts for urea oxidation reaction (UOR) can be a promising alternative strategy to substitute the sluggish oxygen evolution reaction (OER), thereby producing hydrogen at a lower cell-voltage. Herein, we synthesized a binder-free thin film of ultrathin sheets of bimetallic Cu-Fe-based metal–organic frameworks (Cu/Fe-MOFs) on a nickel foam via a drop-casting route. In addition to the scalable route, the drop-casted film-electrode demonstrates the lower UOR potentials of 1.59, 1.58, 1.54, 1.51, 1.43 and 1.37 V vs. RHE to achieve the current densities of 2500, 2000, 1000, 500, 100 and 10 mA cm−2, respectively. These UOR potentials are relatively lower than that acquired by the pristine Fe-MOF-based film-electrode synthesized via a similar route. For example, at 1.59 V vs. RHE, the Cu/Fe-MOF electrode exhibits a remarkably ultra-high anodic current density of 2500 mA cm−2, while the pristine Fe-MOF electrode exhibits only 949.10 mA cm−2. It is worth noting that the Cu/Fe-MOF electrode at this potential exhibits an OER current density of only 725 mA cm−2, which is far inconsequential as compared to the UOR current densities, implying the profound impact of the bimetallic cores of the MOFs on catalyzing UOR. In addition, the Cu/Fe-MOF electrode also exhibits a long-term electrochemical robustness during UOR.

Ammonium toxicity is a significant source of pollution from industrial civilization that is disrupting the balance of natural systems, adversely affecting soil and water quality, and causing several environmental problems that affect aquatic and human life, including the strong promotion of eutrophication and increased dissolved oxygen consumption. Thus, a cheap catalyst is required for power generation and detoxification. Herein, compost soil is employed as a novel electrocatalyst for ammonium degradation and high-power generation. Moreover, its effect on catalytic activity and material performances is systematically optimized and compared by treating it with various reducing agents, including potassium ferricyanide, ferrocyanide, and manganese dioxide. Ammonium fuel was supplied to the compost soil ammonium fuel cell (CS-AFC) at concentrations of 0.1, 0.2, and 0.3 g/mL. The overall results show that ferricyanide affords a maximum power density of 1785.20 mW/m2 at 0.2 g/mL fuel concentration. This study focuses on high-power generation for CS-AFC. CS-AFCs are sustainable for many hours without any catalyst deactivation; however, they need to be refueled at regular intervals (every 12 h). Moreover, CS-AFCs afford the best performance when ferricyanide is used as the electron acceptor at the cathode. This study proposes a cheap electrocatalyst and possible solutions to the more serious energy generation problems. This study will help in recycling ammonium-rich wastewaters as free fuel for running CS-AFC devices to yield high-power generation with reducing agents for ammonium fuel cell power applications.

A very simple, as well as sensitive and selective, sensing protocol was developed on a pre-anodized graphite pencil electrode surface coated using poly(thionine) (APGE/PTH). The poly(thionine) coated graphite pencil was then used for simultaneous sensing of 3-nitrophenol (3-NP) and 4-nitrophenol (4-NP). The poly(thionine) coated electrode exhibited an enhanced electrocatalytic property towards nitrophenol (3-NP and 4-NP) reduction. Redox peak potential and current of both nitrophenols were found well resolved and their simultaneous analysis was studied. Under optimized experimental conditions, APGE/PTH showed a long linear concentration range from 20 to 230 nM and 15 nM to 280 nM with a calculated limit of detection (LOD) of 4.5 and 4 nM and a sensitivity of 22.45 µA/nM and 27.12 µA/nM for 3-NP and 4-NP, respectively. Real sample analysis using the prepared sensor was tested with different environmental water samples and the sensors exhibited excellent recovery results in the range from 98.16 to 103.43%. Finally, the sensor exposed an promising selectivity, stability, and reproducibility towards sensing of 3-NP and 4-NP.

This work reports the fabrication of vanadium sulfide (VS2) microflower via one-step solvo-/hydro-thermal process. The impact of ethylene glycol on the VS2 morphology and crystal structure as well as the ensuing influences on electrocatalytic hydrogen evolution reaction (HER) and supercapacitor performance are explored and compared with those of the VS2 obtained from the standard pure-aqueous and pure-ethylene glycol solvents. The optimized VS2 obtained from the ethylene glycol and water mixed solvents exhibits a highly ordered unique assembly of petals resulting a highly open microflower structure. The electrode based on the optimized VS2 and exhibits a promising HER electrocatalysis in 0.5 M H2SO4 and 1 M KOH electrolytes, attaining a low overpotential of 161 and 197 mV, respectively, at 10 mA.cm−2 with a small Tafel slope 83 and 139 mVdec−1. In addition, the optimized VS2 based electrode exhibits an excellent electrochemical durability over 13 h. Furthermore, the superior VS2 electrode based symmetric supercapacitor delivers a specific capacitance of 139 Fg−1 at a discharging current density of 0.7 Ag−1 and exhibits an enhanced energy density of 15.63 Whkg−1 at a power density 0.304 kWkg−1. Notably, the device exhibits the capacity retention of 86.8% after 7000 charge/discharge cycles, demonstrating a high stability of the VS2 electrode.

The dataset presented here is related to the research article entitled “Highly Efficient Electro-optically Tunable Smart-supercapacitors Using an Oxygen-excess Nanograin Tungsten Oxide Thin Film” (Akbar et al., 2017) [9] where we have presented a nanograin WO3 film as a bifunctional electrode for smart supercapacitor devices. In this article we provide additional information concerning nanograin tungsten oxide thin films such as atomic force microscopy, Raman spectroscopy, and X-ray diffraction spectroscopy. Moreover, their electrochemical properties such as cyclic voltammetry, electrochemical supercapacitor properties, and electrochromic properties including coloration efficiency, optical modulation and electrochemical impedance spectroscopy are presented.

With the motivation of materializing a high-performance electrode material for the high-energy supercapacitor, ultrathin mesoporous graphitic‑carbon was synthesized from biomass green-tea wastes via the KOH activation process combined with either of the water or the hydrochloric acid treatment. The water-treated graphitic‑carbon showed an interconnected ultrathin-nanoflake structure with a high porosity, while the hydrochloric acid-treated graphitic carbon exhibited an aggregated structure of irregular nanoparticles. The supercapacitor with an electrode of water-treated graphitic‑carbon nanoflakes displayed an enhanced specific capacitance of 162 F/g at 0.5 A/g. Furthermore, the device revealed an excellent cycle stability after multiple cyclic charge-discharge operations (i.e., 121% cyclic capacitance retention over 5000 cycles). These may open up a new avenue toward the recycling of biomass carbonaceous resources (e.g., green tea wastes) for inexpensive high-performance electrochemical energy-storage devices such as high-energy supercapacitors. Keywords: Biomass resource, Green tea waste, Graphitic carbon, Nanoflakes, Electrode, Supercapacitor

Bismuth doped ZnO (ZnBi0.03O0.97) thin films are grown using pulsed laser deposition. The existence of positively charged Bi, absence of metallic zinc and the Zn-O bond formation in Bi doped ZnO are confirmed using X-ray Photoelectron Spectroscopy (XPS). Temperature dependent resistivity and UV-visible absorption spectra show lowest resistivity with 8.44 × 10-4 Ω cm at 300 K and average transmittance of 93 % in the visible region respectively. The robust ferromagnetic signature is observed at 350 K (7.156 × 10-4 emu/g). This study suggests that Bi doped ZnO films should be a potential candidate for spin based optoelectronic applications.

The nanocomposites of activated-carbon-decorated silicon nanocrystals (ACAC) were synchronously derived in a single step from biomass rice husks, through the simple route of the calcination method together with the magnesiothermic reduction process. The final product, ACAC, exhibited an aggregated structure of activated-carbon-encapsulated nanocrystalline silicon spheres, and reveals a high specific surface area (498.5 m2/g). Owing to the mutualization of advantages from both silicon nanocrystals (i.e., low discharge potential and high specific capacity) and activated carbon (i.e., high porosity and good electrical conductivity), the ACAC nanocomposites are able to play a substantial role as an anodic source material for the lithium-ion battery (LIB). Namely, a high coulombic efficiency (97.5%), a high discharge capacity (716 mAh/g), and a high reversible specific capacity (429 mAh/g after 100 cycles) were accomplished when using ACAC as an LIB anode. The results advocate that the simultaneous synthesis of biomass-derived ACAC is beneficial for green energy-storage device applications.

A transparent polymer-based resistive switching device containing In2O3 nanocrystals (NCs) is fabricated, and its nonvolatile memory characteristics are evaluated. Very clear reversible counter-clockwise bipolar-type resistive switching phenomena are observed. Stable retention is demonstrated. An Analysis of the temperature dependence of the bistable resistance states reveals additional features, not reported in previous studies, that the observed resistance switching is due to oxygen ions drift-induced redox reactions at the polymer/In2O3 NCs interface. The RESET and SET switching times (τRESET and τSET), which are defined as pulse widths extrapolated by the steepest slopes in the transition region, are τRESET ∼ 550 nsec and τSET ∼ 900 nsec. The authors propose that microscopic potential modification occurring near the polymer/In2O3 NCs boundaries plays a key role in determining resistive switching properties.

The hydrogen evolution reaction (HER) represents the key step in sustainable energy development. This study presents a novel approach to the HER through value-added formate synthesis utilizing methanol electrolysis in both fresh and seawater environments. This approach leverages electronically modulated nickel nodes of a metal--organic framework (e-Ni MOF) via zinc doping, demonstrating significant enhancement in catalytic performance and energy efficiency owing to the synergistic effects of zinc and nickel, thereby facilitating electron transfer and thus lowering the energy barrier for high-valent Ni-active catalytic phase formation. Specifically, the e-Ni MOF anode-based electrolyzer using a 1.0 M methanol solution in an industrially relevant 30 wt% KOH-seawater electrolyte demonstrated a remarkably lower cell voltage of 1.10 V at 10 mA cm-2. Additionally, it achieved an 11.5-fold higher hydrogen evolution rate by replacing the oxygen evolution reaction (OER) with the methanol oxidation reaction (MeOR). At an industrially relevant current density of 250 mA cm-2, the electrolyzer could lead to an energy saving of 640 W h of electricity compared to a conventional OER system. Moreover, the e-Ni MOF facilitated hydrogen evolution at the cathode and produced formate as a value-added chemical from the MeOR at the anodic side. This dual-benefit approach underscores the potential of e-modulated Ni MOFs in transforming hydrogen evolution processes, offering a sustainable and energy-efficient pathway for hydrogen production from seawater and supporting the goal of carbon-neutral energy solutions. [ABSTRACT FROM AUTHOR]

Extensive efforts are being dedicated to developing high-performance electrocatalysts for water splitting to achieve efficient and stable hydrogen production, especially under high current densities. In this study, we synthesised a CoMo microcolumn arrays (MCA)/Fe-nanowires (NWs)/nickel foam (NF) catalyst through a simple yet effective combination of hydrothermal and solution-based methods. This catalyst exhibits remarkable performance during the oxygen evolution reaction (OER), achieving a low overpotential of 425 mV at a current density of 2000 mA cm-2 and maintaining stability for 200 h at a current density of 1000 mA cm-2 in 1 M KOH. In natural alkaline seawater, the catalyst demonstrates an overpotential of 464 mV at a current density of 1000 mA cm-2, with stability extending to 250 h at a current density of 500 mA cm-2. These overpotentials are lower than that required for hypochlorite production (>490 mV). Furthermore, during alkaline full seawater splitting, the synthesised catalyst delivers a cell voltage of 1.861 V at a current density of 1000 mA cm-2, sustaining stability for 100 h at a current density of 500 mA cm-2. The heterointerfaces in the CoMo-MCA/Fe-NWs/NF structure optimise the electronic configuration, enhancing OER activity. The MCA structure and Fe2O3 NWs increase the electrochemically active surface area, providing numerous active sites and ensuring long-term durability under harsh conditions. This study suggests a promising approach for industrial-scale seawater electrolysis by engineering effective heterostructures and interfacial active sites. [ABSTRACT FROM AUTHOR]