Search

Using field-effect transistors (FETs) to explore atomically thin magnetic semiconductors with transport measurements is difficult, because the very narrow bands of most 2D magnetic semiconductors cause carrier localization, preventing transistor operation. Here, we show that exfoliated layers of CrPS$_4$ -- a 2D layered antiferromagnetic semiconductor whose bandwidth approaches 1 eV -- allow the realization of FETs that operate properly down to cryogenic temperature. Using these devices, we perform conductance measurements as a function of temperature and magnetic field, to determine the full magnetic phase diagram, which includes a spin-flop and a spin-flip phase. We find that the magnetoconductance depends strongly on gate voltage, reaching values as high as 5000 % near the threshold for electron conduction. The gate voltage also allows the magnetic states to be tuned, despite the relatively large thickness of the CrPS$_4$ multilayers employed in our study. Our results show the need to employ 2D magnetic semiconductors with sufficiently large bandwidth to realize properly functioning transistors, and identify a candidate material to realize a fully gate-tunable half-metallic conductor., Accepted for publication in Advanced Materials

Ionic gating is a powerful technique to realize field-effect transistors (FETs) enabling experiments not possible otherwise. So far, ionic gating has relied on the use of top-electrolyte gates, which pose experimental constraints and make device fabrication complex. Promising results obtained recently in FETs based on solid-state electrolytes remain plagued by spurious phenomena of unknown origin, preventing proper transistor operation, and causing limited control and reproducibility. Here we explore a class of solid-state electrolytes for gating (Lithium-ion conducting glass-ceramics, LICGCs), identify the processes responsible for the spurious phenomena and irreproducible behavior,and demonstrate properly functioning transistors exhibiting high density ambipolar operation with gate capacitance of ~20-50 $\mu$F/cm$^2$ (depending on the polarity of the accumulated charges). Using two-dimensional semiconducting transition-metal dichalcogenides we demonstrate the ability to implement ionic-gate spectroscopy to determine the semiconducting bandgap, and to accumulate electron densities above 10$^{14}$ cm$^{-2}$, resulting in gate-induced superconductivity in MoS$_2$ multilayers. As LICGCs are implemented in a back-gate configuration, they leave the surface of the material exposed, enabling the use of surface-sensitive techniques (such as scanning tunneling microscopy and photoemission spectroscopy) impossible so far in ionic-liquid gated devices. They also allow double ionic gated devices providing independent control of charge density and electric field.

We report experimental investigations of transport through bilayer graphene (BLG)/chromium trihalide (CrX

We investigate electronic transport through exfoliated multilayers of CrSBr, a 2D semiconductor that is attracting attention because of its magnetic properties. We find an extremely pronounced anisotropy that manifests itself in qualitative and quantitative differences of all quantities measured along the in-plane \textit{a} and \textit{b} crystallographic directions. In particular, we observe a qualitatively different dependence of the conductivities $\sigma_a$ and $\sigma_b$ on temperature and gate voltage, accompanied by orders of magnitude differences in their values ($\sigma_b$/$\sigma_a \approx 3\cdot10^2-10^5$ at low temperature and large negative gate voltage). We also find a different behavior of the longitudinal magnetoresistance in the two directions, and the complete absence of the Hall effect in transverse resistance measurements. These observations appear not to be compatible with a description in terms of conventional band transport of a 2D doped semiconductor. The observed phenomenology -- together with unambiguous signatures of a 1D van Hove singularity that we detect in energy resolved photocurrent measurements -- indicate that electronic transport through CrSBr multilayers is better interpreted by considering the system as formed by weakly and incoherently coupled 1D wires, than by conventional 2D band transport. We conclude that CrSBr is the first 2D semiconductor to show distinctly quasi 1D electronic transport properties., Comment: Accepted for publication in Advanced Materials

We report experimental investigations of transport through bilayer graphene (BLG)/chromium trihalide (CrX$_3$; X=Cl, Br, I) van der Waals interfaces. In all cases, a large charge transfer from BLG to CrX$_3$ takes place (reaching densities in excess of $10^{13}$ cm$^{-2}$), and generates an electric field perpendicular to the interface that opens a band gap in BLG. We determine the gap from the activation energy of the conductivity and find excellent agreement with the latest theory accounting for the contribution of the $\sigma$ bands to the BLG dielectric susceptibility. We further show that for BLG/CrCl$_3$ and BLG/CrBr$_3$ the band gap can be extracted from the gate voltage dependence of the low-temperature conductivity, and use this finding to refine the gap dependence on the magnetic field. Our results allow a quantitative comparison of the electronic properties of BLG with theoretical predictions and indicate that electrons occupying the CrX$_3$ conduction band are correlated.

Perpendicular electric fields can tune the electronic band structure of atomically thin semiconductors. In bilayer graphene, which is an intrinsic zero-gap semiconductor, a perpendicular electric field opens a finite bandgap. So far, however, the same principle could not be applied to control the properties of a broader class of 2D materials because the required electric fields are beyond reach in current devices. To overcome this limitation, we design double ionic gated transistors that enable the application of large electric fields of up to 3 V nm

The assembly of suitably designed van der Waals (vdW) heterostructures represents a new approach to produce artificial systems with engineered electronic properties. Here, we apply this strategy to realize synthetic semimetals based on vdW interfaces formed by two different semiconductors. Guided by existing ab-initio calculations, we select WSe$_2$ and SnSe$_2$ mono and multilayers to assemble vdW interfaces, and demonstrate the occurrence of semimetallicity by means of different transport experiments. Semimetallicity manifests itself in a finite minimum conductance upon sweeping the gate over a large range in ionic liquid gated devices, which also offer spectroscopic capabilities enabling the quantitative determination of the band overlap. The semimetallic state is additionally revealed in Hall effect measurements by the coexistence of electrons and holes, observed by either looking at the evolution of the Hall slope with sweeping the gate voltage or with lowering temperature. Finally, semimetallicity results in the low-temperature metallic conductivity of interfaces of two materials that are themselves insulating. These results demonstrate the possibility to implement a state of matter that had not yet been realized in vdW interfaces, and represent a first step towards using these interfaces to engineer topological or excitonic insulating states.

Recent experiments on van der Waals antiferromagnets have shown that measuring the temperature (T) and magnetic field (H) dependence of the conductance allows their magnetic phase diagram to be mapped. Similarly, experiments on ferromagnetic CrBr3 barriers enabled the Curie temperature to be determined at H = 0, but a precise interpretation of the magnetoconductance data at H ≠ 0 is conceptually more complex, because at finite H there is no well-defined phase boundary. Here we perform systematic transport measurements on CrBr3 barriers and show that the tunneling magnetoconductance depends on H and T exclusively through the magnetization M(H, T) over the entire temperature range investigated. The phenomenon is reproduced by the spin-dependent Fowler–Nordheim model for tunneling, and is a direct manifestation of the spin splitting of the CrBr3 conduction band. Our analysis unveils a new approach to probe quantitatively different properties of atomically thin ferromagnetic insulators related to their magnetization by performing simple conductance measurements., Many standard techniques for investigating magnetic properties in the bulk are ill suited to atomically thin van der Waals materials. Here, Wang et al take a prototypical van der Waals ferromagnet, Chromium Bromide, and show how tunneling conductance can elucidate the material magnetic properties.

The field of two-dimensional materials has been developing at an impressive pace, with atomically thin crystals of an increasing number of different compounds that have become available, together with techniques enabling their assembly into functional heterostructures. The strategy to detect these atomically thin crystals has however remained unchanged since the discovery of graphene. Such an absence of evolution is starting to pose problems because for many of the 2D materials of current interest the optical contrast provided by the commonly used detection procedure is insufficient to identify the presence of individual monolayers or to determine unambiguously the thickness of atomically thin multilayers. Here we explore an alternative detection strategy, in which the enhancement of optical contrast originates from the use of optically inhomogeneous substrates, leading to diffusively reflected light. Owing to its peculiar polarization properties and to its angular distribution, diffusively reflected light allows a strong contrast enhancement to be achieved through the implementation of suitable illumination-detection schemes. We validate this conclusion by carrying out a detailed quantitative analysis of optical contrast, which fully reproduces our experimental observations on over 60 WSe$_2$ mono-, bi-, and trilayers. We further validate the proposed strategy by extending our analysis to atomically thin phosphorene, InSe, and graphene crystals. Our conclusion is that the use of diffusively reflected light to detect and identify atomically thin layers is an interesting alternative to the common detection scheme based on Fabry-Perot interference, because it enables atomically thin layers to be detected on substrates others than the commonly used Si/SiO$_2$, and it may offer higher sensitivity depending on the specific 2D material considered.

Reliable and precise measurements of the relative energy of band edges in semiconductors are needed to determine band gaps and band offsets, as well as to establish the band diagram of devices and heterostructures. These measurements are particularly important in the field of two-dimensional materials, in which many new semiconducting systems are becoming available through exfoliation of bulk crystals. For two-dimensional semiconductors, however, commonly employed techniques suffer from difficulties rooted either in the physics of these systems, or of technical nature. The very large exciton binding energy, for instance, prevents the band gap to be determined from a simple spectral analysis of photoluminescence, and the limited lateral size of atomically thin crystals makes the use of conventional scanning tunneling spectroscopy cumbersome. Ionic gate spectroscopy is a newly developed technique that exploits ionic gate field-effect transistors to determine quantitatively the relative alignment of band edges of two-dimensional semiconductors in a straightforward way, directly from transport measurements (i.e., from the transistor electrical characteristics). The technique relies on the extremely large geometrical capacitance of ionic gated devices that -- under suitable conditions -- enables a change in gate voltage to be directly related to a shift in chemical potential. Here we present an overview of ionic gate spectroscopy, and illustrate its relevance with applications to different two-dimensional semiconducting transition metal dichalcogenides and van der Waals heterostructures.

Van der Waals (vdW) materials offer new ways to assemble artificial electronic media with properties controlled at the design stage, by combining atomically defined layers into interfaces and heterostructures. Their potential for optoelectronics stems from the possibility to tailor the spectral response over a broad range by exploiting interlayer transitions between different compounds with an appropriate band-edge alignment. For the interlayer transitions to be radiative, however, a serious challenge comes from details of the materials --such as lattice mismatch or even a small misalignment of the constituent layers-- that can drastically suppress the electron-photon coupling. The problem was evidenced in recent studies of heterostructures of monolayer transition metal dichalcogenides, whose band edges are located at the K-point of reciprocal space. Here we demonstrate experimentally that the solution to the interlayer coupling problem is to engineer type-II interfaces by assembling atomically thin crystals that have the bottom of the conduction band and the top of the valence band at the $\Gamma$-point, thus avoiding any momentum mismatch. We find that this type of vdW interfaces exhibits radiative optical transition irrespective of lattice constant, rotational/translational alignment of the two layers, or whether the constituent materials are direct or indirect gap semiconductors. The result, which is robust and of general validity, drastically broadens the scope of future optoelectronics device applications based on 2D materials.

Recent technical progress demonstrates the possibility of stacking together virtually any combination of atomically thin crystals of van der Waals bonded compounds to form new types of heterostructures and interfaces. As a result, there is the need to understand at a quantitative level how the interfacial properties are determined by the properties of the constituent 2D materials. We address this problem by studying the transport and optoelectronic response of two different interfaces based on transition-metal dichalcogenide monolayers, namely WSe2-MoSe2 and WSe2-MoS2. By exploiting the spectroscopic capabilities of ionic liquid gated transistors, we show how the conduction and valence bands of the individual monolayers determine the bands of the interface, and we establish quantitatively (directly from the measurements) the energetic alignment of the bands in the different materials as well as the magnitude of the interfacial band gap. Photoluminescence and photocurrent measurements allow us to conclude that the band gap of the WSe2-MoSe2 interface is direct in k space, whereas the gap of WSe2/MoS2 is indirect. For WSe2/MoSe2, we detect the light emitted from the decay of interlayer excitons and determine experimentally their binding energy using the values of the interfacial band gap extracted from transport measurements. The technique that we employed to reach this conclusion demonstrates a rather-general strategy for characterizing quantitatively the interfacial properties in terms of the properties of the constituent atomic layers. The results presented here further illustrate how van der Waals interfaces of two distinct 2D semiconducting materials are composite systems that truly behave as artificial semiconductors, the properties of which can be deterministically defined by the selection of the appropriate constituent semiconducting monolayers., Comment: Nano Letters 2018

Van der Waals (vdW) interfaces based on 2D materials are promising for optoelectronics, as interlayer transitions between different compounds allow tailoring of the spectral response over a broad range. However, issues such as lattice mismatch or a small misalignment of the constituent layers can drastically suppress electron-photon coupling for these interlayer transitions. Here, we engineered type-II interfaces by assembling atomically thin crystals that have the bottom of the conduction band and the top of the valence band at the Γ point, and thus avoid any momentum mismatch. We found that these van der Waals interfaces exhibit radiative optical transitions irrespective of the lattice constant, the rotational and/or translational alignment of the two layers or whether the constituent materials are direct or indirect gap semiconductors. Being robust and of general validity, our results broaden the scope of future optoelectronics device applications based on two-dimensional materials.

The recent discovery of ferromagnetism in 2D van der Waals (vdw) crystals has generated widespread interest, owing to their potential for fundamental and applied research. Advancing the understanding and applications of vdw magnets requires methods to quantitatively probe their magnetic properties on the nanoscale. Here, we report the study of atomically thin crystals of the vdw magnet CrI$_3$ down to individual monolayers using scanning single-spin magnetometry, and demonstrate quantitative, nanoscale imaging of magnetisation, localised defects and magnetic domains. We determine the magnetisation of CrI$_3$ monolayers to be $\approx16~\mu_B/$nm$^2$ and find comparable values in samples with odd numbers of layers, whereas the magnetisation vanishes when the number of layers is even. We also establish that this inscrutable even-odd effect is intimately connected to the material structure, and that structural modifications can induce switching between ferro- and anti-ferromagnetic interlayer ordering. Besides revealing new aspects of magnetism in atomically thin CrI$_3$ crystals, these results demonstrate the power of single-spin scanning magnetometry for the study of magnetism in 2D vdw magnets., Comment: Questions and comments are welcome. For further information and related job-openings, please visit www.quantum-sensing.ch

Many atomically thin exfoliated 2D materials degrade when exposed to ambient conditions. They can be protected and investigated by means of transport and optical measurements if they are encapsulated between chemically inert single layers in the controlled atmosphere of a glove box. Here, we demonstrate that the same encapsulation procedure is also compatible with scanning tunneling microscopy (STM) and spectroscopy (STS). To this end, we report a systematic STM/STS investigation of a model system consisting of an exfoliated 2H-NbSe2 crystal capped with a protective 2H-MoS2 monolayer. We observe different electronic coupling between MoS2 and NbSe2, from a strong coupling when their lattices are aligned within a few degrees to 2 essentially no coupling for 30{\deg} misaligned layers. We show that STM always probes intrinsic NbSe2 properties such as the superconducting gap and charge density wave at low temperature when setting the tunneling bias inside the MoS2 band gap, irrespective of the relative angle between the NbSe2 and MoS2 lattices. This study demonstrates that encapsulation is fully compatible with STM/STS investigations of 2D materials., Comment: 19 pages, 5 figures

Two-dimensional crystals of semi-metallic van der Waals materials hold much potential for the realization of novel phases, as exemplified by the recent discoveries of a polar metal in few-layer 1T'-WTe

We explore solid electrolytes for electrostatic gating using field-effect transistors (FETs) in which thin WSe$_2$ crystals are exfoliated and transferred onto a lithium-ion conducting glass ceramic substrate. For negative gate voltages ($V_G < 0$) the devices work equally well as ionic liquid gated FETs while offering specific advantages, whereas no transistor action is seen for $V_G>0$. For $V_G

We realize and investigate ionic liquid gated field-effect transistors (FETs) on large-area MoS2 monolayers grown by chemical vapor deposition (CVD). Under electron accumulation, the performance of these devices is comparable to that of FETs based on exfoliated flakes. FETs on CVD-grown material, however, exhibit clear ambipolar transport, which for MoS2 monolayers had not been reported previously. We exploit this property to estimate the bandgap {\Delta} of monolayer MoS2 directly from the device transfer curves and find {\Delta} $\approx$ 2.4-2.7 eV. In the ambipolar injection regime, we observe electroluminescence due to exciton recombination in MoS2, originating from the region close to the hole-injecting contact. Both the observed transport properties and the behavior of the electroluminescence can be consistently understood as due to the presence of defect states at an energy of 250-300 meV above the top of the valence band, acting as deep traps for holes. Our results are of technological relevance, as they show that devices with useful optoelectronic functionality can be realized on large-area MoS2 monolayers produced by controllable and scalable techniques.

Interfaces formed by two different organic semiconductors often exhibit a large conductivity, originating from transfer of charge between the constituent materials. The precise mechanisms driving charge transfer and determining its magnitude remain vastly unexplored, and are not understood microscopically. To start addressing this issue, we have performed a systematic study of highly reproducible single-crystal interfaces based on rubrene (tetraphenylnaphthacene) and Fx-TCNQ (fluorinated tetracyanoquinodimethane), a family of molecules whose electron affinity can be tuned by increasing the fluorine content. The combined analysis of transport and scanning Kelvin probe measurements reveals that the interfacial charge-carrier density, resistivity, and activation energy correlate with the electron affinity of Fx-TCNQ crystals, with a higher affinity resulting in larger charge transfer. Although the transport properties can be described consistently and quantitatively using a mobility-edge model, we find that a quantitative analysis of charge transfer in terms of single-particle band diagrams reveals a discrepancy ≈100 meV in the interfacial energy level alignment. We attribute the discrepancy to phenomena known to affect the energetics of organic semiconductors, which are neglected by a single-particle description—such as molecular relaxation and bandgap renormalization due to screening. The systematic behavior of the Fx-TCNQ/rubrene interfaces opens the possibility to investigate these phenomena experimentally, under controlled conditions.

It has been recently claimed that bulk crystals of transition metal dichalcogenide (TMD) ReS$_2$ are direct band gap semiconductors, which would make this material an ideal candidate, among all TMDs, for the realization of efficient opto-electronic devices. The situation is however unclear, because even more recently an indirect transition in the photoluminescence spectra of this material has been detected, whose energy is smaller than the supposed direct gap. To address this issue we exploit the properties of ionic liquid gated field-effect transistors (FETs) to investigate the gap structure of bulk ReS$_2$. Using these devices, whose high quality is demonstrated by a record high electron FET mobility of 1,100 cm$^2$/Vs at 4K, we can induce hole transport at the surface of the material and determine quantitatively the smallest band gap present in the material, irrespective of its direct or indirect nature. The value of the band gap is found to be 1.41 eV, smaller than the 1.5 eV direct optical transition but in good agreement with the energy of the indirect optical transition, providing an independent confirmation that bulk ReS$_2$ is an indirect band gap semiconductor. Nevertheless, contrary to the case of more commonly studied semiconducting TMDs (e.g., MoS$_2$, WS$_2$, etc.) in their bulk form, we also find that ReS$_2$ FETs fabricated on bulk crystals do exhibit electroluminescence when driven in the ambipolar injection regime, likely because the difference between the direct and indirect gap is only 100 meV. We conclude that ReS$_2$ does deserve more in-depth investigations in relation to possible opto-electronic applications., Comment: To appear in 2D Materials (19 pages, 4 Figures)

We realized ambipolar Field-Effect Transistors by coupling exfoliated thin flakes of tungsten disulphide (WS2) with an ionic liquid-dielectric. The devices show ideal electrical characteristics, including very steep sub-threshold slopes for both electrons and holes and extremely low OFF-state currents. Thanks to these ideal characteristics, we determine with high precision the size of the band-gap of WS2 directly from the gate-voltage dependence of the source-drain current. Our results demonstrate how a careful use of ionic liquid dielectrics offers a powerful strategy to study quantitatively the electronic properties of nano-scale materials., Comment: 21 pages, 5 figures

We realize and investigate ionic liquid gated field-effect transistors (FETs) on large-area MoS2 monolayers grown by chemical vapor deposition (CVD). Under electron accumulation, the performance of these devices is comparable to that of FETs based on exfoliated flakes. FETs on CVD-grown material, however, exhibit clear ambipolar transport, which for MoS2 monolayers had not been reported previously. We exploit this property to estimate the bandgap Δ of monolayer MoS2 directly from the device transfer curves and find Δ ≈ 2.4-2.7 eV. In the ambipolar injection regime, we observe electroluminescence due to exciton recombination in MoS2, originating from the region close to the hole-injecting contact. Both the observed transport properties and the behavior of the electroluminescence can be consistently understood as due to the presence of defect states at an energy of 250-300 meV above the top of the valence band, acting as deep traps for holes. Our results are of technological relevance, as they show that devices with useful optoelectronic functionality can be realized on large-area MoS2 monolayers produced by controllable and scalable techniques.

We study the evolution of the band-gap structure in few-layer MoTe$_2$ crystals, by means of low-temperature micro-reflectance (MR) and temperature-dependent photoluminescence (PL) measurements. The analysis of the measurements indicate that, in complete analogy with other semiconducting transition metal dichalchogenides (TMDs), the dominant PL emission peaks originate from direct transitions associated to recombination of excitons and trions. When we follow the evolution of the PL intensity as a function of layer thickness, however, we observe that MoTe$_2$ behaves differently from other semiconducting TMDs investigated earlier. Specifically, the exciton PL yield (integrated PL intensity) is identical for mono and bilayer and it starts decreasing for trilayers. A quantitative analysis of this behavior and of all our experimental observations is fully consistent with mono and bilayer MoTe$_2$ being direct band-gap semiconductors, with tetralayer MoTe$_2$ being an indirect gap semiconductor, and with trilayers having nearly identical direct and indirect gaps.This conclusion is different from the one reached for other recently investigated semiconducting transition metal dichalcogenides, for which only monolayers are found to be direct band-gap semiconductors, with thicker layers having indirect band gaps that are significantly smaller, by hundreds of meV, than the direct gap. We discuss the relevance of our findings for experiments of fundamental interest and possible future device applications., 20 pages, 4 Figures

We study the evolution of the band gap structure in few-layer MoTe2 crystals, by means of low-temperature microreflectance (MR) and temperature-dependent photoluminescence (PL) measurements. The analysis of the measurements indicate that in complete analogy with other semiconducting transition metal dichalchogenides (TMDs) the dominant PL emission peaks originate from direct transitions associated with recombination of excitons and trions. When we follow the evolution of the PL intensity as a function of layer thickness, however, we observe that MoTe2 behaves differently from other semiconducting TMDs investigated earlier. Specifically, the exciton PL yield (integrated PL intensity) is identical for mono and bilayer, decreases slightly for trilayer, and it is significantly lower in the tetralayer. The analysis of this behavior and of all our experimental observations is fully consistent with mono and bilayer MoTe2 being direct band gap semiconductors with tetralayer MoTe2 being an indirect gap semiconductor and with trilayers having nearly identical direct and indirect gaps. This conclusion is different from the one reached for other recently investigated semiconducting transition metal dichalcogenides for which monolayers are found to be direct band gap semiconductors, and thicker layers have indirect band gaps that are significantly smaller (by hundreds of meV) than the direct gap. We discuss the relevance of our findings for experiments of fundamental interest and possible future device applications.

Research on organic thin-film transistors tends to focus on improvements in device performance, but very little is understood about the ultimate limits of these devices, the microscopic physical mechanisms responsible for their limitations, and, more generally, the intrinsic transport properties of organic semiconductors. These topics are now being investigated through the study of transport in organic transistors realized using molecular single crystals of unprecedented chemical purity and structural quality. These studies are elucidating detailed microscopic aspects of the physics of organic semiconductors and corresponding devices and have also led to unforeseen high values for carrier mobility in these materials. Here, we discuss developments in this area and present a brief outlook on future goals that have now come into experimental reach., Comment: 18 pages, 4 Figures

Organic semiconductors based on small conjugated molecules generally behave as insulators when undoped, but the hetero-interfaces of two such materials can show electrical conductivity as large as in a metal. Although charge transfer is commonly invoked to explain the phenomenon, the details of the process and the nature of the interfacial charge carriers remain largely unexplored. Here we use Schottky-gated heterostructures to probe the conducting layer at the interface between rubrene and PDIF-CN2 single crystals. Gate-modulated conductivity measurements demonstrate that interfacial transport is due to electrons, whose mobility exhibits band-like behavior from room temperature to ~ 150 K, and remains as high as ~ 1 cm2V-1s-1 at 30 K for the best devices. The electron density decreases linearly with decreasing temperature, an observation that can be explained quantitatively based on the heterostructure band diagram. These results elucidate the electronic structure of rubrene-PDIF-CN2 interfaces and show the potential of Schottky-gated organic heterostructures for the investigation of transport in molecular semiconductors., Comment: 37 pages, 9 Figures (including supplementary information)

Semiconducting transition metal dichalcogenides (TMDs) have emerged as materials that can be used to realize two-dimensional (2D) crystals possessing rather unique transport and optical properties. Most research has so far focused on sulfur and selenium compounds, while tellurium-based materials attracted little attention so far. As a first step in the investigation of Te-based semiconducting TMDs in this context, we have studied MoTe$_2$ crystals with thicknesses above 4 nm, focusing on surface transport and a quantitative determination of the gap structure. Using ionic-liquid gated transistors, we show that ambipolar transport at the surface of the material is reproducibly achieved, with hole and electron mobility values between 10 and 30 cm$^2$/Vs at room temperature. The gap structure is determined through three different techniques: ionic-liquid gated transistors and scanning tunneling spectroscopy, that allow the measurement of the indirect gap ($E_{ind}$), and optical transmission spectroscopy on crystals of different thickness, that enables the determination of both the direct ($E_{dir}$) and the indirect gap. We find that at room temperature $E_{ind}$ = 0.88 eV and $E_{dir}$ = 1.02 eV. Our results suggest that thin MoTe$_2$ layers may exhibit a transition to a direct gap before mono-layer thickness. They should also drastically extend the range of direct gaps accessible in 2D semiconducting TMDs., 14 pages, 4 figures. To appear in 2D Materials

Monolayer jacutingaite (Pt$_2$HgSe$_3$) has been recently identified as a candidate quantum spin Hall system with a 0.5 eV band gap, but no transport measurements have been performed so far on this material, neither in monolayer nor in the bulk. By using a dedicated high-pressure technique, we grow crystals enabling the exfoliation of 50-100 nm thick layers and the realization of devices for controlled transport experiments. Magnetoresistance measurements indicate that jacutingaite is a semimetal, exhibiting Shubnikov-de Haas (SdH) resistance oscillations with a multi-frequency spectrum. We adapt the Lifshitz-Kosevich formula to analyze quantitatively the SdH resistance oscillations in the presence of multiple frequencies, and find that the experimental observations are overall reproduced well by band structure ab-initio calculations for bulk jacutingaite. Together with the relatively high electron mobility extracted from the experiments ($\approx 2000$ cm$^2$/Vs, comparable to what is observed in WTe$_2$ crystals of the same thickness), our results indicate that monolayer jacutingaite should provide an excellent platform to investigate transport in 2D quantum spin Hall systems., 11 pages, 4 figures + supplementary (3 pages, 2 figures)

We report the observation of an unexpected, long-range field-effect in WTe$_2$ devices, leading to large gate-induced changes of the transport properties of crystals much thicker than the electrostatic screening length. The phenomenon --which manifests itself very differently from the conventional field-effect-- originates from the non-local nature of transport in the devices that are thinner than the carrier mean free path, because of the dominant role of surface scattering. We reproduce theoretically the gate dependence of the measured classical and quantum magneto-transport in all detail, and show that the phenomenon is caused by the gate-tuning of the bulk carrier mobility by changing the scattering at the surface. Our results demonstrate the possibility to gate tune the electronic properties deep in the interior of conducting materials, avoiding limitations imposed by electrostatic screening., Comment: To appear in Physical Review Letters soon (Published online October 19th, 2016), 10 pages, 8 figures, including the Supplemental Material