Search

Crystal violet is a basic dye that is widely used by various industries, such as textiles and paints. These industries discharge their effluents, contaminated with crystal violet, into water streams, and these effluents have an adverse effect on aquatic organisms, the environment, and human health. Crystal violet is a basic dye that is widely used by various industries, such as textiles and paints. These industries discharge their effluents, contaminated with crystal violet, into water streams, and these effluents have an adverse effect on aquatic organisms, the environment, and human health. Hence, this paper is directed at studying the removal of crystal violet using environmentally friendly, cost-effective adsorbent materials such as raw fava bean (RFP-H3F), and chemically activated carbon (H3F) in comparison to commercial activated carbon (CAC).Various characterization techniques are applied, such as XRD, FT-IR,and SEM analyses. Then, the process of optimizing is shown through some preliminary experiments and a Response Surface Methodology (RSM) experiment to find the best conditions for removing crystal violet efficiently. Results revealed that the raw fava bean peels and the commercial activated carbon have the maximum removal efficiency of 95 %, and 83 % respectively, after 180 min of contact time. It is hypothesized that raw fava bean peels (RFP) and chemically activated carbon using phosphoric acid RFP-H3F will exhibit comparable efficiency in removing crystal violet when compared to commercial activated carbon (CAC). Various characterization techniques, including X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FT-IR),and scanning electron microscopy (SEM), are applied to analyze the properties of the adsorbent materials. Afterwards, the optimization process is displayed through some preliminary experiments followed by a Response Surface Methodology (RSM) experiment to obtain the optimum conditions, which achieve high crystal violet removal efficiency. The results demonstrate that both raw fava bean peels and commercial activated carbon exhibit significant removal efficiencies, with raw fava bean peels achieving a maximum removal efficiency of 95 % and commercial activated carbon achieving 83 %.

Corrosion poses a significant challenge in industrial sectors that handle metallic materials. The objective of this study was to evaluate the feasibility of employing a cost-effective, organic, and eco-friendly solution derived from discarded coffee grounds, known as coffee waste extract (CE), to mitigate the corrosion rate of carbon steel in an acidic environment comprising 0.5 M hydrochloric acid (HCL) with varying concentrations ranging from 20 to 100 ppm. This research aims to explore the prospective utilization of coffee waste as an inhibitory agent that can be reutilized for diverse purposes. Moreover, the extraction process in this work is done by using only water extraction. Measurements of weight loss and hydrogen evaluation methods (HEM) showed that the corrosion rate of carbon steel decreased by raising the CE inhibitor concentration. Electrochemical impedance spectroscopy (EIS) confirmed decreasing the capacitance of double-layer Cdl values due to increasing the amount of the inhibitor in the system. The observed reduction in capacitance Cdl is attributed to increasing the width of the electrical double layer. This indicates that the inhibitor particles work through sorption at the contact of the acid solution and carbon steel. Results of the polarization test determined CE act as an inhibitor of mixed types. This causes a reduction in anodic and cathodic reactions of carbon steel in 0.5 M HCl. All the results of the above experiments assure the productivity of the extract enhanced by increasing the extract dosage, science the initial efficiency (IE) was equal to 76% at 20 ppm and reached 96% at 100 ppm.

Nano zero-valent iron (nZVI), bimetallic nano zero-valent iron-copper (Fe0– Cu), and fava bean activated carbon-supported bimetallic nano zero-valent iron-copper (AC-Fe0-Cu) are synthesized and characterized using DLS, zeta potential, FT-IR, XRD, and SEM. The maximum removal capacity is demonstrated by bimetallic Fe0–Cu, which is estimated at 413.98 mg/g capacity at pH 7, 180 min of contact duration, 120 rpm shaking speed, ambient temperature, 100 ppm of C.V. dye solution, and 1 g/l dosage. The elimination capability of the H2SO4 chemical AC-Fe0-Cu adsorbent is 415.32 mg/g under the same conditions but with a 150 ppm C.V. dye solution. The H3PO4 chemical AC-Fe0-Cu adsorbent achieves a removal capacity of 413.98 mg/g under the same conditions with a 350 ppm C.V. dye solution and a 1.5 g/l dosage. Optimal conditions for maximum removal efficiency are determined by varying pH (3–9), time intervals (15–180 min), and initial dye concentrations (25–1000 ppm). Kinetic and isothermal models are used to fit the results of time and concentration experiments. The intra-particle model yields the best fit for bimetallic Fe0–Cu, H2SO4 chemical AC- Fe0–Cu, and H3PO4 chemical AC-Fe0-Cu, with corrected R-Squared values of 0.9656, 0.9926, and 0.964, respectively. The isothermal results emphasize the significance of physisorption and chemisorption in concentration outcomes. Response surface methodology (RSM) and artificial neural networks (ANN) are employed to optimize the removal efficiency. RSM models the efficiency and facilitates numerical optimization, while the ANN model is optimized using the moth search algorithm (MSA) for optimal results.

Activated carbon is a promising material with high efficiency in dye removal from polluted wastewater. However, commercial activated carbon is expensive and generates black color in the medium. Therefore, searching for low-cost, eco-friendly activated carbon sources such as agricultural wastes and algal biomasses is essential. Hence, this study is directed to prepare the physical and the H3PO4 chemical activated carbon from the algae ”Sargassum dent folium” and the raw algae itself and apply it for Methyl Orange (M. orange) removal from contaminated wastewater and compare its performance with the commercial activated carbon. First, adsorbent materials are prepared and involved in the optimization process for M. orange removal using some preliminary experiments, followed by Response Surface Method-ology (RSM) and Artificial Neural Network (ANN). Finally, Isotherm and kinetics are studied to explain the adsorption mechanism. In contrast to other materials, results show that physical algae-activated carbon achieves the maximum removal efficiency of 96.687%. These results are obtained from ANN combined with Moth Search Algorithm (MSA), representing the most effective model for achieving the highest M. orange removal efficiency from Physical algae activated carbon. In the algae case, the best experimental and predicted removal efficiencies are 85.9407 RE%, 88.5 indicated RSM RE%, and 85.9431 predicted ANN RE%. The best observed and predicted removal efficiencies for the H3PO4 chemical activated carbon are 89.6157 RE%, 82.38 predicted RSM RE%, and 89.5442 predicted ANN RE%. The best experimental and predicted removal efficiencies for the physical-activated carbon are 94.7935 RE%, 95.49 indicated RSM RE%, and 95.4298 predicted ANN RE%. The best observed and predicted removal efficiencies for the commercial-activated carbon are 92.2659 RE%, 96.65 predicted RSM RE%, and 92.2658 predicted ANN RE%. In the algae case, the best experimental and predicted removal efficiencies are 85.9407 %RE, 88.5 predicted RSM RE %, and 85.9431 expected ANN RE%. For the H3PO4 chemical activated carbon, the best experimental and predicted removal efficiencies are 89.6157%RE, 82.38 indicated RSM RE%, and 89.5442 predicted ANN RE%. For the physical-activated carbon, the best observed and predicted removal efficiencies are 94.7935 %RE, 95.49 predicted RSM RE%, and 95.4298 indicated ANN RE%. For the commercial-activated carbon, the best experimental and predicted removal efficiencies are 92.2659 %RE, 96.65 predicted RSM RE%, and 92.2658 predicted ANN RE%. This study intends to treat industrial wastewater contaminated with the anionic M. orange dye using raw algae and their generated activated carbon (physical and chemical forms), which are economical. It then compares the results to the effectiveness of commercial activated carbon. In the state of the raw algae, Temkin and Langmuir isotherm models best suit the data, while Temkin agrees well with the data from physical-activated carbon. Temkin and Freundlich's models are fitted with the H3PO4 chemical activated carbon. The model that fits the raw algae physically activated carbon and H3PO4 chemical-activated carbon the best is pseudo-second-order kinetics. Future research could examine the produced activated carbon-based algae's capacity to extract more contaminants from contaminated wastewater. This study intends to treat industrial wastewater contaminated with the anionic M. orange dye using raw algae and their generated activated carbon (physical and chemical forms), which are economical. It next compares the results to the effectiveness of commercial activated carbon.

The textile industry is considered a source of pollution because of the discharge of dye wastewater. The dye wastewater effluent has a significant impact on the aquatic environment. According to the World Bank, textile dyeing, and treatment contribute 17 to 20% of the pollution of water. This paper aims to prepare the bimetallic nano zero-valent iron-copper (Fe ^0 -Cu), algae-activated carbon, and their composites (AC-Fe ^0 -Cu), which are employed as adsorbents. In this paper, Synthetic adsorbents are prepared and examined for the adsorption and removal of soluble cationic crystal violet (CV) dye. The influence of synthetic adsorbents on the adsorption and removal of soluble cationic crystal violet (CV) dye is investigated using UV-V spectroscopy at different pH (3–10), time intervals (15–180) min, and initial dye concentrations (50–500 ppm). Raw algae exhibit an impressive 96.64% removal efficiency under the following conditions: pH 7, contact time of 180 min, rotational speed of 120 rpm, temperature range of 25 °C–30 °C, concentration of 300 ppm in the CV dye solution, and a dose of 4 g l ^−1 of raw algae adsorbent. The best removal efficiencies of Raw algae Fe ^0 -Cu, and H _3 PO _4 chemical AC-Fe ^0 -Cu are 97.61 % and 97.46 %, respectively, at pH = 7, contact time = 150 min, rotational speed = 120 rpm, T = (25–30) °C, concentration = 75 ppm of CV dye solution, and 1.5 g l ^−1 doses of raw algae F e0-Cu adsorbent and 1 g l ^−1 dose of H _3 PO _4 chemical AC-Fe ^0 -Cu adsorbent. The maximum amounts ( q _max ) of Bi-RA and RA adsorbed for the adsorption process of CV are 85.92 mg g ^−1 and 1388 mg g ^−1 , respectively. The Bi-H _3 A-AC model, optimized using PSO, demonstrates superior performance, with the highest adsorption capacity estimated at 83.51 mg g ^−1 . However, the Langmuir model predicts a maximum adsorption capacity ( q _e ) of 275.6 mg g ^−1 for the CV adsorption process when utilizing Bi-H _3 A-AC. Kinetic and isothermal models are used to fit the data of time and concentration experiments. DLS, zeta potential, FT-IR, XRD, and SEM are used to characterize the prepared materials. Response surface methodology (RSM) is used to model the removal efficiency and then turned into a numerical optimization approach to determine the ideal conditions for improving removal efficiency. An artificial neural network (ANN) is also used to model the removal efficiency.

The discharge of effluents from dye industries into water streams poses a significant environmental and public health risk. In response, eco-friendly adsorbents derived from agricultural waste, such as Fava Bean Peels (R–FBP), have been investigated as potential materials for the removal of such pollutants. In this study, R–FBP and their corresponding physical and chemically activated carbon (P-RFB-AC and C-FBP-AC) were synthesized using H3PO4 acid and characterized using FT-IR, and SEM analyses. An optimization process was conducted to determine the optimum conditions for achieving high Methyl Orange (M. Orange) removal efficiencies using the prepared materials, namely R–FBP, P-RFB-AC, and C-FBP-AC. The adsorption mechanism was examined by analyzing the isotherm and kinetics. The results revealed that the physical raw-activated carbon exhibited the highest removal efficiency of 96.8% compared to other materials. This outcome was achieved through the use of ANN combined with Moth Search Algorithm (MSA), which was found to be the most effective model for achieving the highest M. Orange removal efficiency from Physical raw fava bean activated carbon. Under parameters of 1000 mg/l M. Orange concentration, 2 g/l dose, 15 min contact time, and 120 rpm shaking, the best experimental and predicted removal efficiencies for physical-activated carbon fava bean rind were 96.8 RE%, 96.01 indicated RSM RE%, and 95.75 predicted ANN RE%. The highest experimental and predicted removal efficiencies for the H3PO4 chemical activated carbon fava bean peel were 94%RE. This study aimed to develop an economical solution for treating industrial wastewater contaminated with anionic M. Orange dye using raw fava bean peel and their generated activated carbon, in both physical and chemical forms. The Temkin and Langmuir isotherm models were found to best fit the data for raw fava bean peel, while Temkin agreed well with the data from physical-activated carbon. Temkin and Freundlich's models were fitted with the H3PO4 chemical activated carbon. Pseudo-second-order kinetics was identified as the most suitable model for both physically and chemically activated carbons. Future research may explore the capacity of the produced activated carbon-based algae to extract a wider range of contaminants from contaminated wastewater. In summary, this work contributes to the development of eco-friendly and cost-effective methods for removing dyes, specifically M. Orange, from industrial effluents. By synthesizing and characterizing R–FBP and their relative activated carbon, the adsorption mechanism was studied, and the optimum conditions for achieving high M. Orange removal efficiencies were determined. The results showed that physical raw-activated carbon exhibited the highest removal efficiency, and pseudo-second-order kinetics was the most suitable model for both physically and chemically activated carbon.

The textile business is one of the most hazardous industries since it produces several chemicals, such as dyes, which are released into water streams with ef-fluents. For the survival of the planet's life and the advancement of humanity, water is a crucial resource. One of the anthropogenic activities that pollute and consume water is the textile industry. Thus, the purpose of the current effort is to Apply coagulation as a Physico-chemical and biological treatment strat-egy with different techniques and mechanisms to treat the effluent streams of textile industries. The discharge of these effluents has a negative impact on the environment, marine life, and human health. Therefore, the treatment of these effluents before discharging is an important matter to reduce their adverse ef-fect. Many physico-chemical and biological treatment strategies for contaminants removal from polluted wastewater have been proposed. Coagulation is thought to be one of the most promising physico-chemical strategies for removing con-taminants and colouring pollutants from contaminated water. Coagulation is accompanied by a floculation process to aid precipitation, as well as the collection of the created sludge following the treatment phase.. Different commercial, and natural coagulants have been applied as a coagulants in the process of coagulation. Additionally, many factors such as; pH, coagulant dose, pollu-tants concentration are optimized to obtain high coagulants removal capacity. This review will discuss the coagulation process, coagulant types and aids in addition to the factors affecting the coagulation process. Additionally, a brief comparison between the coagulation process, and the other processes; princi-ple, advantages, disadvantages, and their efficiency were discussed throgh the review. Furthermore, it discusses the models and optimization techniques used for the coagulation process including response surface methodology (RSM), ar-tificial neural network (ANN), and several metaheuristic algorithms combined with ANN and RSM for optimization in previous work. The ANN model has more accurate results than RSM. The ANN combined with genetic algorithm gives an accurate predicted optimum solution.

Water contamination with colours and heavy metals from textile effluents has harmed the ecology and food chain, with mutagenic and carcinogenic effects on human health. As a result, removing these harmful chemicals is critical for the environment and human health. Various standard physicochemical and biological treatment technologies are used; however, there are still some difficulties. Adsorption is described as a highly successful technology for removing contaminants from textile-effluents wastewater compared to other methods. Several adsorbent materials, including nanomaterials, natural materials, and biological biomasses, are identified as effective adsorbents for textile effluents. Activated carbon preparation from these different adsorbents is an excellent pre-treatment to remove the adsorption capacity. Therefore, through this study various adsorbent types, especially activated carbon adsorbents will be discussed in addition to the factors affecting adsorption and models applied for optimising the adsorption process.

Nano zero-valent iron (nZVI), bimetallic Nano zero-valent iron-copper (Fe0- Cu), and fava bean activated carbon-supported with bimetallic Nano zero-valent iron-copper (AC-F e0-Cu) were prepared and characterized by DLS, FT-IR, XRD, and SEM. The influence of the synthesized adsorbents on the adsorption and removal of soluble anionic methyl orange (M.O) dye was investigated using UV-V spectroscopy. The influence of numerous operational parameters was studied at varied pH (3–9), time intervals (15–180 min), and dye concentrations (25–1000 ppm) to establish the best removal conditions. The maximum removal efficiency of M.O. using the prepared adsorbent materials reached about 99%. The removal efficiency is modeled using response surface methodology (RSM). The Bimetallic F e 0 -Cu, the best experimental and predicted removal efficiency is 96.8% RE. For the H2SO4 chemical AC- F e 0 -Cu, the best experimental and removal efficiency is 96.25% RE. The commercial AC-Fe0–Cu, the best experimental and predicted removal efficiency is 94.93%RE. This study aims to produce low-cost adsorbents such as Bimetallic Fe0-Cu, and Fava Bean Activated Carbon-Supported Bimetallic AC-Fe0-Cu to treat the industrial wastewater from the anionic methyl orange (M.O) dye and illustrate its ability to compete H2SO4 chemical AC-Fe0-Cu, and commercial AC-Fe0-Cu. [ABSTRACT FROM AUTHOR]