Search

Abstract Nanoporous Pt films fabricated by oblique angle deposition hold potential as electrocatalysts in various energy-related fields owing to their high surface area, structural stability, and adequate conductivity. In this study, we investigated the morphology, porosity, and electrical conductivity of nanoporous Pt thin films and systematically studied their interrelationships. Specifically, we revealed an in-plane anisotropy in the electrical conductivity that correlates with the surface morphology of the film. This anisotropy was evident in the resistance measurements along the in-plane lateral and vertical directions, which aligned well with our simple model. The results emphasize the significance of film morphology in determining the film’s electrical properties. This study contributes to the understanding of the physical properties of Pt films fabricated via oblique angle deposition and offers valuable insights for designing nanoporous films for various applications.

This study was designed to determine the characteristics and tendencies of drones, which have emerged as a key weapon system in the Russian-Ukrainian War since 2022, and their use in modern warfare. A spatiotemporal analysis was conducted on 5,491 coordinates of drone-based battles within the city with a multidimensional model. The analysis revealed extensive drone operations by both Russia and Ukraine, with Ukraine shifting to offensive actions in 2023, and distinct temporal patterns by day of the week at battle sites, as indicated by the frequency of drone-based battles. Moreover, Russia maintained the momentum of offensive drone operations, intercepting 85.1% of Ukrainian drones and achieving a 54.0% success rate in drone-based attacks, whereas Ukraine intercepted 43.3% of Russian drones, with a success rate of only 14.3%. Based on this study, the spatiotemporal analysis of drone-based combat across Ukraine enabled an examination of the operating areas, roles, and efficiency of this weapon system as well as an understanding of the impact and multifaceted characteristics associated with its deployment on the battlefield.

Abstract The advantageous role of 2D electron gas presence at the AlGaN/GaN interface attracts huge interest in the field of GaN‐based ultraviolet photodetector technology. However, the presence of high dark current deteriorates the photodetector performance by diminishing several figures of merit. In this work, enhanced figures of merit are demonstrated by employing interdigitated p‐GaN finger structure on the top of the AlGaN/GaN heterostructure. The commonly present high dark current in p‐GaN/AlGaN/GaN planar photodetector is largely reduced (from ≈µA to few pA) by etching the p‐GaN, excluding the electrode region. Furthermore, by using a graphene transparent electrode along with the p‐GaN interdigitated fingers on AlGaN/GaN heterostructure, ultraviolet photodetectors with superior sensitivity (3.55 × 106) and ultrahigh detectivity (1.91 × 1014 cm Hz1/2 W−1) are realized at 360 nm. A comparison of graphene/p‐GaN and Ni/Au/p‐GaN interdigitated fingers and planar p‐GaN (with interdigitated graphene contacts) all on AlGaN/GaN heterostructure allows to understand the dominant roles of electrode transparency and the heterojunction structure. The simple and high electron mobility transistor‐compatible fabrication process of UV detectors provides a unique application in the field of UV sensing technology.

Abstract A dual-functional ultraviolet (UV) photodetector with a large UV-to-visible rejection ratio is presented, in which interdigitated finger-type two-dimensional graphene electrodes are introduced to an AlGaN/GaN heterostructure. Two photocurrent generation mechanisms of photovoltaic and photoconductive dominances coexist in the device. The dominance of the mechanisms changes with the induced bias voltage. Below a threshold voltage, the device showed fairly low responsivities but fast response times, as well as a constant photocurrent against the induced bias. However, the opposite characteristics appeared with high bias voltage. Specifically, above the threshold voltage, the device showed high responsivities with additional gain, but slow rise and recovery times. For instance, the responsivity of 10.9 A/W was observed with the gain of 760 at the induced bias voltage of 5 V. This unique multifunctionality enabled by the combination of an AlGaN/GaN heterostructure with graphene electrodes facilitates the development of a single device that can achieve multiple purposes of photodetection.

We present a 640 × 480 CMOS image sensor (CIS) with in-circuit bi-directional gamma correction with a proposed digital-correlated double sampling (CDS) structure. To operate the gamma correction in the CIS, the transfer function of the analog-to-digital converter can be changed by controlling the clock frequency of the counter using analog CDS. However, the analog CDS is vulnerable to capacitor mismatch, clock feedthrough, etc. Therefore, we propose a digital-CDS method with a hold-and-go counter structure to operate the bi-directional gamma correction in the CIS. The proposed CIS achieves a 10-bit resolution using a global log-exponential counter and configurable column reset counter with a resolution of 8/9 bits. The sensor was fabricated in a 0.11 μm CIS process, and the full chip area was 5.9 mm × 5.24 mm. The measurement results showed a maximum SNR improvement of 10.41% with the proposed bi-directional gamma-corrected digital-CDS with the hold-and-go counter. The total power consumption was 6.3 mW at a rate of 16.6 frames per second with analog, pixel, and digital supply voltages of 3.3 V, 3.3 V, and 1.5 V, respectively.

Solar-blind deep-ultraviolet (UV) photodetectors (PDs) with high responsivity and fast response have attracted significant attention in environmental, industrial, biological, and military applications. AlGaN is a representative semiconductor material in the field of solar-blind detection; semiconductor performance can be accelerated by combining it with high-transparency, high-stability contact electrode materials. In this study, solar-blind deep-UV metal–semiconductor–metal (MSM) PDs were fabricated based on two-dimensional reduced graphene oxide (rGO) contacts formed on various high-Al-content AlGaN semiconductors. A low dark current in the order of a few picoamperes and a fast photoresponse time of a few tens of milliseconds were confirmed. The investigation of the effects of front- and back-side illumination showed that the photocurrents and corresponding responsivities of the PDs drastically improved under back-side illumination. In detail, the peak locations of the responsivity–wavelength curves were downshifted from 290 nm with a responsivity of 0.0518 A/W for the rGO/Al0.5Ga0.5N MSM PD to 250 nm with a responsivity of 0.0113 A/W for the rGO/Al0.7Ga0.3N MSM PD under back-side illumination. These results indicate that rGO contacts on AlGaN provide a viable approach for developing solar-blind deep-UV PDs.

A graphene Schottky contact was fabricated on an AlGaN/GaN heterostructure and subsequently analyzed. The calculated and experimentally measured Schottky barrier heights (SBHs) determined using the theoretical Schottky–Mott model, the thermionic emission model, the temperature-dependent current–voltage measurement, and the capacitance–voltage measurement were observed to be inconsistent, which was attributed to the ambiguities in both the Schottky contact area and the Richardson constant. While excluding the effects of these two factors, an SBH of 0.15 eV was determined by the temperature-dependent Richardson plot. This result was confirmed by calculating the inverse of the square of the measured capacitance with consideration of the threshold voltage required to deplete the two-dimensional electron gas under the Schottky contact.

The junction temperature, one of the major parameters that strongly affect the performance of light-emitting diodes (LEDs), increases during operation because of the power dissipated as heat within an LED device. Therefore, LED devices with poor characteristics are expected to have higher junction temperatures for the same driving conditions. In this study, an observation contrary to this expectation is presented: a deep-ultraviolet LED device with superior electrical characteristics shows a higher junction temperature at the same input electrical power than a device with poor characteristics. A simple equivalent circuit comprising a diode, a series resistor, and shunt components is employed to elucidate this counter-intuitive observation by considering the possible heat sources inside the LED device. It is found that the junction temperature is mainly dominated by the power dissipated at the diode instead of the other possible heat sources including the Joule heating effect of the resistive components.

As the next-generation display technology, microscale light-emitting diode (μ-LED) displays have attracted significant attention recently. For applying μ-LEDs as direct emissive pixels in everyday display applications, many chips in a relatively small-sized wafer must be relocated and distributed quickly over a wide screen area via so-called transfer technology. After a brief review of current conventional transfer technologies for placing μ-LEDs on a wide screen, for perspective, a new and versatile delivery technique for μ-LEDs is presented, in which an LED chip is converted to a ball shape in order to facilitate handling and processing of μ-LEDs for practical applications. Plausible procedures including the formation, arrangement, and removal of the plastic ball are discussed to envision potential impacts of the technology.

High orthodontic forces and various directions of applied forces can be associated with loosening of the screw anchorage in the bone. Screw designs have been modified to increase the stability of the miniscrews. This research evaluates the influence of three-designs on the stability of orthodontic miniscrews. A conventionally cylinder-type miniscrew design (Bio-Action screw, Jin-Biomed co., Bucheon, Korea) was set as a control, and three conditions were studied based on modifications of this control design. Condition-1 has narrowed threads in the upper part of the screw; Condition-2 has a notch at the middle part; and Condition-3 has the combination of Condition-1 and Condition-2. The moment required to unwind the miniscrew to five degrees is tested, and the moment generated at the cortical bone and the trabecular bone were calculated with finite element analysis. Compared to the control, all three conditions showed a higher moment required to unwind the miniscrew and a higher moment generated at the cortical bone. At the trabecular bone, condition-2 and -3 showed higher moment than the control, and condition-1 showed similar moment to the control. Condition-3 required a higher overall moment to unwind the miniscrew. These findings validate the design modifications used to increase the rotational resistance.

Dielectric layers prepared by different deposition methods were used for the surface passivation of AlGaN/GaN heterostructure field-effect transistors (HFETs) and the corresponding electrical characteristics were examined. Increases in the sheet charge density and the maximum drain current by approximately 45% and 28%, respectively, were observed after the deposition of a 100 nm-thick SiO2 layer by plasma-enhanced chemical vapor deposition (PECVD) on the top of the AlGaN/GaN HFETs. However, SiO2 deposited by a radio frequency (rf) sputter system had the opposite effect. As the strain applied to AlGaN was influenced by the deposition methods used for the dielectric layers, the carrier transport in the two-dimensional electron gas formed at the interface between AlGaN and GaN was affected accordingly.

The current transport mechanism of graphene formed on AlxGa1−xN/GaN heterostructures with various Al mole fractions (x = 0.15, 0.20, 0.30, and 0.40) is investigated. The current–voltage measurement from graphene to AlGaN/GaN shows an excellent rectifying property. The extracted Schottky barrier height of the graphene/AlGaN/GaN contacts increases with the Al mole fraction in AlGaN. However, the current transport mechanism deviates from the Schottky-Mott theory owing to the deterioration of AlGaN crystal quality at high Al mole fractions confirmed by reverse leakage current measurement.

AlGaN semiconductors are promising materials in the field of ultraviolet (UV) detection. We fabricated AlGaN/GaN UV metal⁻semiconductor⁻metal (MSM) photodiodes with two back-to-back interdigitated finger electrodes comprising reduced graphene oxide (rGO). The rGO showed high transparency below the wavelength of 380 nm, which is necessary for a visible-blind photodetector, and showed outstanding Schottky behavior on AlGaN. As the photocurrent, dark current, photoresponsivity, detectivity, and cut-off wavelength were investigated with the rGO/AlGaN MSM photodiodes with various Al mole fractions, systematic variations in the device characteristics with the Al mole fraction were confirmed, proving the potential utility of the device architecture combining two-dimensional materials, rGO, and nitride semiconductors.

The effect of strongly-imbalanced carrier concentration and mobility on efficiency droop is studied by comparing the onset voltage of high injection, the onset current density of the droop, and the magnitude of the droop, as well as their temperature dependence, of GaInN-based blue and green light-emitting diodes (LEDs). An n-to-p asymmetry factor is defined as σn/σp, and was found to be 17.1 for blue LEDs and 50.1 for green LEDs. Green LEDs, when compared to blue LEDs, were shown to enter the high-injection regime at a lower voltage, which is attributed to their less favorable p-type transport characteristics. Green LEDs, with lower hole concentration and mobility, have a lower onset current density of the efficiency droop and a higher magnitude of the efficiency droop when compared to blue LEDs. The experimental results are in quantitative agreement with the imbalanced carrier transport causing the efficiency droop, thus providing guidance for alleviating the phenomenon of efficiency droop.

The dependence of the polarization-induced electric field in GaInN/GaN multiple-quantum-well light-emitting diodes (LEDs) on the GaN quantum barrier (QB) thickness is investigated. Electrostatic arguments and simulations predict that a thin QB thickness reduces the electric field in the quantum wells (QWs) and also improves the LED efficiency. We experimentally demonstrate that the QW electric field decreases with decreasing QB thickness. The lower electric field results in a better overlap of electron and hole wave functions and better carrier confinement in the QWs. A reduced efficiency droop and enhanced internal quantum efficiency is demonstrated for GaInN/GaN LEDs when the QB thickness is reduced from 24.5 to 9.1 nm.