Search

This study was designed to observe the length dependence of a well-molded fiberglass body cast attached to a halo on motion restriction in an unstable cadaveric cervical spine. Also, by using this technique, comparison between the immobilization provided by a body cast and that provided by a standard premolded polyethylene halo vest could be made. Extreme cervical instability was created on adult cadavers. A halo ring was applied and then attached to a fiberglass body cast or to a polyethylene halo vest. Sequential lateral cervical radiographs were obtained during maximum flexion as the body cast was shortened from the level of the iliac crests to the level of the xiphoid process. Radiographic motion was also assessed within the polyethylene halo vest. Results revealed minimal motion difference as the fiberglass body cast was sequentially shortened. In contrast, motions within the polyethylene halo vest were variable. These results suggest that cervical immobilization may be relatively independent of support structure length and that immobilization can be maintained by a well-fitting halo vest extending to the level of the xiphoid process.

Peripheral nerves are often mechanically stretched in association with trauma to extremities, resulting in varying degrees of impairment of nerve function. However, little is known about the biomechanical properties of peripheral nerves and limits of stretching that the nerve may undergo before structural changes occur. Also, the injury pattern of nerves under stretching is poorly understood. In the present study, fresh rabbit tibial nerves (n = 18) were harvested. Nine nerves were stretched to failure in an INSTRON materials testing machine at a rate of 1 cm/min (strain rate of 0.5%/s). Load-deformation and stress-strain curves were determined. Histological examination by light microscopy of the stretched nerves as well as six normal control nerves and three clamped nonstretched control nerves was performed. The results show that the rabbit tibial nerves have an in situ strain of 11.0 +/- 1.5% and exhibit a nonlinear stress-strain relationship. After 20% strain, the curve becomes linear up to failure. The ultimate strain and tensile strength of the nerves were 38.5 +/- 2.0% and 11.7 +/- 0.7 MPa, respectively. At failure, the load dropped suddenly, but the specimens remained grossly intact. Histological analysis of the stretched nerves showed multiple ruptures of perineurial sheaths when compared to controls.

This study was designed to observe the length dependence of a well-molded fiberglass body cast attached to a halo on motion restriction in an unstable cadaveric cervical spine. Also, by using this technique, comparison between the immobilization provided by a body cast and that provided by a standard premolded polyethylene halo vest could be made. Extreme cervical instability was created on adult cadavers. A halo ring was applied and then attached to a fiberglass body cast or to a polyethylene halo vest. Sequential lateral cervical radiographs were obtained during maximum flexion as the body cast was shortened from the level of the iliac crests to the level of the xiphoid process. Radiographic motion was also assessed within the polyethylene halo vest. Results revealed minimal motion difference as the fiberglass body cast was sequentially shortened. In contrast, motions within the polyethylene halo vest were variable. These results suggest that cervical immobilization may be relatively independent of support structure length and that immobilization can be maintained by a well-fitting halo vest extending to the level of the xiphoid process.

Optimal insertion of halo fixation pins to maximize the rigidity of the interface between the halo pins and the outer table of the skull is important in reducing the incidence of pin loosening. An in vitro biomechanical study was performed using cadaver skulls to investigate the effects of pin location on the rigidity of this pin-bone interface. Halo pins were inserted at nine positions within a recommended "safe zone" for pin insertion. It was found that the rigidity of the pin-bone interface progressively decreased as pins were inserted more superiorly on the calvaria. The rigidity of the interface did not change significantly when the location of the pins was varied in the horizontal axis. This reduction in interface rigidity associated with inserting pins more superiorly on the skull may be related to an increase in the angle of insertion of the pins with respect to the surface of the calvaria. Based on this study, a change in the technique of halo pin insertion is recommended. Pins should be placed as inferiorly as possible, close to the supraorbital ridge, to achieve the most perpendicular angle of insertion and thus the most rigid fixation. The improved rigidity obtained with perpendicular pin insertion may minimize the rate of pin loosening and other complications associated with use of the halo orthosis.

This study evaluated the effect of angled insertion of halo pins on the biomechanical characteristics of the halo pin-calvarium complex. Halo pins were inserted into isolated calvarium sections at 90 degrees, 75 degrees, and 60 degrees to the surface of the bone at an insertional torque of 0.68 N-m (6 inch-pounds). Initial rigidity, load at failure, and deformation at failure of the pin-bone complex were assessed during transverse shear loading. The structural properties of the pin-bone complex were maximized at loads approaching failure when pins were inserted perpendicular (90 degrees) to the bony surface and significantly decreased at more acute angles of insertion. Perpendicular insertion of halo pins maximizes the structural properties of the complex formed by the halo pin and the calvarium. This improved structural behavior may minimize the incidence of pin loosening clinically, and may reduce the frequency of other complications currently associated with the use of the halo orthosis.

Osteomyelitis and intracranial abscess are among the most serious complications that have been reported in association with the use of the halo device. The cases of five patients who had formation of an intracranial abscess related to the use of a halo cervical immobilizer are described. All of the infections resolved after drainage of the abscess, debridement, and parenteral administration of antibiotics. Meticulous care of the pin sites is essential to avoid this serious complication. Additionally, since all of the infections were associated with prolonged halo-skeletal traction, this technique should be used with caution and with an awareness of the possible increased risks of pin-site infection and of formation of a subdural abscess.

Osteomyelitis and intracranial abscess are among the most serious complications that have been reported in association with the use of the halo device. The cases of five patients who had formation of an intracranial abscess related to the use of a halo cervical immobilizer are described. All of the infections resolved after drainage of the abscess, débridement, and parenteral administration of antibiotics. Meticulous care of the pin sites is essential to avoid this serious complication. Additionally, since all of the infections were associated with prolonged halo-skeletal traction, this technique should be used with caution and with an awareness of the possible increased risks of pin-site infection and of formation of a subdural abscess.