Search

The current work focuses on utilization of ANN (artificial neural network) for the prediction of performance and tailpipe emissions of Garcinia gummigutta methyl ester (GGME) enriched with H 2 and TiO 2 nano additives. For experimentation, H 2 gas was introduced to the mixes containing TiO 2 nanoparticles. Diesel, B10 blend (10% GGME biofuel + 90% Diesel), B20 (20% GGME biofuel + 80% Diesel), Diesel-TiO 2 (Mineral Diesel with 100 ppm TiO 2 nano additives), B10-H 2 -TiO 2 (B10 blend with 100 ppm nano additives + 5 L/min of H 2 ) and B20-H 2 -TiO 2 (B20 blend with 100 ppm nanoparticles + 5 L/min of H 2 ) were considered for experimentation. A constant mass flow rate of 10 L/min was used for the hydrogen flow throughout the test procedures. Test results were carefully analyzed to determine the performance and emission measures. Different speeds between 1800 and 2800 rpm were used for each test. When combined with pure Diesel and mixtures of biodiesel, these nanoparticles and hydrogen enhanced the performance data. For instance, the brake-specific fuel consumption was reduced but the power, torque, and thermal efficiency were increased. Although there was a modest rise in NO emissions, the primary goal of lowering CO, CO 2 , and other UHC emissions was met. The ANN models confirm and agreed the Diesel engine experimental work possesses minimal root mean square error (RMSE) and correlation coefficient values were estimated. This ideal model predicts and optimizes the engine output at a higher accuracy level, which gives better results compared with other empirical and theoretical models., Competing Interests: Declarations. Competing interests: The authors declare no competing interests., (© 2025. The Author(s).)

The study employed an Artificial Neural Network (ANN) to predict the performance and emissions of a single-cylinder SI engine using blends of Gasoline, Ethanol, and Methanol (GEM) ranging from E10 to E50 equivalence, achieving less than 5% error compared to experimental values. Furthermore, Response Surface Methodology (RSM) was utilized to optimize the engine's performance, identifying the optimal operating conditions of 2992.9 rpm engine speed and an E20-equivalent GEM blend. Under these conditions, the engine exhibited a brake thermal efficiency (B_The) of 34.63%, a brake specific fuel consumption (BSFC) of 243.7 g/kW-hr, and minimal emissions of 1.5% CO, 108.13 ppm HC, and 1211.8 ppm NO x , with an overall desirability of 0.820, indicating a highly favorable combination of performance and emissions characteristics., Competing Interests: Declarations. Competing interests: The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (© 2025. The Author(s).)

This study explores the integration of nanotechnology and Long Short-Term Memory (LSTM) machine learning algorithms to enhance the understanding and optimization of fuel spray dynamics in compression ignition (CI) engines with varying bowl geometries. The incorporation of nanotechnology, through the addition of nanoparticles to conventional fuels, improves fuel atomization, combustion efficiency, and emission control. Simultaneously, LSTM models are employed to analyze and predict the complex spray behavior under diverse operational and geometric conditions. Key parameters, including spray penetration, droplet size distribution, and evaporation rates, are modeled and validated against experimental data. The findings reveal that nanoparticle-enhanced fuels, coupled with LSTM-based predictive analytics, lead to superior combustion performance and lower pollutant formation. This interdisciplinary approach provides a robust framework for designing next-generation CI engines with improved efficiency and sustainability. Diesel engine performance and emissions were found to be influenced by variations in combustion chamber geometry, underwent validation through simulation using Diesel-RK. Re-entrant bowl profile in quaternary blend is found to exhibit 31.3% higher BTE and 8.65% lowered BSFC than the conventional HCC bowl at full load condition. Emission wise, re-entrant bowl induced 90.16% lowered CO, 59.95% lowered HC and 15.48% lowered smoke owing to improved spray penetration and faster burning of soot precursors. However, the NO x emissions of DBOPN-TRCC were found to be higher. The simulation outcomes, derived from Diesel-RK, were subsequently compared with empirical data obtained from real-world experiments. These experiments were systematically carried out under identical operating conditions, employing different piston bowl geometries., Competing Interests: Declarations. Competing interests: The authors declare no competing interests., (© 2024. The Author(s).)

The microgrid (MG) faces significant security issues due to the two-way power and information flow. Integrating an Energy Management System (EMS) to balance energy supply and demand in Malaysian microgrids, this study designs a Fuzzy Logic Controller (FLC) that considers intermittent renewable sources and fluctuating demand patterns. FLC offers a flexible solution to energy scheduling effectively assessed by MATLAB/Simulink simulations. The microgrid consists of PV, battery, grid, and load. A Maximum Power Point Tracking (MPPT) controller helps to extract the maximum PV output and manages the power storage by providing or absorbing excess power. System analysis is performed by observing the State of Charge (SoC)of the battery and output power for each source. The grid supplies additional power if the battery and PV fail to meet the load demand. Total Harmonic Distortion (THD) analysis compares the performance of the Proportional-Integral Controller (PIC) and FLC. The results show that the PI controller design reduces the THD in the current signal, while FLC does not reduce the THD of the grid current when used in the EMS. However, FLC offers better control over the battery's SOC, effectively preventing overcharging and over-discharging. While PI reduces THD, FLC provides superior SOC control in a system comprising PV, battery, grid, and load. The findings demonstrate that the output current is zero when the SOC is higher than 80% or lower than 20%, signifying that no charging or discharging takes place to avoid overcharging and over-discharging. The third goal was accomplished by comparing and confirming that the grid current's THD for the EMS designed with both the PI Controller and the FLC is maintained below 5%, following the IEEE 519 harmonic standard, using the THD block in MATLAB Simulink. This analysis highlights FLC's potential to address demand-supply mismatches and renewable energy variability, which is crucial for optimizing microgrid performance., Competing Interests: Declarations. Competing interests: The authors declare no competing interests., (© 2025. The Author(s).)

Nature's evolutionary mastery has perfected design over the years, yielding organisms superbly adapted to their surroundings. This research delves into the promising domain of bio-inspired designs, poised to revolutionize mechanical engineering. Leveraging insights drawn from prior conversations, we categorize innovations influenced by life on land, in water, and through the air, emphasizing their pivotal contributions to mechanical properties. Our comprehensive review reveals a wealth of bio-inspired designs that have already made substantial inroads in mechanical engineering. From avian-inspired lightweight yet robust materials to hydrodynamically optimized forms borrowed from marine creatures, these innovations hold immense potential for enhancing mechanical systems. In conclusion, this study underscores the transformative potential of bio-inspired designs, offering improved mechanical characteristics and the promise of sustainability and efficiency across a broad spectrum of applications. This research envisions a future where bio-inspired designs shape the mechanical landscape, fostering a more harmonious coexistence between human technology and the natural world., Competing Interests: Conflict of interestThe authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (© King Abdulaziz City for Science and Technology 2024. Springer Nature or its licensor (e.g. a society or other partner) holds exclusive rights to this article under a publishing agreement with the author(s) or other rightsholder(s); author self-archiving of the accepted manuscript version of this article is solely governed by the terms of such publishing agreement and applicable law.)

This study investigates the erosion behavior of Al-SiC and Al-WC metal-based composites in a solid particle impingement environment developed through powder metallurgy. Micro-sized powders of SiC and WC were utilized in different weight proportions (0-10 wt%) for fabricating the composite samples. The angle of impingements of 30-90° and impact velocity of 30-90 m/s were used for solid particle erosion testing. Microstructure was characterized by XRD, SEM, and EDS. The results of the ANOVA test indicate that impact velocity is the most significant factor, followed by reinforcement content. SiC composite with reinforcement content of 2.5 and 5 wt% showed ductile erosion behavior at lower angles of impingements and brittle behavior at higher angles of impingements. On the other hand, 10 wt% of SiC indicated a semi-ductile erosion behavior. The reinforcement content is 5 and 10 wt % of WC showed a semi-ductile erosion behavior, whereas 2.5 wt% of WC showed a mix of ductile and brittle behavior. At a 30° angle of impingement, SiC (10 wt%) provides the best erosion performance, whereas, at 90° (i.e., at normal), WC (10 wt%) performs better than all other composites. SiC (5 wt %) comes out to be the best performer at 45° of the angle of impingement., Competing Interests: Competing interests: The authors declare no competing interests., (© 2024. The Author(s).)

Polyaniline-magnesia (PANI/MgO) composites with a fibrous nanostructure were synthesized via in situ oxidative polymerization, enabling uniform MgO integration into the polyaniline matrix. These composites were characterized using FTIR spectroscopy to analyze intermolecular bonding, XRD to assess crystallographic structure and phase purity, and SEM to examine surface morphology and topological features. The resulting PANI/MgO nanofibers were utilized to develop ammonia (NH 3 ) gas-sensing probes with evaluations conducted at room temperature. The study addresses the critical challenge of achieving high sensitivity and selectivity in ammonia detection at low concentrations, which is a problem that persists in many existing sensor technologies. The nanofibers demonstrated high selectivity and optimal sensitivity for ammonia detection, which was attributed to the synergistic effects between the polyaniline and MgO that enhance gas adsorption. Furthermore, the study revealed that the MgO content critically influences both the morphology and the sensing performance, with higher MgO concentrations improving sensor response. This work underscores the potential of PANI/MgO composites as efficient and selective ammonia sensors, highlighting the importance of MgO content in optimizing material properties for gas-sensing applications.

To address the global demand for sustainable energy, integrating biogas into internal combustion engines is becoming more important. Homogeneous Charge Compression Ignition (HCCI) engines, known for high efficiency and low emissions, offer a promising solution. This study investigates the optimal injector location for using biogas in HCCI engines, with diethyl ether (DEE) as the pilot fuel, evaluating three positions: (i) at the port, (ii) 6 cm away (Manifold 1), and (iii) 10 cm away (Manifold 2). Through experiments and simulations, the impact of injector location on engine performance is analyzed across various parameters, including methane fractions, engine loads, and exhaust gas compositions. Results show that port injection achieves the highest first law and exergy efficiencies but increases emissions of hydrocarbons (HC), carbon monoxide (CO), and smoke. At 15 Nm load, Manifold 1 shows a 27.34 % reduction in exergy efficiency compared to port injection, while Manifold 2 exhibits an 18.49 % decrease at higher loads. Despite lower efficiencies, Manifold 1 effectively reduces harmful emissions. The study also considers exergo-economic and sustainability aspects, highlighting that while port injection is optimal for efficiency, Manifold 1 excels in minimizing HC and CO emissions, with a 50 % reduction in HC and 71.43 % reduction in CO emissions at 15 Nm load compared to port injection. Manifold 2 achieves the lowest smoke emissions across all loads. This investigation provides crucial insights into optimizing HCCI engines for biogas utilization, emphasizing injector location, fuel composition, and operating parameters to enhance performance and reduce environmental impact., Competing Interests: The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (© 2024 The Authors.)

The electrochemical act of valve-regulated lead acid batteries can be enhanced by conductive materials like metal oxides. This work aims to examine the preparation and influence of zirconia on poly(vinyl alcohol) based gel valve-regulated lead acid battery. Characterizations like Fourier transform infrared spectroscopy, ionic conductivity, water retention study, cyclic voltammetry, electrochemical impedance spectroscopy and galvanostatic charge-discharge techniques were done. The optimized gel system exhibited a discharge capacity of 198.45 μAh cm -2  at the current density of 0.6 mA cm -2 . The battery cell with an optimized gel matrix displayed a maximum discharge capacity of 22.5 μAh at a current of 20 μA. After 500 continuous cycles, the battery attained a discharge capacity retention of 91 %. The presence of zirconia will increase the electrochemical performance of gel valve-regulated lead acid batteries., Competing Interests: The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (© 2024 The Authors.)

Integration of photovoltaic (PV) systems, desalination technologies, and Artificial Intelligence (AI) combined with Machine Learning (ML) has introduced a new era of remarkable research and innovation. This review article thoroughly examines the recent advancements in the field, focusing on the interplay between PV systems and water desalination within the framework of AI and ML applications, along with it analyses current research to identify significant patterns, obstacles, and prospects in this interdisciplinary field. Furthermore, review examines the incorporation of AI and ML methods in improving the performance of PV systems. This includes raising their efficiency, implementing predictive maintenance strategies, and enabling real-time monitoring. It also explores the transformative influence of intelligent algorithms on desalination techniques, specifically addressing concerns pertaining to energy usage, scalability, and environmental sustainability. This article provides a thorough analysis of the current literature, identifying areas where research is lacking and suggesting potential future avenues for investigation. These advancements have resulted in increased efficiency, decreased expenses, and improved sustainability of PV system. By utilizing artificial intelligence technologies, freshwater productivity can increase by 10 % and efficiency. This review offers significant and informative perspectives for researchers, engineers, and policymakers involved in renewable energy and water technology. It sheds light on the latest advancements in photovoltaic systems and desalination, which are facilitated by AI and ML. The review aims to guide towards a more sustainable and technologically advanced future., Competing Interests: We, the authors of this manuscript do not have any conflict of interest including any financial, personal or other relationships with other people or organizations within three years of beginning the submitted work that could inappropriately influence, or be perceived to influence, our work., (© 2024 The Authors.)

Emerging contaminants (ECs) are increasingly recognized as threats to human health and ecosystems. This review evaluates advanced analytical methods, particularly mass spectrometry, for detecting ECs and understanding their toxicity, transformation pathways, and environmental distribution. Our findings underscore the reliability of current techniques and the potential of upcoming methods. The adverse effects of ECs on aquatic life necessitate both in vitro and in vivo toxicity assessments. Evaluating the distribution and degradation of ECs reveals that they undergo physical, chemical, and biological transformations. Remediation strategies such as advanced oxidation, adsorption, and membrane bioreactors effectively treat EC-contaminated waters, with combinations of these techniques showing the highest efficacy. To minimize the impact of ECs, a proactive approach involving monitoring, regulations, and public education is vital. Future research should prioritize the refining of detection methods and formulation of robust policies for EC management., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2023 Elsevier Ltd. All rights reserved.)

In the realm of 3D printing, polymers serve as fundamental materials offering versatility to cater to a diverse array of final product properties and tailored to the specific needs of the creator. Polymers, as the building blocks of 3D printing, inherently possess certain mechanical and wear properties that may fall short of ideal. To address this limitation, the practice of reinforcing polymer matrices with suitable materials has become a common approach. One such reinforcement material is boron nitride (BN), lauded for its remarkable mechanical attributes. The integration of BN as a reinforcing element has yielded substantial enhancements in the properties of polylactic acid (PLA). The central objective of this research endeavor is the development of polymer composites based on PLA and fortified with boron nitride. This study undertakes the comprehensive exploration of the compatibility and synergy between BN and PLA with a keen focus on examining their resultant properties. To facilitate this, various percentages of boron nitride were incorporated into the PLA matrix, specifically at 5% and 10% by weight. The compounding process involved the blending of PLA and boron nitride followed by the creation of composite filaments measuring 1.75 mm in diameter and optimized for 3D printing. Subsequently, test specimens were meticulously fabricated in adherence with ASTM standards to evaluate the ultimate tensile strength, dimensional accuracy, wear characteristics, and surface roughness. The findings from these assessments were systematically compared to the wear properties and mechanical behavior of PLA composites reinforced with boron nitride and the unreinforced PLA material. This study serves as a foundational resource that offers insights into the feasibility and methodologies of incorporating boron nitride into PLA matrices, paving the way for enhanced polymer composite development.

The traditional way to machine hybrid composites is hard because they tend to break, have a high retraction, have a high service temperature, and have an uneven surface irregularity. For high-strength fiber/metal composite constructions, alternative machining methods have drawn interest as a solution to these problems. Current research focuses on enhancing the Abrasive Water Jet Machining process by optimizing its variables using a composite material of epoxy reinforced with silicon carbide, stainless steel wire mesh, and Kevlar. The variables assessed are the Nozzle-to-substrate gap (S), the Abrasive discharge molding and different percentages of silicon carbide (SiC) filler (0%, 3%, and 6% by weight), three different types of hybrid laminates (H1, H2, and H3) were produced. The response surface method (RSM) was utilized in this learning, specifically on a central composite design, to calculate and optimize machining variables based on the Kerf convergence ratio (K t ) and Surface irregularity (R a ) as responses. According to the results, the traverse feed velocity, Abrasive discharge proportion, and Nozzle-to-substrate gap are the critical factors in determining Surface irregularity and Kerf convergence width (H1 laminate) for a fiber/metal laminate with 0%, 3% and 6% weight fraction. In the case of a 3% weight fraction H2 laminate, the traverse feed velocity was identified as the primary factor affecting the Kerf convergence ratio. In contrast, traverse feed velocity and Nozzle-to-substrate gap had the most significant influence on Surface irregularity. The findings also indicated that S, followed by Abrasive discharge proportion and traverse feed velocity, are the variables that have the most significant influence when cutting 6 wt% SiC filler particle fiber/metal laminate (H3 laminate). For Surface irregularity, the combination of traverse feed velocity and Nozzle-to-substrate gap had the most significant impact. To validate the optimization results, confirmatory tests was conducted, and the findings were very similar to the experimental values, indicating the accuracy and effectiveness of the optimization process. To better understand the manufacturing processes, a scanning electron microscope was used to examine the morphological features of the machined surfaces, such as delamination, fibre breakage, and fibre pull-out., (© 2023. Springer Nature Limited.)

This paper offers a comprehensive analysis of algal-based membrane bioreactors (AMBRs) and their potential for removing hazardous and toxic contaminants from wastewater. Through an identification of contaminant types and sources, as well as an explanation of AMBR operating principles, this study sheds light on the promising capabilities of AMBRs in eliminating pollutants like nitrogen, phosphorus, and organic matter, while generating valuable biomass and energy. However, challenges and limitations, such as the need for process optimization and the risk of algal-bacterial imbalance, have been identified. To overcome these obstacles, strategies like mixed cultures and bioaugmentation techniques have been proposed. Furthermore, this study explores the wider applications of AMBRs beyond wastewater treatment, including the production of value-added products and the removal of emerging contaminants. The findings underscore the significance of factors such as appropriate algal-bacterial consortia selection, hydraulic and organic loading rate optimization, and environmental factor control for the success of AMBRs. A comprehensive understanding of these challenges and opportunities can pave the way for more efficient and effective wastewater treatment processes, which are crucial for safeguarding public health and the environment., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2023. Published by Elsevier Ltd.)

Biodiesel from Jatropha oil is produced through catalyzed homogeneous transesterification. Hydrogen peroxide (H 2 O 2 ) is considered as additive. Blends of Jatropha considered in the present study are 60% diesel, (40-A)% biodiesel and A% additive, varying A from 0 to 10. Identifying optimal input variables (such as additive volume percentage, injection pressure, and load) is important for improving the engine performance and reducing emissions. Air-fuel ratio; brake specific fuel consumption (BSFC); and brake thermal efficiency (BTE) are the engine performance characteristics. Carbon monoxide (CO); carbon dioxide (CO 2 ); exhaust gas temperature (EGT); nitrogen oxide (NO x ); and smoke opacity are the emission characteristics. 27 experiments need to be performed for the assigned 3 levels and 3 input variables. The Taguchi's L 9 orthogonal array (OA) is chosen to perform only 9 experiments to obtain the optimal solution. The expected range of performance characteristics and emissions was obtained following a modified Taguchi approach. Empirical relationships are developed and verified through engine performance and emission characteristics., Competing Interests: The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (© 2023 The Authors.)

Till now Mg-based alloys have attracted much attention due to the high storage capacity of hydrogen. An effort was made to evaluate the apparent activation energy and electrochemical behavior of transition metals such as scandium (Sc), zirconium (Zr), and niobium (Nb) alloyed with Mg-Ti. Mg 0.8 Ti 0.2 , Mg 0.6 Ti 0.2 Sc 0.2 , Mg 0.6 Ti 0.2 Zr 0.2 , and Mg 0.6 Ti 0.2 Nb 0.2 alloy powders were synthesized using high-energy ball milling. Ballmilled powders were subjected to structural and morphological characterization using X-ray diffraction and scanning electron microscopy respectively. A strong shift in the inter-planar spacing value of milled powders confirmed supersaturated solid solution of Ti and transition metals in Mg. The inter-planar spacing values before and after milling are found to be 0.24 and 0.21 nm, respectively. Mg 0.8 Ti 0.2 , Mg 0.6 Ti 0.2 Sc 0.2 , and Mg 0.6 Ti 0.2 Zr 0.2 alloy powders result in the FCC phase while Mg 0.6 Ti 0.2 Nb 0.2 powders result in BCC phase, however, the entire powders have an amorphous background. SEM-EDS analysis of the milled powders confirmed the presence of Mg, Ti, Sc, Zr, and Nb elements with a small amount of oxygen. Selected area electron diffraction (SAED) pattern of Mg 0.8 Ti 0.2 alloy powders exhibits a nanocrystalline nature owing to their polycrystalline ring pattern. Exothermic peak broadening increases after the substitution of Nb and Zr in Mg 0.8 Ti 0.2 alloy powder, which exhibits a lower activation energy (188 kJ mol -1 ) than others. In cyclic voltammetry, a drenched cathodic peak is observed for Mg 0.8 Ti 0.2 at a potential around -0.83 V. In electrochemical impedance spectroscopy, the charge transfer resistance of Mg 0.6 Ti 0.2 Sc 0.2 is lower than that of Mg 0.6 Ti 0.2 Zr 0.2 and Mg 0.6 Ti 0.2 Nb 0.2 alloy but higher than Mg 0.8 Ti 0.2 electrode materials, and charge-discharge studies were done on the developed electrode materials. It shows that Mg 0.8 Ti 0.2 electrode material delivers a maximum discharge capacity of 535 mA h g -1 ., Competing Interests: There is no conflict among authors., (This journal is © The Royal Society of Chemistry.)

Finding structurally similar compounds in compound databases is highly efficient and is widely used in present-day drug discovery methodology. The most-trusted and -followed similarity indexing method is Tanimoto similarity indexing. Epigenetic proteins like histone deacetylases (HDACs) inhibitors are traditionally used to target cancer, but have only been investigated very recently for their possible effectiveness against rheumatoid arthritis (RA). The synthetic drugs that have been identified and used for the inhibition of HDACs include SAHA, which is being used to inhibit the activity of HDACs of different classes. SAHA was chosen as a compound of high importance as it is reported to inhibit the activity of many HDAC types. Similarity searching using the UNPD database as a reference identified aglaithioduline from the Aglaia leptantha compound as having a ~70% similarity of molecular fingerprints with SAHA, based on the Tanimoto indexing method using ChemmineR. Aglaithioduline is abundantly present in the shell and fruits of A. leptantha . In silico studies with aglaithioduline were carried out against the HDAC8 protein target and showed a binding affinity of -8.5 kcal mol. The complex was further subjected to molecular dynamics simulation using Gromacs. The RMSD, RMSF, compactness and SASA plots of the target with aglaithioduline, in comparison with the co-crystallized ligand (SAHA) system, showed a very stable configuration. The results of the study are supportive of the usage of A. leptantha and A. edulis in Indian traditional medicine for the treatment of pain-related ailments similar to RA. Our study therefore calls for further investigation of A. leptantha and A. edulis for their potential use against RA by targeting epigenetic changes, using in vivo and in vitro studies.

Fused deposition modeling (FDM), one of the most widely used additive manufacturing (AM) processes, is used for fabrication of 3D models from computer-aided design data using various materials for a wide scope of applications. The principle of FDM or, in general, AM plays an important role in minimizing the ill effects of manufacturing on the environment. Among the various available reinforcements, short glass fiber (SGF), one of the strong reinforcement materials available, is used as a reinforcement in the acrylonitrile butadiene styrene (ABS) matrix. At the outset, very limited research has been carried out till date in the analysis of the impact and flexural strength of the SGF-reinforced ABS polymer composite developed by the FDM process. In this regard, the present research investigates the impact and flexural strength of SGF-ABS polymer composites by the addition of 15 and 30 wt % SGF to ABS. The tests were conducted as per ASTM standards. Increments in flexural and impact properties were observed with the addition of SGF to ABS. The increment of 42% in impact strength was noted for the addition of 15 wt % SGF and 54% increase with the addition of 30 wt % SGF. On similar lines, flexural properties also showed improved values of 44 and 59% for the addition of 15 and 30 wt % SGF to ABS. SGF addition greatly enhanced the properties of flexural and impact strength and has paved the path for the exploration of varied values of reinforcement into the matrix., Competing Interests: The authors declare no competing financial interest., (© 2023 The Authors. Published by American Chemical Society.)

The gel electrolyte significantly influences gel valve-regulated lead acid battery performance. To address this, the paper describes the preparation of novel polymer gel electrolytes using poly (vinyl alcohol) (PVA) and tetraethylorthosilicate (TEOS) for valve-regulated lead-acid batteries. FTIR technique is used to confirm the chemical reaction between PVA and TEOS. Electrochemical analyses such as cyclic voltammetry and electrochemical impedance spectroscopy were applied to optimize the concentration of PVA-TEOS polymer gel electrolyte. The optimum concentration of polymer gel electrolyte was determined as 20 wt% of TEOS in PVA (PE-1) with higher anodic peak and lower Rs and Rct values. The Galvanostatic charge-discharge tests were performed on the optimized gel system prototype battery. The highest capacity of 6.86 × 10 -5 Ah at a current density of 0.2 mA cm -2 was achieved with an excellent capacity retention ratio of 85.7% over 500 cycles. The exceptional cycle performance and high capacity make PVA-TEOS gel electrolyte a promising candidate for practical battery application.

Nanobacterial cellulose (NBC) was produced and incorporated into biodegradable poly(vinyl alcohol) (PVA) in different weight ratios to obtain polymer nanocomposite membranes. The physicochemical properties of the membranes were studied using Fourier transform infrared (FTIR) spectroscopy, a universal testing machine (UTM), thermogravimetric analysis (TGA), wide-angle X-ray diffraction (WAXD) techniques, and field emission scanning electron microscopy (FESEM). FTIR confirmed the consolidation of NBC into PVA by exhibiting significant changes in the peaks compared to NBC and PVA individually. The highest tensile strength of 53.33 MPa and 235.30% elongation at break of the membrane M-10 mass % NBC was obtained, illuminating that NBC provides stiffness and PVA imparts elasticity. WAXD revealed that the crystalline nature of the membrane increases up to 10 mass % and decreases beyond it. The effect of NBC on the poly(vinyl alcohol) membranes for food packaging was investigated systematically. Among all the membranes, M-10 mass % NBC was found to be the most suitable for packaging applications. Membranes had antimicrobial activity against food microbes and showed degradability behavior in the soil. The tests on membranes for packaging revealed that fruits were protected from spoilage caused by microorganisms. Hence, the prepared membranes could be used as an alternative to conventional plastics for packaging applications., Competing Interests: The authors declare no competing financial interest., (© 2022 The Authors. Published by American Chemical Society.)

Polymer-based nanocomposites are being considered as replacements for conventional materials in medium to high-temperature applications. This article aims to discover the synergistic effects of reinforcements on the developed polymer-based nanocomposite. An epoxy-based polymer composite was manufactured by reinforcing graphene nanoplatelets (GNP) and h-boron nitride (h-BN) nanofillers. The composites were prepared by varying the reinforcements with the step of 0.1 from 0.1 to 0.6%. Ultrasonication was carried out to ensure the homogenous dispersion of reinforcements. Mechanical, thermal, functional, and scanning electron microscopy (SEM) analysis was carried out on the novel manufactured composites. The evaluation revealed that the polymer composite with GNP 0.2 by wt % has shown an increase in load-bearing capacity by 265% and flexural strength by 165% compared with the pristine form, and the polymer composite with GNP and h-BN 0.6 by wt % showed an increase in load-bearing capacity by 219% and flexural strength by 114% when compared with the pristine form. Furthermore, the evaluation showed that the novel prepared nanocomposite reinforced with GNP and h-BN withstands a higher temperature, around 340 °C, which is validated by thermogravimetric analysis (TGA) trials. The numerical simulation model is implemented to gather the synthesised nanocomposite's best composition and mechanical properties. The minor error between the simulation and experimental data endorses the model's validity. To demonstrate the industrial applicability of the presented material, a case study is proposed to predict the temperature range for compressor blades of gas turbine engines containing nanocomposite material as the substrate and graphene/h-BN as reinforcement particles.

Geopolymer is the alternative to current construction material trends. In this paper, an attempt is made to produce a sustainable construction composite material using geopolymer. Ground granulated blast furnace slag (GGBS)-based geopolymer concrete was prepared and tested for different alkaline to binder ratios (A/B). The effect of various temperatures on compressive strength properties was assessed. The cubes were exposed to temperature ranging from 50 to 70 °C for a duration ranging from 2 to 10 h, and the compressive strength of the specimens was analyzed for destructive and non-destructive analysis and tested for 7, 28, and 90 days. The obtained compressive strength (CS) results were analyzed employing the probability plot (PP) curve, distribution overview curve (DOC), probability density function (PDF), Weibull, survival, and hazard function curve. Maximum compressive strength was achieved for the temperature of 70 °C and an A/B of 0.45 for destructive tests and non-destructive tests with 44.6 MPa and 43.56 MPa, respectively, on 90 days of testing. The survival and hazard function curves showed incremental distribution characteristics for 28 and 90 days of testing results with a probability factor ranging from 0.8 to 1.0.

Biosurfactants are eco-friendly surface-active molecules recommended for enhanced oil recovery techniques. In the present study, a potential lipopeptide (biosurfactant) encoding the iturin A gene was synthesized from Bacillus aryabhattai . To improvise the yield of the lipopeptide for specific applications, current research tends toward engineering and expressing recombinant peptides. An iturin A gene sequence was codon-optimized, amplified with gene-specific primers, and ligated into the pET-32A expression vector to achieve high-level protein expression. The plasmid construct was transformed into an E. coli BL21 DE3 host to evaluate the expression. The highly expressed recombinant iturin A lipopeptide was purified on a nickel nitrilotriacetic acid (Ni-NTA) agarose column. Sodium dodecyl sulfate polyacrylamide gel electrophoresis (SDS-PAGE) revealed that the purity and molecular mass of iturin A was 41 kDa. The yield of recombinant iturin A was found to be 60 g/L with a 6.7-fold increase in comparison with our previously published study on the wild strain. The approach of cloning a functional fragment of partial iturin A resulted in the increased production of the lipopeptide. When motor oil was used, recombinant protein iturin A revealed a biosurfactant property with a 74 ± 1.9% emulsification index (E24). Purified recombinant protein iturin A was characterized by mass spectrometry. MALDI-TOF spectra of trypsin digestion (protein/trypsin of 50:1 and 25:1) showed desired digested mass peaks for the protein, further confirming the identity of iturin A. The iturin A structure was elucidated based on distinctive spectral bands in Raman spectra, which revealed the presence of a peptide backbone and lipid. Recombinant iturin A was employed for enhanced oil recovery through a sand-packed column that yielded 61.18 ± 0.85% additional oil. Hence, the novel approach of the high-level expression of iturin A (lipopeptide) as a promising biosurfactant employed for oil recovery from Bacillus aryabhattai is not much reported. Thus, recombinant iturin A demonstrated its promising ability for efficient oil recovery, finding specific applications in petroleum industries.

This study investigates the effects of red mud on the performance of geopolymer concrete in regard to fresh and mechanical properties. Red mud was used as a binder, and GGBS replaced the binder. Different proportions of red mud ranging from 0 to 30% with an interval of 2% and activator agents such as KOH and K 2 SiO 3 for various alkaline-to-binder ratios such as 0.30, 0.40, and 0.50 were used; their effect on the fresh and mechanical properties of geopolymer concrete were the focusing parameter on the current study. Fresh properties such as setting time, slump, compaction factor, and vee-bee consistometer test, and mechanical properties such as compressive strength, split tensile strength, flexural strength, modulus of elasticity, and impact energy were studied. ANOVA and radar plot analysis were studied for various alkaline to binder (A/B) compressive strength results tested for 7 to 90 days. The increase of red mud quantity caused the decline of workability, but there was continuous enhancement of mechanical properties of GPC up to a specific limit. An alkaline-to-binder ratio of 0.4 shows excellent results compared with other ratios at ambient conditions for strength properties. ANOVA and radar plot reveal that A/B of 0.40 for 90 days shows excellent results compared with other ratios, and CS values vary in a linear manner.

Abstract: The global market for fuel pellets (FPs) has been steadily growing because of a shift to coal substitutes. However, sustainability and the availability of biomass are the main issues. Various kinds of bio-wastes can be valorized through cutting-edge technologies. In the coffee industry, a valuable organic waste called spent coffee grounds (SCGs) is generated in bulk. SCG can be divided into two components, namely spent coffee ground oil and defatted spent coffee grounds (DSCG). SCG and DSCG can be used to produce FPs with excellent higher heating values. This review highlights that burning FPs composed of 100% SCG is not feasible due to the high emission of NO x . Moreover, the combustion is accompanied by a rapid temperature drop due to incomplete combustion which leads to lower boiler combustion efficiencies and increased carbon monoxide emissions. This was because of the low pellet strength and bulk density of the FP. Mixing SCG with other biomass offers improved boiler efficiency and emissions. Some of the reported optimized FPs include 75% SCG + 20% coffee silverskin, 30% SCG + 70% pine sawdust, 90% SCG + 10% crude glycerol, 32% SCG + 23% coal fines + 11% sawdust + 18% mielie husks + 10% waste paper + 6% paper pulp, and 50% SCG + 50% pine sawdust. This review noted the absence of combustion and emissions analyses of DSCG and the need for their future assessment. Valorization of DSCG offers a good pathway to improve the economics of an SCG-based biorefinery where the extracted SCGO can be valorized in other applications. The combustion and emissions of DSCG were not previously reported in detail. Therefore, future investigation of DSCG in boilers is essential to assess the potential of this industry and improve its economics., Supplementary Information: The online version contains supplementary material available at 10.1007/s10668-022-02361-z., (© The Author(s), under exclusive licence to Springer Nature B.V. 2022.)

The main objective of this review is to study some important nanomaterials and their impact on the performance of geopolymer concrete. This paper is an investigation into trends and technology in the development of different nanomaterials to develop higher structural performance geopolymer concrete. The effect of the alkaline to binder and sodium silicate to sodium hydroxide ratio on the performances of geopolymer performances is studied. The relationship between setting time and slump is evaluated through the ternary plot, the variation in compressive strength values is evaluated using the kernel density plot, and the relationship between split tensile and flexural strength is investigated using the scattering interval plot. Regression analysis is carried out among water absorption and bulk-density result values obtained from previous literature. As the molarity and alkaline to binder (A/B) ratios increase, the strength development of geopolymer concrete increases up to a specific limit. The addition of a small quantity of nanomaterials, namely, nano silica, nano alumina, carbon nano tubes, and nano clay, led to the maximum strength development of geopolymer concrete. Incorporating these nanomaterials into the geopolymer significantly refines the structural stability, improving its durability. The various products in GP composites emerging from the incorporation of highly reactive SEM, XRD, and FTIR analysis of nanomaterials reveal that the presence of nanomaterials, which enhances the rate of polymerization, leads to better performance of the geopolymer.

One of the most promising and widely used additive manufacturing technologies, fused deposition modelling (FDM), is based on material extrusion and is most commonly used for producing thermoplastic parts for functional applications with the objectives of low cost, minimal waste and ease of material conversion. Considering that pure thermoplastic materials have a significantly poor mechanical performance, it is necessary to enhance the mechanical properties of thermoplastic parts generated using FDM technology. One of the conceivable techniques is to incorporate reinforcing materials such as short glass fibre (SGF) into the thermoplastic matrix in order to produce a polymer composite that can be used in engineering applications, such as structural applications. The morphological and mechanical properties of SGF (short glass fibre) reinforced ABS- (Acrylonitrile Butadiene Styrene) based polymer composites created via the method of FDM (fused deposition modelling) were investigated in this work. Properties were evaluated at three different weight percentages (0, 15 and 30 wt%). The composite filaments were developed using the process of twin screw extrusion. The comparison was made between ABS + SGF (short glass fibre) composites and pure ABS of mechanical properties that include surface roughness, tensile strength and low-velocity impact. The tests were carried out to analyze the properties as per ASTM standards. It has been found that the impact strength and tensile strength show an improvement in glass fibre inclusion; moreover, alongside the direction of build, the surface roughness had been reduced. The studies also focused on studying the dispersion characters of SGF in ABS matrix and its impact on the properties. Strength and modulus of SGF reinforced ABS composite has been significantly improved along with reduction of ductility. A 57% increase in tensile strength has been noted for 30 wt% addition of SGF to ABS in comparison to pure ABS. It was also interesting to note the reduction in surface roughness with every incremental addition of SGF to ABS. A 40% reduction in surface roughness has been observed with a 30 wt% addition of SGF to ABS in comparison to pure ABS.

AA2050-T84 alloy is widely used in primary structures of modern transport aircraft. AA2050-T84 is established as a low-density aluminum alloy with improved Young's modulus, less anisotropy, and temperature-dependent mechanical properties. During flights, loading rate and temperature variation in aircraft engine subsequent parts are commonly observed. The present work focuses on the effect of loading rate and temperature on tensile and fracture properties of the 50 mm thick (2-inch) AA2050-T84 alloy plate. Quasi-static strain rates of 0.01, 0.1, and 1 s -1 at -20 °C, 24 °C and 200 °C are considered. Tensile test results revealed the sensitivity of mechanical properties towards strain rate variations for considered temperatures. The key tensile properties, yield, and ultimate tensile stresses were positive strain rate dependent. However, Young's modulus and elongation showed negative strain rate dependency. Experimental fracture toughness tests exhibited the lower Plane Strain Fracture Toughness ( K IC ) at -20 °C compared to 24 °C. Elastic numerical fracture analysis revealed that the crack driving and constraint parameters are positive strain rate dependent and maximum at -20 °C, if plotted and analyzed over the stress ratio. The current results concerning strain rates and temperatures will help in understanding the performance-related issues of AA2050-T84 alloy reported in aircraft applications.