Search

We propose methods to obtain multi-domains with different threshold voltages for vertically aligned liquid crystal displays without additional transistors or capacitors. We exposed an ultraviolet light through a photomask and spatially varied the surface anchoring energy by partially decomposing the polyimide or inducing the adsorption of reactive monomers. The threshold voltage was reduced with smaller surface anchoring, and the reduction of the threshold could be qualitatively interpreted using a model describing a weak anchoring condition. [ABSTRACT FROM AUTHOR]

A light scatter-free, transparent, thermally stable, optically isotropic liquid crystal mixture was achieved among three different mixtures of liquid crystal E7: Norland Optical Adhesive 65 with concentrations 30:70, 40:60, and 50:50 wt%. The 50:50 wt% mixture exhibited the best performed optically isotropic state when exposed to ultraviolet light of intensity 150 mW/cm 2 for droplet formation. The high intensity ultraviolet light curing process induces nano-sized liquid crystal droplets in the polymer matrix of average droplet size 218 nm, characterized by scanning electron microscope. The analyzed result shows an excellent contrast ratio (CR) equal to 1574 at the normal direction and a high CR at a wide viewing angle. The magnitude of Kerr constant in these nano-sized PDLC was ~7.36×10 −10 mV −2 , which was more than ~330 times that of a conventional Kerr material such as nitrobenzene. Unprecedented fast rising and falling times of approximately 385 µs and 1.1 ms, respectively, were achieved for the device. This high-performance material also eliminated the long-term hurdle of hysteresis to make it a promising candidate for next-generation display and photonic technologies. [ABSTRACT FROM AUTHOR]

We propose a method for vertical alignment (VA) of liquid crystals (LCs) without alignment layers by mixing only a very low concentration (0.05 wt%) of an organic compound with LCs. The electro-optic characteristics of a VA cell fabricated by the proposed method were almost the same as those of a conventional VA cell with VA layers. Moreover, we used the proposed method to realise a polymer-stabilised VA device with a rapid response time without alignment layers. The proposed method can simplify the fabrication process and reduce the manufacturing cost of LC display devices by removing the need for alignment layers and the alignment process such as coating of polyimide layers and the UV exposure for the photo-alignment. We believe that the proposed method can play an essential role in the fabrication of plastic flexible LC display devices requiring the low-temperature process. [ABSTRACT FROM AUTHOR]

A transflective liquid crystal display using polymer-stabilised vertical alignment mode with fishbone-shaped electrode structure is proposed. Using the polymer stabilisation technique and patterned direction of pixel electrode structure, initial surface tilt angle and azimuthal angle can be well defined such that the liquid crystal is almost vertically aligned in the transmissive part while it has a certain pretilt angle that satisfies effective retardation of λ/4 with azimuthal direction of 45o with respect to the analyser in the reflective part. With optimisation of cell structures and surface tilt angles in the transmissive and reflective parts, a high performance transflective display showing excellent readability in any environment light conditions and single-gamma characteristic without using any retardation film or in-cell retarder can be achieved. [ABSTRACT FROM AUTHOR]

- Three different blue-phase I liquid-crystal samples with different grain-size distribution were studied. Polycrystalline platelet grains reflects light in the visible region and have been observed under a polarizing optical microscope. Green and blue grain areas have been measured and then the statistical histogram by the Gaussian distribution function was fitted and the mean grain size was calculated. The effect of hysteresis on grain size has been compared for the three samples. Hysteresis depends explicitly on the grain-size distribution. Large grain size has revealed less hysteresis, while small grain size depicted pronounced hysteresis. [ABSTRACT FROM AUTHOR]

For the fabrication of protrusions in multi-domain vertical alignment liquid crystal displays (MVA-LCDs), a series of complicated and expensive photolithographic processes has to be gone through for the wide viewing angles. In this research, we proposed and demonstrated a new manufacturing approach of the protrusion utilising ink-jet printing technology. Parallel lines were ink-jet printed on the substrates and solidified by a subsequent baking process, and then used as the protrusions of MVA-LCDs. The geometric dimensions of the protrusion patterns were optimised by the comparison of experimental observations and computer simulation results. The MVA-LCD cell was fabricated by arranging the protrusion lines forming right angles between the top and the bottom lines, which resulted in cross-line protrusions. Due to the square-shaped geometric arrangement of the protrusions, the vertically aligned LCs formed the symmetric four-domains in the MVA-LCD cell. With the help of a surface polymer-stabilisation technique, the response time of the LC molecules under the electric field was significantly improved. Therefore, we can conclude that, without sacrificing the viewing angle and response time of MVA-LCD, the printing technique for the formation of the protrusions can give us a new fabrication opportunity with low cost in contrast to the conventional photolithography process. [ABSTRACT FROM PUBLISHER]

We propose a pixel electrode structure for the multi-domain vertical alignment liquid crystal mode with high optical efficiency. We form a micro-slit electrode structure on the top substrate to reduce the width of disclination lines at domain boundaries. We insert additional electrodes on the bottom substrate to improve the transmittance at the edges of each pixel. We confirm that using both structures, the transmittance can be increased from 22.9% to 27.3% with no change in the operating voltage. [ABSTRACT FROM AUTHOR]