Search

Diagnosis on electrostatic charging tendency (ECT) of mineral insulating oil for power transformers has been performed. Increase in the ECT is derived from sulfonium ions, which are generated by sulfoxide compounds and hydrogen ions. Strong correlation between the ECT and the sulfoxide concentration is obtained in a series of thermal aging tests with oxygen and/or copper catalyst. The volume resistivity of oil is used as an alternative indicator for the concentration of hydrogen ion because hydrogen ions increase the electrical conductivity of oil and the sensitivity of conventional property such as total acid value is too low to evaluate the aging deterioration of closed-type transformers. Analysis of oils extracted from 98 actual transformers, whose operating years are between 3 and 46 years, are performed. High ECT values more than 200 pC/ml are detected in some oils and their volume resistivity values are less than 4 x 1014 Ωcm. Degree of the correlation between the ECT and the sulfoxide concentration is low compared to the result of the thermal aging tests. A diagnostic map with four areas classified using a pair of indicators of volume resistivity and sulfoxide concentration is useful to predict prospective increases in the ECT. Appropriate transformer operation and maintenance including air exposure avoidance of their mineral insulating oils is one of the effective solutions to prevent the ECT from increasing. [ABSTRACT FROM AUTHOR]

To ensure soundness of highly aged transformers in their operations, it is important to identify how aging influences insulating oil in these transformers. The characteristics of insulating oil are roughly classified into electrical, physical, and chemical characteristics. In the past research on insulating oil in transformers, some of the characteristics showed a downward trend with increasing age. Among the electrical characteristics, the volume resistivity and the dielectric loss tangent showed a downward trend with increasing age, which is likely to reflect degradation that accompanies aging. The analysis of insulating oil components found some components that increased with age, which may contribute to degrading electrical characteristics of insulating oil. This study on field transformers gave results obtained through comparison of different samples in relation to the number of years in which they were in the field. Detailed evaluation of aging requires study on aging patterns using the same samples. In this paper, heat-accelerated degradation test was conducted on the same samples, and the patterns of changes in characteristics were studied. In addition, the influences of interactions between characteristics and water and between characteristics and pressboard were examined. The study using accelerated degradation test was conducted on one brand of mineral oil (α1). The obtained characteristics were the breakdown voltage, volume resistivity, interfacial tension, total acid value, and water content, i.e., electrical characteristics and characteristics considered to be correlated with electrical characteristics were extracted. As a result of examination, characteristic deterioration was evident for the water content, breakdown voltage, volume resistivity, total acid value, and interfacial tension in descending order of deterioration. The characteristics showed evident deterioration in the initial stage of accelerated degradation test and, thereafter, showed a saturation tendency with increasing age. [ABSTRACT FROM AUTHOR]

Additives to insulating oil and oil treatment by absorbents are investigated by thermal aging tests with the aim of suppressing flow electrification in power transformer insulation. 1, 2, 3-benzotriazol (BTA) is found to be effective for suppressing the increase of electrostatic charging tendency (ECT) in oils that contain either sulfide or sulfoxide compounds. Sulfide compounds are contained in new oil while sulfoxide compounds are generated by the oxidation of sulfide compounds. However, 2, 6-ditertiary-butyl paracresol (DBPC) is only effective for oils that contain sulfide compounds. The addition of sulfoxide compounds significantly increases the ECT of DBPC-added oil by the thermal aging tests. DBPC can suppress the conversion of sulfide to sulfoxide by blocking the generation of peroxide. However, DBPC has negligible effect on suppressing the increase in ECT by sulfonium ions, which are generated by the oxidation of sulfoxide. Negatively charged BTA ions, which are generated by the dissociation of hydrogen ions from BTA molecules, can mitigate the increase in ECT by sulfonium ions, which charge insulating oil positively. The effect of BTA is found to be lost when the concentration in oil decreases due to the adsorption on solid insulators. Oil treatment by absorbents such as clay, activated carbon and silica gel is found to remarkably decrease the ECT of deteriorated oil. However, additional thermal aging test increases the ECT to the same level as before the oil treatment. Although the additives and the oil treatment by absorbents are effective for suppressing and decreasing the ECT of insulating oils, their long-term effect is not assured. Thus periodical measurements of the ECT of insulating oils are crucial for the sake of preventive maintenance of aged transformers. [ABSTRACT FROM AUTHOR]

Electrostatic charging mechanism in aged oil-immersed transformers is investigated. Sulfonium ions, which are generated by sulfoxide compounds and hydrogen ions, are identified as the prime compounds that increase electrostatic charging tendency (ECT) of mineral insulating oil. Sulfoxide compounds are generated by the oxidation of sulfide compounds that are contained in new oil. Hydrogen ions are considered to be supplied by organic acids that are generated due to the oxidation of hydrocarbons. Negative ions with low mass are generated by the dissociation of organic acids during the generation of sulfonium ions. Because these negative ions are hydrophilic, the oil is charged positively. Water is also generated by the deterioration of insulating oils and has the same effect. On the other hand, negative charging of oil is detected with the addition of sulfonic acids, which reflects the generation of positive ions with low mass and hydrophility. [ABSTRACT FROM AUTHOR]

To ensure long-term reliability of transformers, it is important to identify the degradation characteristics of insulating oil in long-term operations, which are the dominant factors of the transformer dielectric strengths. Analysis on aged field insulating oil was conducted to identify how insulating oil in transformers changes and deteriorates with increasing age and what are the impacts on the electrical characteristics such as breakdown voltages. Insulating oil samples were collected from a total of 98 transformers, varying significantly with six manufacturers, manufacture years of 1956 to 1999, and voltage classes of 66 kV to 500 kV. Electrical, physical and chemical characteristics were obtained, and the impact of increasing age and the relationships among characteristics were evaluated. The characteristics found to deteriorate with increasing age were volume resistivities, dielectric loss tangents, interfacial tensions, and total acid values. These characteristics can be used as effective indexes for trend monitoring to identify aging statuses and detect abnormalities at an early stage. The physical characteristics (kinetic viscosities, densities, and flash points) showed different tendencies depending on the oil type and age. Since the physical characteristics depend on the compositions of insulating oil, the possible causes for this result are that the compositions of insulating oil were different between oil types and that the compositions varied in accordance with increasing age. Furthermore, the correlations between characteristics were evaluated. As a result, a correlation was found between volume resistivities and total acid values, and good correlations were found between interfacial tensions and volume resistivities and total acid values. interfacial tensions, which change with a higher rate than total acid values, can be possibly used as an effective index for insulating oil degradation. [ABSTRACT FROM AUTHOR]

Analysis methods of sulfide and sulfoxide compounds in mineral insulating oil are developed to diagnose an electrostatic charging of a power transformer due to oil circulation. When sulfonium ions are generated from sulfide compounds via sulfoxide compounds, they tend to increase an electrostatic charging tendency (ECT) in the oil, which causes the electrostatic charging of a power transformer. Selective analysis methods for sulfide and sulfoxide compounds are developed by combining solid extractions with a gas chromatography because it is difficult to detect sulfonium ions directly. Sulfide compounds are selectively extracted from oils by palladium chlorideimpregnated silica gel while sulfoxide compounds are extracted by silica gels. The effect of sulfide on the dielectric dissipation factor (DDF), which relates to an ECT, of commercial oil is investigated by removing sulfide compounds with palladium chlorideimpregnated silica gel. The DDF of untreated oil increases at the beginning of heating with air while changes in the DDF are minimal for treated oils. [ABSTRACT FROM PUBLISHER]

To identify the aging characteristics of oil-immersed transformer oil in long-term operations, it is important to survey various characteristics of insulating oil of field transformers. The insulating oil characteristics defined in various standards can be roughly classified into electrical, physical, and chemical characteristics. In a past study, the authors identified through field survey what kind of characteristics receive significant impacts as a result of insulating oil aging and evaluated the characteristics as possible candidates for indexes of aging. This paper examines the elements that influence the characteristics of transformer insulating oil due to aging. The electrical characteristics (breakdown voltages, volume resistivities, and dielectric loss tangents) of insulating oil are affected by such elements as water contents and electrostatic charges and possibly by trace components in the insulating oil. The components detected in field transformer oil are methyl acetate, 2-methylfuran, phenol, methyl formate, furan, methanol, ethanol, acetone, isopropyl alcohol, and methyl ethyl ketone. Five of these components, i.e., methanol, ethanol, acetone, isopropyl alcohol, and methyl ethyl ketone, are alcohols and ketones. These five components are generated by age-related oxidation. The five components, except for methanol, was found to have age-related increasing tendencies. Methyl acetate, 2-methylfuran, phenol, methyl formate, and furan are considered to be components mainly generated by the reason of insulating paper aging. Whereas 2-methylfuran and furan were found to have agerelated increasing tendencies, other components were found to have none. Analysis of insulating oil components is effective in diagnosing the aging status of insulating oil and the presence or absence of abnormalities. This paper summarizes the result of survey on the relationships between the concentrations of components and the ages of insulating oil based on the analysis results of the oil components. [ABSTRACT FROM AUTHOR]

Partial discharge (PD) resistance was examined by applying a constant voltage to four different biodegradable polymers—poly-L-lactic acid (PLLA), polyethylene terephthalate succinate (PETS), poly ℇ-caprolactone butylene succinate (PCL-BS), and polybutylene succinate (PBS)—and the results were compared with those of low-density polyethylene (LDPE) and crosslinked low-density polyethylene (XLPE). The PD resistance is determined by the erosion depth and the surface roughness caused by PDs, and is ranked as LDPE≈XLPE>PLLA≈PETS>PBS>PCL-BS. This means that the sample with a lower permittivity has better PD resistance. Furthermore, examination of the sample surfaces by a polarization microscope and a laser confocal microscope reveals that the PD resistance of crystalline regions with spherulites is higher than that of amorphous regions. Therefore, good PD resistance can be achieved by the sample with a high crystallinity and a low permittivity. © 2009 Wiley Periodicals, Inc. Electr Eng Jpn, 168(2): 1–10, 2009; Published online in Wiley InterScience (www.interscience.wiley.com). DOI 10.1002/eej.20807 [ABSTRACT FROM AUTHOR]

This paper describes the surface breakdown characteristics of silicone oil which has the possibility of application to innovative switchgears and transformers as an insulating medium. At the first step, we have experimentally studied the impulse breakdown characteristics of the configuration with a triple-junction where a solid insulator is in contact with the electrode. The test configuration consists of solid material (Nomex⊗ or pressboard) and liquid insulation oil (silicone or mineral oil). We have discussed the experimental results based on the maximal electric field at the triple-junction. As the second step, we have studied the configuration which may improve the surface breakdown characteristics by lowering the electric field on the insulator surface. [ABSTRACT FROM AUTHOR]