Search

Integrating wave energy devices with breakwaters can offer an innovative and sustainable approach by combining wave power extraction with wave attenuation. The performance of this integrated system in offshore areas is influenced by the unique characteristics of the coastline. In this paper, a semi-analytical solution was developed using the matching eigenfunction method for the oscillating water column device integrated into a pile-supported breakwater in front of a partially reflective seawall. The model was validated through the energy conservation law, the Haskind relationship, and experimental data. Detailed examinations were conducted on the effects of the seawall's reflection coefficients, the distance between the system and the seawall, the wall draft, and the chamber breadth on hydrodynamic performance. Results show that the presence of the seawall significantly influences hydrodynamic coefficients (hydrodynamic efficiency, reflection coefficient, the relative transmitted amplitude, etc.), accompanied by the piston and sloshing mode resonances inside the chamber and the confined area between the system and the seawall. Due to energy dissipated by a partially reflective seawall, the magnitude of those hydrodynamic coefficients is mitigated, together with the piston and sloshing mode resonances inside the air chamber. The cancellation of the sloshing mode resonance inside the confined area is observed for the smaller seawall's reflection coefficient. The maximum and minimum hydrodynamic efficiency occur when the system is arranged at the wave nodes and antinodes of the formed standing wave field. Lower wave reflection and better wave power extraction can be achieved by properly adjusting the chamber drafts and breadths. [ABSTRACT FROM AUTHOR]

Alumina (Al2O3) ceramics are widely used in electronics, machinery, healthcare, and other fields due to their excellent hardness and high temperature stability. However, their high brittleness limits further applications, such as artificial ceramic implants and highly flexible protective gear. To address the limitations of single-phase toughening in Al2O3 ceramics, some researchers have introduced a second phase to enhance these ceramics. However, introducing a single phase still limits the range of performance improvement. Therefore, this study explores the printing of Al2O3 ceramics by adding two different phases. Additionally, a new gradient printing technique is proposed to overcome the limitations of single material homogeneity, such as uniform performance and the presence of large residual stresses. Unlike traditional vat photopolymerization printing technology, this study stands out by generating green bodies with varying second-phase particle ratios across different layers. This study investigated the effects of different contents of sepiolite fiber (SF) and 316L stainless steel (SS) on various aspects of microstructure, phase composition, physical properties, and mechanical properties of gradient-printed Al2O3. The experimental results demonstrate that compared to Al2O3 parts without added SF and 316L SS, the inclusion of these materials can significantly reduce porosity and water absorption, resulting in a denser structure. In addition, the substantial improvements, with an increase of 394.4% in flexural strength and an increase of 316.7% in toughness, of the Al2O3 components enhanced by incorporating SF and 316L SS have been obtained. [ABSTRACT FROM AUTHOR]

Vat photopolymerization is an effective and economical method for preparing ceramic specimens with complex structures. However, the improper selection of process parameters during the preparation process limits the scope of its application. In this study, the most suitable shear rate was determined based on the solid content and rheological properties of the ceramic slurry. In addition, the specific printing‐process parameters were objectively selected, and the gray correlation method was used to determine the improved weight resolution coefficient through orthogonal experiments combined with the entropy weight method to select the most suitable printing parameters. Finally, the main debinding and sintering parameters that affect the heat treatment performance were considered, and multiple characterization methods were used to detect the specimens and study the impact of parameter changes on specimen performance. The experimental results show that when the laser power is 210 mW, the slice layer thickness is.04 mm, the scanning spacing is.05 mm, and the filling mode is XY, the green bodies have the best forming quality. When the sintering temperature is 1600°C, and the holding time is 4 h, the specimens have the best mechanical properties (the flexural strength reaches 114 MPa). [ABSTRACT FROM AUTHOR]

Vat photopolymerization (VPP), as an additive manufacturing (AM) technology, can conveniently produce ceramic parts with high resolution and excellent surface quality. However, due to the inherent brittleness and low toughness of ceramic materials, manufacturing defect-free ceramic parts remains a challenge. Many researchers have attempted to use carbon fibers as additives to enhance the performance of ceramic parts, but these methods are mostly applied in processes like fused deposition modeling and hot pressing. To date, no one has applied them to VPP-based AM technology. This is mainly because the black carbon fibers reduce laser penetration, making it difficult to cure the ceramic slurry and thus challenging to produce qualified ceramic parts. To address this issue, our study has strictly controlled the amount of carbon fibers by incorporating trace amounts of carbon fiber powder into the original ceramic slurry with the aim to investigate the impact of these additions on the performance of ceramic parts. In this study, ceramic slurries with three different carbon fiber contents (0 wt.%, 0.1 wt.%, 0.2 wt.%, and 0.3 wt.%) were used for additive manufacturing. A detailed comparative analysis of the microstructure, physical properties, and mechanical performance of the parts was conducted. The experimental results indicate that the 3D-printed alumina parts with added carbon fibers show varying degrees of improvement in multiple performance parameters. Notably, the samples prepared with 0.2 wt.% carbon fiber content exhibited the most significant performance enhancements.