Search

In the present work, the operating results from an innovative, renewable, energy-based space-heating and domestic hot water (DHW) system are shown. The system used solar thermal energy as its primary source and was assisted by a shallow geothermal application in order to accommodate the space-heating and DHW needs of a domestic building in Austria. The system incorporated phase-change materials (PCMs) in specially designed containers to function as heat-storage modules and provide an energy storage capability for both the space-heating and DHW subsystems. This system was designed, implemented, and tested under real operating conditions in a building for a period of one year. The operating and energy results for the system are demonstrated in this work. The system was compared with a conventional one, and a reduction in the primary energy consumption equal to 84.3% was achieved. The maintenance and operating costs of the system were reduced by 79.7% compared to the conventional system, thus significantly contributing to the NZEB target of the building. The newly proposed system, although presenting an increased operating complexity, utilizes an innovative self-learning control system that manages all of its operations. The combination of a solar thermal energy source with thermal energy storage increases the use of renewable energy by extending the capacity of the system beyond the solar hours and using excess solar energy for space-heating needs. The thermal energy storage unit also increases the energy and economic efficiency of the geothermal heat pump by operating it during the hours of a reduced electricity tariff and using the stored energy during hours of a high electricity demand. The cost for the installation of such a system is higher than a conventional one, but due to the significantly decreased operating costs, the pay-back period was calculated to be 8.7 years. [ABSTRACT FROM AUTHOR]

The increasing demand for food, the lack of natural resources and arable land, and the recent restrictions on energy consumption require an immediate solution in terms of agricultural activities. This paper's objective was to review hydroponics (a new soilless cultivation technology) and compare it with conventional agriculture (soil cultivation) regarding its environmental impact and water and energy consumption. The soil loss, the crop/soil contamination, and the greenhouse gas emissions were the criteria for the environmental comparison of conventional agriculture and hydroponics. As for resource consumption, the water consumption rates (L/kg), energy consumption rates (kWh), and energy required (kW) were the criteria for comparing conventional agriculture with hydroponics. Tomato and cannabis cultivation were used as case studies in this review. The review results showed that the advantages of hydroponics over conventional cultivation include zero-soil cultivation, land-use efficiency, planting environment cleanliness, fertilizer and resource saving, water consumption reduction, and conservation. The disadvantages of hydroponics versus conventional cultivation were found to include the high investment costs, technical know-how requirements, and higher amount of demanded energy. [ABSTRACT FROM AUTHOR]

This paper presents results of the experimental study for a 10-kWe Organic Rankine Cycle (ORC) unit that has been designed and developed in order to study its performance when solar or geothermal sources are used. A boiler was used to simulate those conditions and adjustments were made to generate the final heat by a solar or geothermal source in the same pace, size and way, which accurately reflects the operation of each system. R134a was selected as the working fluid. Measurements for key parameters at various points of the cycle were conducted and performance assessment was attempted. Based on the system operation under the conditions that were applied, and considering the various seasons of the year, it was found that the ORC unit working with low-temperature sources is likely to act as a complementary recovery system of heat quantities as the efficiency is rather small, but able to support other systems. [ABSTRACT FROM AUTHOR]

A numerical study was carried out to investigate charging and discharging processes of different phase change materials (PCMs) used for thermal storage in an innovative solar collector, targeting domestic hot water (DHW) requirements. The aim was to study PCMs that meet all application requirements, considering their thermal performance in terms of stored and retrieved energy, outlet temperatures, and water flow rate. Work was carried out for three flat-plate solar panels of different sizes. For each panel, a PCM tank with a heat exchanger was attached on the back plate. Simulations were conducted on a 2D domain using the enthalpy–porosity technique. Three paraffin-based PCMs were studied, two (A53, P53) with phase-change temperatures of approximately 53 °C and one of approximately 58 °C (A58H). Results showed that, during charging, A58H can store the most energy and A53 the least (12.30 kWh and 10.54 kWh, respectively, for the biggest unit). However, the biggest unit, A58H, takes the most time to be fully charged, i.e., 6.43 h for the fastest feed rate, while the A53 unit charges the fastest, at 4.25 h. The behavior of P53 lies in between A53 and A58H, considering stored energy and charging time. During discharging, all PCMs could provide an adequate DHW amount, even in the worst case, that is, a small unit with a high hot water consumption rate. The A58H unit provides hot water above 40 °C for 10 min, P53 for 11 min, and A53 for 12 min. The DHW production duration increased if a bigger unit was used or if the consumption rate was lower. [ABSTRACT FROM AUTHOR]

An innovative thermal energy storage system (TESSe2b) was retrofitted in a residential building in Cyprus with a typical Mediterranean climate. The system comprises flat-plate solar collectors, thermal energy storage tanks filled with organic phase change material, a geothermal installation consisting of borehole heat exchangers with and without phase change material and a ground source heat pump, an advanced self-learning control system, backup devices and several other auxiliary components. The thermal energy storage tanks cover the building's needs at certain temperature ranges (10–17 °C for cooling, 38–45 °C for heating and 50–60 °C for domestic hot water). A performance evaluation was conducted by comparing the TESSe2b system with the existing conventional heating and cooling system. The systems were simulated using commercial software, and the performance of the systems and the building's energy needs were calculated. Based on the energy quantities, an economic analysis followed. The equivalent annual primary energy consumption with the conventional system resulted in being 43335 kWh, while for the storage system, it was only 8398 kWh. The payback period for the storage system was calculated to be equal to 9.76 years. The operation of the installed storage system provided data for calculations of the seasonal performance factor and storage performance. The seasonal performance factor values were very high during June, July and August, since the TESSe2b system works very efficiently in cooling mode due to the very high temperatures that dominate in Cyprus. The measured stored thermal energy for cooling, heating and domestic hot water resulted in being 14.5, 21.9 and 6.2 kWh, respectively. Moreover, the total volume of the phase change material thermal energy storage tanks for heating and domestic hot water was calculated to be roughly several times smaller than the volume of a tank with water as a storage medium. [ABSTRACT FROM AUTHOR]