Search

The key objective of this study is to determine the effect of interphase boundaries, the formation of which is caused by the variation of Li2ZrO3/MgLi2ZrO4 phases in lithium-containing ceramics based on lithium metazirconate, on the resistance to near-surface layer destruction processes associated with irradiation with He2+ ions. During the observation of the deformation effects that have an adverse impact on the volumetric swelling of the near-surface layers of ceramics, the thermal expansion factor caused by high-temperature irradiation was considered, simulating conditions as close as possible to the operating conditions of these materials as blankets for tritium propagation. During the studies conducted, it was established that an elevation in the contribution of MgLi2ZrO4 in the composition of ceramics leads to a rise in resistance to deformation swelling caused by structural distortions of the crystal lattice, due to a decrease in the effect of thermal expansion, alongside the presence of interphase boundaries. The established dependencies of the change in the hardness of the near-surface layer of the studied ceramics made it possible to establish the kinetics of softening caused by the deformation distortion of the crystalline structure, as well as to determine the relationship between volumetric swelling and softening (change in hardness) and a decrease in crack resistance (change in the value of resistance to single compression). [ABSTRACT FROM AUTHOR]

The aim of this study is to determine the effect of changes in the phase composition of Al2O3–Si3N4 ceramics that were obtained using the method of mechanochemical solid-phase grinding on their resistance to the process of long-term thermal exposure, accompanied by the processes of oxidation and softening. The relevance of this research consists of determining the influence of the phase composition of ceramics on the change in their strength and thermophysical parameters, on the basis of which, we can draw a conclusion about the optimal composition of composite ceramics that have great prospects in the field of fire-resistant, heat-resistant, or radiation-resistant structural materials. During this study, the dynamics of the changes in the phase transformations of the xAl2O3–(1−x)Si3N4 ceramics, with variations in the ratio of the components, initiated by the thermal annealing of the samples, was established. According to the assessment of the phase transformations with variations in the ratio of the components, it was found that thermal annealing in an air environment at an Al2O3 concentration in the order of 0.3–0.5 M leads to the formation of an orthorhombic Al2(SiO4)O phase and an elevation in its contribution at concentrations above 0.5 M, which causes a rise in the thermophysical parameters and resistance to high-temperature degradation. During the heat resistance tests, it was found that the formation of the composite ceramics with the Si3N4(SiO2)/Al2(SiO4)O/Al2O3 phase composition results in an increase in the stability of their strength properties when exposed to thermally induced oxidation, which has a negative impact on their resistance to softening and a decrease in hardness. Moreover, the presence of the Al2(SiO4)O phase in the composition of the ceramics causes a slowdown in the processes of thermal oxidation of the Si3N4 phase under prolonged temperature exposure, alongside an increase in the degradation resistance of strength properties by more than 4–7 times, in comparison with the softening data established for single-component ceramics. [ABSTRACT FROM AUTHOR]

The study investigates alterations in the mechanical and thermophysical properties of ceramics composed of xLi2ZrO3–(1−x)Li4SiO4 as radiation damage accumulates, mainly linked to helium agglomeration in the surface layer. This research is motivated by the potential to develop lithium-containing ceramics characterized by exceptional strength properties and a resistance to the accumulation of radiation damage and ensuing deformation distortions in the near-surface layer. The study of the radiation damage accumulation processes in the near-surface layer was conducted through intense irradiation of ceramics using He2+ ions at a temperature of 700 °C, simulating conditions closely resembling operation conditions. Following this, a correlation between the accumulation of structural modifications (value of atomic displacements) and variations in strength and thermophysical characteristics was established. During the research, it was observed that two-component ceramics exhibit significantly greater resistance to external influences and damage accumulation related to radiation exposure compared to their single-component counterparts. Furthermore, the composition that provides the highest resistance to softening in two-component ceramics is an equal ratio of the components of 0.5Li2ZrO3–0.5Li4SiO4 ceramics. [ABSTRACT FROM AUTHOR]

This paper presents the results of the influence of variation of the synthesis conditions of CuBi/CuBi2O4 films with a change in the applied potential difference, as well as a change in electrolyte solutions (in the case of adding cobalt or nickel sulfates to the electrolyte solution) on changes in the phase composition, structural parameters and strength characteristics of films obtained using the electrochemical deposition method. During the experiments, it was found that, in the case of the addition of cobalt or nickel to the electrolyte solutions, the formation of films with a spinel-type tetragonal CuBi2O4 phase is observed. In this case, a growth in the applied potential difference leads to the substitution of copper with cobalt (nickel), which in turn leads to an increase in the structural ordering degree. It should be noted that, during the formation of CuBi/CuBi2O4 films from solution–electrolyte №1, the formation of the CuBi2O4 phase is observed only with an applied potential difference of 4.0 V, while the addition of cobalt or nickel sulfates to the electrolyte solution results in the formation of the tetragonal CuBi2O4 phase over the entire range of the applied potential difference (from 2.0 to 4.0 V). Studies have been carried out on the strength and tribological characteristics of synthesized films depending on the conditions of their production. It has been established that the addition of cobalt or nickel sulfates to electrolyte solutions leads to an increase in the strength of the resulting films from 20 to 80%, depending on the production conditions (with variations in the applied potential difference). During the studies, it was established that substitution of copper with cobalt or nickel in the composition of CuBi2O4 films results in a rise in the shielding efficiency of low-energy gamma radiation by 3.0–4.0 times in comparison with copper films, and 1.5–2.0 times for high-energy gamma rays, in which case the decrease in efficiency is due to differences in the mechanisms of interaction of gamma quanta, as well as the occurrence of secondary radiation as a result of the formation of electron–positron pairs and the Compton effect. [ABSTRACT FROM AUTHOR]

The article outlines findings from a comparative analysis of the effectiveness of doping CeO2 ceramics with a stabilizing additive Y2O3 on alterations in the strength and thermophysical parameters of ceramics under high-temperature irradiation with heavy ions comparable in energy to fission fragments of nuclear fuel, which allows, during high-temperature irradiation, to simulate radiation damage that is as similar as possible to the fission processes of nuclear fuel. During the studies, it was found that the addition of a stabilizing additive Y2O3 to the composition of CeO2 ceramics in the case of high-temperature irradiation causes an increase in stability to swelling and softening because of a decrease in the thermal expansion of the crystal lattice by 3–8 times in comparison with unstabilized CeO2 ceramics. It has been determined that the addition of a stabilizing additive Y2O3 leads not only to a rise in the resistance of the crystal structure to deformation distortions and swelling, but also to a decrease in the effect of thermal expansion of the crystal structure, which has an adverse effect on the structural ordering of CeO2 ceramics exposed to irradiation at high temperatures. [ABSTRACT FROM AUTHOR]

The work is devoted to the study of the use of AlN–TiO2 coatings as protective materials against corrosion and natural aging, as well as a rise in wear resistance of the steel surface under long-term mechanical influences. The choice of oxy-nitride coatings obtained by magnetron sputtering by layer-by-layer deposition of layers of aluminum nitride and titanium oxide with layer thicknesses of the order of 50 nm and 100 nm as objects of study is due to their high resistance to external influences, which can have a significant impact on growth in the resistance to degradation processes associated with hydrogenation during the operation of steel structures. During determination of the hydrophobicity/hydrophilicity of AlN–TiO2 coatings, it was found that the applied coatings, regardless of the conditions for their preparation, have hydrophobic properties (the contact angle is ~125–130°), which are preserved both during corrosion tests (except for TiO2 coatings, for which the change in the contact angle after corrosion tests is ∆ ~ 10°) and when modeling natural aging processes. During the tribological tests of coating samples, it was found that a growth in the number of spray layers (when alternating them) leads to a rise in wear resistance, both in the case of the initial samples and for samples subjected to corrosion in a model solution of 0.1 M NaCl and when simulating natural aging processes. [ABSTRACT FROM AUTHOR]

Ceramics based on zirconium dioxide are very important compounds for dental, implant, and structural material applications. Despite the fact that tetragonally stabilized YSZ has been well studied, the search for new compositions of zirconia-based ceramics is still in progress. The ZrO2-CeO2 system is one of the alternatives for YSZ materials, but there is conflicting experimental data on its phase composition and mechanical properties depending on the ratio of components. In this study, we investigated the phase composition, and microstructural, mechanical, and physical properties of (1 − x)∙ZrO2-x∙CeO2 (step of x = 0.05) ceramics obtained by the solid-state sintering process from micron-sized powders. For the characterization of samples, XRD, Raman spectroscopy, SEM, the Vickers Microhardness Test, and dielectric spectroscopy were implemented. The results showed that by varying the CeO2 concentration, it is possible to synthesize stable tetragonal ZrO2 at room temperature with a high microhardness HV0.05 value of ~1500, low porosity (~2.5%), and a high dielectric constant of 36. The pronounced combined effect of tetragonal phase formation, densification, and grain size reduction on the mechanical and dielectric properties of the experimental samples was investigated. Refined experimental data make it possible to synthesize high-quality zirconia–ceria ceramics for use as refractories, dispersed nuclear fuel, or solid oxide fuel cells. [ABSTRACT FROM AUTHOR]