Search

Introduction: Production of strawberries in greenhouses and polytunnels is gaining popularity worldwide. This study investigated the effect of reuse of coir and peat, two substrates commonly adapted to soilless strawberry production, as well as stand-alone wood fiber from Norway spruce, a promising substrate candidate. Methods: The experiment was performed in a polytunnel at NIBIO Apelsvoll, Norway, and evaluated both virgin substrates, as well as spent materials that were used in one or two years. Yield, berry quality and plant architecture of the strawberry cultivar 'Malling Centenary' were registered. In addition, chemical and physical properties of virgin and reused substrates were investigated. Results: While plants grown in peat and wood fiber had highest yield in the first year of production, the berry yield was slightly reduced when these substrates were utilized for the second and third time. However, yield was comparable to the yield level attained in new and reused coir. Interestingly, berries grown in wood fiber had a tendency to a higher sugar accumulation. This substrate also produced the highest plants. Stand-alone wood fiber was the substrate with the highest accumulation of nitrogen during the three consecutive production cycles. All three investigated materials revealed a trend for decreased potassium accumulation. Wood fiber is characterized by the highest percentage of cellulose, however after three years of production the cellulose content was reducedto the same levels as for coir and peat. Discussion: Implementation of wood fiber as a growing medium, as well as general practice of substrate reuse can be therefore an achievable strategy for more sustainable berry production. [ABSTRACT FROM AUTHOR]

Cultivation of strawberries in greenhouses and polytunnels is increasing, and new sustainable growing media are needed to replace peat and coconut coir. This study investigated the effect of wood fiber and compost as growing media on hydroponically cultivated strawberries. Two experiments were conducted, where the everbearing cultivar 'Murano' was grown in mixtures of wood fiber and compost (Experiment 1) and the seasonal flowering cultivar 'Malling Centenary' was grown in mixtures of wood fiber and peat (Experiment 2). Additionally, in Experiment 2, the effect of adding start fertilizer was assessed. The yield potential of 'Murano' plants was maintained in all substrates compared to the coconut coir control. However, a mixture of 75% wood fiber and 25% compost produced the highest yield, suggesting that mixtures of nutritious materials with wood fiber may improve plant performance. The chemical composition of the berries was not affected by the substrate composition; however, berries from plants grown in the best performing blend had a lower firmness than those grown in coconut coir. 'Malling Centenary' plants produced higher yields in substrates enriched with start fertilizer. Generally, the productivity of 'Malling Centenary' plants was maintained in blends containing up to 75% of wood fiber mixture even without start fertilizer. [ABSTRACT FROM AUTHOR]

It has been long known that thermal imaging may be used to detect stress (e.g. water and nutrient deficiency) in growing crops. Developments in microbolometer thermal cameras, such as the introduction of imaging arrays that may operate without costly active temperature stabilization, have vitalized the interest in thermal imaging for crop measurements. In this study, we have focused on the challenges occurring when temperature stabilization is omitted, including the effects of focal-plane-array (FPA) temperature, camera settings and the environment in which the measurements are performed. Further, we have designed and tested models for providing thermal response from an analog LWIR video signal (typical output from low-cost microbolometer thermal cameras). Finally, we have illustrated and discussed challenges which typically occur under practical use of thermal imaging of crops, by means of three cereal showcases, including proximal and remotely based (UAV) data acquisition. The results showed that changing FPA temperature greatly affected the measurements, and that wind and irradiance also appeared to affect the temperature dynamics considerably. Further, we found that adequate settings of camera gain and offset were crucial for obtaining a reliable result. The model which was considered best in terms of transforming video signals into thermal response data included information on camera FPA temperature, and was based on a priori calibrations using a black-body radiation source under controlled conditions. Very good calibration (r2>0.99, RMSE=0.32°C, n=96) was obtained for a target temperature range of 15-35°C, covering typical daytime crop temperatures in the growing season. However, the three showcases illustrated, that under practical conditions, more factors than FPA temperature may need to be corrected for. In conclusion, this study shows that thermal data acquisition by means of an analog, uncooled thermal camera may represent a possible, cost-efficient method for the detection of crop stress, but appropriate corrections of disturbing factors are required in order to obtain sufficient accuracy. [ABSTRACT FROM AUTHOR]

The article focuses on indirect measurement of water status, nitrogen deficiency, leaf diseases, and weed patches in the field which may allow nitrogen application rates. Topics discussed include comprehensive assessment of a cropping system multisensory data collection and data fusion are the emerging technologies, use of indirect sensor measurements for determination of water and nitrogen status, and disease and weed infestations in wheat and selection of data pre-processing.