Search

Under the sponsorship of the U.S. National Science Foundation, a workshop on emerging research opportunities in ceramic and glass science was held in September 2016. Reported here are proceedings of the workshop. The report details eight challenges identified through workshop discussions: Ceramic processing: Programmable design and assembly; The defect genome: Understanding, characterizing, and predicting defects across time and length scales; Functionalizing defects for unprecedented properties; Ceramic flatlands: Defining structure-property relations in free-standing, supported, and confined two-dimensional ceramics; Ceramics in the extreme: Discovery and design strategies; Ceramics in the extreme: Behavior of multimaterial systems; Understanding and exploiting glasses and melts under extreme conditions; and Rational design of functional glasses guided by predictive modeling. It is anticipated that these challenges, once met, will promote basic understanding and ultimately enable advancements within multiple sectors, including energy, environment, manufacturing, security, and health care.

SiC‐fiber–reinforced SiC matrix composite cladding for light water reactor fuel elements must withstand high‐temperature steam oxidation in a loss‐of‐coolant accident scenario (LOCA). Current composite designs include an outer monolithic SiC layer, in part, to increase steam oxidation resistance. However, it is not clear how such a structure would behave under high‐temperature steam in the case when the monolithic layer cracks and carbon interphases and SiC fibers are exposed to the environment. To fill this knowledge gap, stress‐rupture tests of prototypic SiC composite cladding at 1000°C under steam and inert environments were conducted. The applied stress was ∼120 MPa, which was beyond the initial cracking stress. The failure lifetime under steam was 400–1300 s, while 75% of the composite specimens did not fail after 3 h of total exposure under inert gases. Microstructural observations suggest that steam oxidation activated slow crack growth in the fibers, which led to failure of the composite. The results from this study suggest that stress rupture in steam environments could be a limiting factor of the cladding under reactor LOCA conditions. [ABSTRACT FROM AUTHOR]

In this paper, we study the elastic properties of the entropy-stabilized oxide (Mg, Co, Ni, Cu, Zn)O using experimental and first principles techniques. Our measurements of the indentation modulus on grains with a wide range of crystallographic orientations of the entropy-stabilized oxide revealed a high degree of elastic isotropy at ambient conditions. First principles calculations predict mild elastic anisotropy for the paramagnetic structure, which decreases when the system is considered to be non-magnetic. When the antiferromagnetic state of CoO, CuO, and NiO is accounted for in the calculations, a slight increase in elastic anisotropy is observed, suggesting a coupling between magnetic ordering and the orientation dependent elastic properties. Furthermore, an examination of the local structure reveals that the isotropy is favored through local ionic distortions of Cu and Zn—due to their tendencies to form tenorite and wurtzite phases. The relationships between the elastic properties of the multicomponent oxide and those of its constituent binary oxides are reviewed. These insights open up new avenues for controlling isotropy for technological applications through tuning composition and structure in the entropy-stabilized oxide or the high-entropy compounds in general. [ABSTRACT FROM AUTHOR]

The internal friction and creep deformation behavior of La0.8Ca0.2CoO3 and pure LaCoO3 mixed ionic electronic conducting perovskite ceramics have been studied by Dynamic Mechanical Analysis and uniaxial compression under constant applied load, respectively. It was found that both the internal friction and creep strain were almost an order of magnitude higher for Ca2+ doped LaCoO3 as compared to pure undoped LaCoO3. The difference in Ca2+ doped LaCoO3 behavior was attributed to the much higher concentration of point defects (e.g., oxygen vacancies) in the structure and their interaction with other mobile defects, such as ferroelastic domain/twin walls, stacking faults, dislocations, etc. Such interactions of numerous point defects with domain walls produce energetic barriers and slow down the movement of ferroelastic domain walls under applied stress. At the same time, the defects' interactions increase the internal friction resulting in a much higher creep strain of La0.8Ca0.2CoO3 as compared to pure LaCoO3, as the creep strain is determined by the distance between the domain wall and its equilibrium position at the onset of the creep process. Therefore, the high friction will result in the larger distance the wall has to move to reach the equilibrium which in turn results in higher creep strain. The expansion of LaCoO3 under constant applied compressive stress, named here as negative creep, was also discovered to occur during room temperature creep experiments. [ABSTRACT FROM AUTHOR]