Search

Exploring Ocean and Ice Worlds could help us to understand the origin and evolution of life in the universe. In our solar system we have identified six Ocean and Ice Worlds, namely Earth, Europa, Ganymede, Callisto, Enceladus, and Titan. Other potential targets include Dione, Triton, and Pluto. As documented in the Planetary Decadal Survey [1] and the NASA Roadmap to Ocean Worlds [2], these worlds are compelling science destinations, with oceans situated below their tens of kilometers thick ice shells. To reach them we need a new exploration paradigm with novel technological solutions. Key technological challenges revolve around the power for the probe and for melting, as well as protecting the payload against the extreme environments, including high pressure, low temperature, corrosion, and radiation. Far away from the Sun, and melted into the ice, we may only rely on long-lived internal power generation. Radioisotope Power Systems (RPS) with either static or dynamic conversion, utilizing the heat of decaying Plutonium-238, could be good candidates. We need suitable payloads that are protected and could survive the extreme environments, as well as enabling power and thermal systems for melting through the ice shield and to swim in the ocean below the ice. RPS could support the probe’s instruments and sub-systems, as well as provide a heat source for melting the ice while keeping the components at operating temperatures. Mitigating the external pressure while immersing inside the ice shell, and in the ocean, would require a new RPS design that operates inside a Pressure Vessel. In our paper, we will discuss general mission architecture trades and the sizing of a next generation RPS housed in a pressure vessel, broadly applicable to any of the Ocean Worlds satellites of interest. Through a technology focused approach, we address interconnected design and mission architecture aspects, including considerations for: the RPS and the Pressure Vessel; extreme environmental constraints; g-load tolerance; power and thermal systems sizing for science measurements; spacecraft operations through all mission phases; subsurface mobility; and planetary protection. The findings will inform the science community on instrument accommodation possibilities; the mission planning community on possible mission concepts; and the RPS development community on the science driven technology considerations.

The surfaces of Ice Worlds record evidence of interior processes, chemical potential, habitability, and potentially life within the interior. Volatile and organic chemistry at the surface is critical in determining habitability and detecting the presence of past or extant life. Radioisotope Power Systems (RPS) could be an enabling technology for in situ missions to ice worlds, providing both power and heat for long durations where solar power would not be feasible. However, it is necessary to understand the potential impact of RPS upon the local environment, to ensure that the rejected heat from RPS does not compromise science measurements or planetary protection requirements. To address these concerns, an RPS Ice World Lander Study was carried out in 2019 to investigate possible requirements on RPS surface mission concepts and approaches to excess heat management. The study focused on two destinations that are representative of the range of potential environments: Europa and Enceladus.Initial analysis showed that, due to the very low pressures on the surfaces of most ice world targets, surface melting does not occur because the water ice does not meet the triple-point. A 4 kW heat source suspended above the surface of Europa or Enceladus would not cause any melting, only sublimation.The study used a surface sublimation limit of 10 cm over a two-year period (the baseline for the recent Europa Lander study). To stay within this limit, Europa, with its relatively warm surface, could tolerate only 10 W/m2 of surface heat flux. Enceladus, with its relatively cold pure ice composition, could tolerate up to 100 W/m2.Various lander and heat shield configurations were analyzed for their heat flux radiated from the RPS to the surface. For a given heat shield configuration, the study team determined the minimum height of the RPS above the surface for which the heat flux would be within the accepted parameters for Europa and for Enceladus. Based on these thermal analyses, such RPS-powered landers could remain compliant with science investigation and planetary protection requirements with only modest mass allocated to spacecraft thermal accommodations.

As the interest in exploring icy and ocean worlds gains increasing traction among scientists and mission communities, there are many potential icy and ocean world targets for in-situ lander missions. Potential targets include Europa, Enceladus, Titan, Triton, Ceres, Pluto, and more, which will allow the scientific community to address icy and ocean world related questions for understanding the distribution of life in the Solar System. Beyond Jupiter, solar power is infeasible for any landed missions and primary batteries are infeasible for long-duration missions. Radioisotope Power Systems (RPS) can be enabling for these long-duration in-situ missions. However, the interaction of RPS waste heat with icy world surfaces must be understood to assure the science and mission communities that RPS are a safe, enabling option to explore the surface of icy bodies. This paper describes a study for the RPS Program that was conducted by the RPS Mission Analysis Team and JPL’s Team X to investigate the system-level impact of a heat rejection system that would be required for RPS-enabled exploration of icy and ocean worlds.

UNKNOWN

The NASA Radioisotope Power Systems (RPS) Program Mission Analysis Team at the Jet Propulsion Laboratory (JPL) requested a JPL Innovation Foundry Architecture Team (A-Team) study to assess mission pull for small RPS (1 mWe - 40 We) in order to inform the RPS Program Office on what future power system developments should be focused on. The A-Team is JPL’s concurrent engineering design team for science definition and early mission concept development, targeting concept maturation levels of 1 through 3. The requested small RPS study was tasked to identify the architecture space of potential small RPS missions, and suggest power levels that could enable or enhance potential future small spacecraft missions. This paper describes the collaborative engineering processes that the A-Team and Mission Analysis Team used to reach results quickly and the findings to inform the RPS Program about mission concept power requirements on RPS for small missions.

UNKNOWN