Search

The low thermal conductivity of β-Ga2O3 is a significant concern for maximizing the potential of this ultra-wide bandgap semiconductor as a power switching device technology. Here, we report on the use of nanocrystalline diamond (NCD) deposited via microwave plasma enhanced chemical vapor deposition (MP-CVD) as a top-side, device-level thermal management solution on a lateral β-Ga2O3 transistor. NCD was grown via MP-CVD on β-(AlxGa1−x)2O3/β-Ga2O3 heterostructures prior to the gate formation of the field-effect transistor. A reduced growth temperature of 400 °C and a SiNx barrier layer were used to protect the oxide semiconductors from etching in the MP-CVD H2 plasma environment. Raman spectroscopy showed a highly sp3-bonded NCD film was obtained at 400 °C, with grain size of about 50–100 nm imaged via atomic force microscopy. The incorporation of the NCD heat-spreading layer resulted in a β-(AlxGa1−x)2O3/β-Ga2O3 heterostructure field-effect transistor showing a decrease in the total thermal resistance at the gate by 42%. The fabrication process, including the NCD etch in the gate region, will need to be improved to minimize the impact of these processes on important device characteristics (i.e., drain current, threshold voltage, and leakage current). [ABSTRACT FROM AUTHOR]

This work demonstrates direct, rapid 2D thermal mapping measurement capabilities of the ultrawide bandgap semiconductor channel of lateral β-(AlxGa1−x)2O3/Ga2O3 transistors without sample contamination, long acquisition times, or sophisticated thermometry such as developing deep-ultra-violet compatible thermoreflectance systems. The temperature rise in the channel of a β-(Al0.21Ga0.79)2O3/Ga2O3 heterostructure field-effect transistor (HFET) was mapped using thermoreflectance imaging at 470 nm. First, the thermoreflectance response of the HFET channel was measured using a monochromator, revealing a maximum of the reflectance change around 470–480 nm. Thermoreflectance calibrations were then performed at 470 nm (peak of the reflectance change) and yielded an average thermoreflectance coefficient of 1.06 ± 0.07 × 10−4 K−1. Subsequent measurements of the device (power densities of 0.15–1.47 W/mm and gate-source voltage of 0 V) enabled extraction of a device-level thermal resistance of 51.1 mm·K/W in the channel at the drain-side of the gate. High-resolution, in situ scanning thermal microscopy measurements of the channel temperature rise show good agreement with and further support the thermoreflectance measurements. Finally, the thermal profile across the entire device length (metal electrodes and semiconductor channel) and width was simultaneously measured using thermoreflectance imaging at 470 nm, and the peak temperature rise was measured in the channel at the drain-side of the gate electrode. [ABSTRACT FROM AUTHOR]

The effect of heteroepitaxial β-(AlxGa1−x)2O3 film thickness and Al content on surface morphology was characterized to experimentally determine the critical thickness limitations of the (010) β-(AlxGa1−x)2O3/Ga2O3 heterostructure. High-resolution x-ray diffraction was used to assess the strain state of the films; reciprocal space mapping (RSM) revealed that even cracked films were still fully strained. In cracked films, diffuse scattering was observed in RSMs, indicating lattice tilting. Cracking of the films was investigated using atomic force microscopy (AFM), x-ray topography (XRT), bright-field scanning transmission electron microscopy (BF-STEM), and high-resolution transmission electron microscopy. Using both AFM and XRT, the [001] direction was observed to be the most prevalent crack direction; however, cracks were also observed in the [100] direction. In uncracked regions of the films, XRT revealed the alignment of threading dislocations along the [001] direction. Cross-sectional imaging of the crack geometry and propagation was performed using BF-STEM, and it was observed that the cracks in the [001] direction extended through the thickness of the β-(AlxGa1−x)2O3 film (∼205 nm) and a further ∼100–200 nm into the β-Ga2O3 substrate. Experimental data for critical film thickness showed good agreement with previous theoretical calculations based on the Griffith criterion for crack propagation. [ABSTRACT FROM AUTHOR]

Herein, the electrical and thermal performance of lateral AlGaN/GaN high electron mobility transistors (HEMTs) and metal‐insulator‐semiconductor field effect transistors (MISFETs) fabricated with 11 μm thick GaN buffer layers on 200 mm diameter Qromis Substrate Technology (QST) substrates are investigated. The QST substrate has a polycrystalline core engineered to be coefficient of thermal expansion (CTE)‐matched to GaN to minimize wafer bow and residual stress in the GaN film as a result of epitaxial growth. Raman spectroscopy is used to determine the biaxial residual stress in the GaN buffer of the as‐fabricated devices. Electrical characterization is demonstrated on the HEMTs including DC and pulsed output characteristics, DC transfer characteristics, Hall mobility, carrier concentration, sheet resistance, median transition frequency, and maximum stable gain. Finally, the thermal performance of the AlGaN/GaN MISFET is assessed via thermoreflectance thermal imaging at DC power densities up to 19 W mm−1. The thermal resistance of the MISFET, calculated using the peak temperature rises on the gate electrode for DC power densities <10 W mm−1, is measured to be 15.4 mm K W−1, which is comparable with state‐of‐the‐art GaN‐on‐Si lateral transistors. [ABSTRACT FROM AUTHOR]

In this study, the Raman biaxial stress coefficients KII and strain-free phonon frequencies ω0 have been determined for the E2 (low), E2 (high), and A1 (LO) phonon modes of aluminum nitride, AlN, using both experimental and theoretical approaches. The E2 (high) mode of AlN is recommended for the residual stress analysis of AlN due to its high sensitivity and the largest signal-to-noise ratio among the studied modes. The E2 (high) Raman biaxial stress coefficient of −3.8 cm−1/GPa and strain-free phonon frequency of 656.68 cm−1 were then applied to perform both macroscopic and microscopic stress mappings. For macroscopic stress evaluation, the spatial variation of residual stress was measured across an AlN-on-Si wafer prepared by sputter deposition. A cross-wafer variation in residual stress of ∼150 MPa was observed regardless of the average stress state of the film. Microscopic stress evaluation was performed on AlN piezoelectric micromachined ultrasonic transducers (pMUTs) with submicrometer spatial resolution. These measurements were used to assess the effect of device fabrication on residual stress distribution in an individual pMUT and the effect of residual stress on the resonance frequency. At ∼20 μm directly outside the outer edge of the pMUT electrode, a large lateral spatial variation in residual stress of ∼100 MPa was measured, highlighting the impact of metallization structures on residual stress in the AlN film. [ABSTRACT FROM AUTHOR]

The motion of domain walls in lead zirconate titanate (PZT) produces both nonlinearity and hysteresis. While measurements of the resulting self-heating under an electric field drive are well known in bulk ferroelectric ceramics, self-heating effects in PZT films may differ from those in bulk ceramics due to a combination of reduced domain wall motion, differences in heat dissipation associated with substrates or passive elastic layers, and differences in typical drive fields. Here, it is shown that the thermal imaging of the test structures of PZT piezoelectric microelectromechanical systems using techniques such as infrared thermography and thermoreflectance thermal imaging suffers from motion-induced artifacts. These limitations were overcome via nanoparticle-assisted Raman thermometry with a spatial resolution of ∼1 μm. To acquire the local temperature distribution quantitatively, anatase nanoparticles were distributed across the electrodes and actuating PZT diaphragm. The temperature rise of the test structures increased as the operating frequency, voltage amplitude, and slew rate increased. As expected, the largest temperature rises were induced due to self-heating associated with domain switching under bipolar operation. In addition, a higher voltage amplitude testing revealed non-uniform temperature distributions across the piezoelectric actuator, suggesting that AC Joule heating can induce significant heat generation (ΔT ∼ 30 K) under high electric fields (∼390 kV/cm). [ABSTRACT FROM AUTHOR]

In this report, the thermal performance of a hydrogen (H)-terminated diamond field-effect transistor (FET) is investigated using Raman spectroscopy and electrothermal device modeling. First, the thermal conductivity (κdiamond) of the active diamond channel was determined by measuring the temperature rise of transmission line measurement structures under various heat flux conditions using nanoparticle-assisted Raman thermometry. Using this approach, κdiamond was estimated to be 1860 W/m K with a 95% confidence interval ranging from 1610 to 2120 W/m K. In conjunction with measured electrical output characteristics, this κ was used as an input parameter for an electrothermal device model of an H-terminated diamond FET. The simulated thermal response showed good agreement with surface temperature measurements acquired using nanoparticle-assisted Raman thermometry. These diamond-based structures were highly efficient at dissipating heat from the active device channel with measured device thermal resistances as low as ∼1 mm K/W. Using the calibrated electrothermal device model, the diamond FET was able to operate at a very high power density of 40 W/mm with a simulated temperature rise of ∼33 K. Finally, the thermal resistance of these lateral diamond FETs was compared to lateral transistor structures based on other ultrawide bandgap materials (Al0.70Ga0.30N, β-Ga2O3) and wide bandgap GaN for benchmarking. These results indicate that the thermal resistance of diamond-based lateral transistors can be up to ∼10× lower than GaN-based devices and ∼50× lower than other UWBG devices. [ABSTRACT FROM AUTHOR]

AlN thin films are enabling significant progress in modern optoelectronics, power electronics, and microelectromechanical systems. The various AlN growth methods and conditions lead to different film microstructures. In this report, phonon scattering mechanisms that impact the cross-plane (κz; along the c-axis) and in-plane (κr; parallel to the c-plane) thermal conductivities of AlN thin films prepared by various synthesis techniques are investigated. In contrast to bulk single crystal AlN with an isotropic thermal conductivity of ∼330 W/m K, a strong anisotropy in the thermal conductivity is observed in the thin films. The κz shows a strong film thickness dependence due to phonon-boundary scattering. Electron microscopy reveals the presence of grain boundaries and dislocations that limit the κr. For instance, oriented films prepared by reactive sputtering possess lateral crystalline grain sizes ranging from 20 to 40 nm that significantly lower the κr to ∼30 W/m K. Simulation results suggest that the self-heating in AlN film bulk acoustic resonators can significantly impact the power handling capability of RF filters. A device employing an oriented film as the active piezoelectric layer shows an ∼2.5× higher device peak temperature as compared to a device based on an epitaxial film. [ABSTRACT FROM AUTHOR]

Improvements in radio frequency and power electronics can potentially be realized with ultrawide bandgap materials such as aluminum gallium nitride (AlxGa1−xN). Multidimensional thermal characterization of an Al0.30Ga0.70N channel high electron mobility transistor (HEMT) was done using Raman spectroscopy and thermoreflectance thermal imaging to experimentally determine the lateral and vertical steady-state operating temperature profiles. An electrothermal model of the Al0.30Ga0.70N channel HEMT was developed to validate the experimental results and investigate potential device-level thermal management. While the low thermal conductivity of this III-N ternary alloy system results in more device self-heating at room temperature, the temperature insensitive thermal and electrical output characteristics of AlxGa1−xN may open the door for extreme temperature applications. [ABSTRACT FROM AUTHOR]

Ultra-wide bandgap β-gallium oxide (Ga2O3) devices are of considerable interest with potential applications in both power electronics and radio frequency devices. However, current Ga2O3 device technologies are limited by the material's low intrinsic electron mobility and thermal conductivity. The former problem can be addressed by employing modulation-doped β-(AlxGa1−x)2O3/Ga2O3 heterostructures in the device architecture. In this work, (AlxGa1−x)2O3/Ga2O3 modulation-doped field effect transistors (MODFETs) have been investigated from a thermal perspective. Thermoreflectance thermal imaging was used to characterize the self-heating of the MODFETs. The (Al0.18Ga0.82)2O3 thermal conductivity (3.1–3.6 W/mK) was determined using a frequency domain thermoreflectance technique. Electro-thermal modeling was used to discern the effect of design parameters such as substrate orientation and channel length on the device self-heating behavior. Various thermal management schemes were evaluated using the electro-thermal device model. From an electro-thermal co-design perspective, the improvement in electrical performance followed by the mitigation of self-heating was also studied. For example, by employing a Ga2O3-on-SiC composite wafer, which was fabricated in this work, a 50% increase in power handling capability can be achieved as compared to a homoepitaxial device. Furthermore, flip-chip heterointegration and double-sided cooling approaches can lead to more than 2× improvement in the power handling capability. Using an augmented double-sided cooling design that includes nanocrystalline diamond passivation, a 5× improvement in the power handling capability can be accomplished, indicating the potential of the technology upon implementation of a suitable thermal management scheme. [ABSTRACT FROM AUTHOR]

We investigate the effect of strain on the two-dimensional electron gas (2DEG) channel in a flexible Al0.25Ga0.75N/GaN high-electron-mobility transistor (HEMT) by mechanical bending to prove the concept of active polarization engineering to create multifunctional electronic and photonic devices made of flexible group III-nitride thin films. The flexible HEMTs are fabricated by a layer-transfer process and integrated with a 150-μm-thick Cu film. The strain values are estimated from high-resolution x-ray diffraction and Raman spectroscopy in 4-cm bend-down and −4-cm bend-up test conditions. The strain-induced piezoelectric polarization can alter the charge density of the 2DEG in the channel at the AlGaN/GaN interface and thus modify the output characteristics of the flexible HEMTs. Accordingly, output characteristics show an increase in output current by 3.4% in the bend-down condition and a decrease by 4.3% in the bend-up condition. Transfer characteristics show a shift of threshold voltage, which also supports the 2DEG channel modulation during bending. Computational simulation based on the same structure confirms the same current modulation effect and threshold voltage shift. Furthermore, the electrical characteristics of the flexible HEMTs show a repeatable dependence on the strain effect, which offers potential for electro-mechanical device applications. [ABSTRACT FROM AUTHOR]

AlGaN/GaN high electron mobility transistors on QST engineered substrates are grown with different GaN/AlGaN buffer layer thickness. The as‐grown heterostructures are evaluated for their structural quality via atomic force microscopy, high‐resolution X‐ray diffraction, Raman spectroscopy, and steady‐state thermoreflectance. Transistor devices are fabricated and evaluated via DC and pulsed electrical techniques, as well as thermoreflectance imaging. It is reported that buffer layer thickness of at least 10 μm can result in lateral high electron mobility transistors (HEMTs) with simultaneously high GaN quality, low stress, good DC electrical performance, low current collapse, and low thermal resistance. [ABSTRACT FROM AUTHOR]

Silicon (Si) is a common n-type donor in AlxGa1-xN; however, it induces bending of edge-type threading dislocations which can generate tensile stress in the film leading to the formation of channeling cracks in thick layers. Germanium (Ge) has previously been investigated as an alternative to Si for n-type doping of GaN, but its impact on film stress in AlxGa1-xN has not been investigated in detail. In this study, we employ in situ wafer curvature measurements combined with postgrowth characterization to investigate Ge doping of AlxGa1-xN (x = 0–0.62) layers grown on 6H-SiC by metalorganic chemical vapor deposition. It was found that Ge doping (n ∼ 1.6 × 1019 cm−3) of Al0.30Ga0.70N does not induce tensile stress during growth in contrast to that observed with a similar level of Si doping. In addition, the average inclination angle of edge dislocations was similar for undoped and Ge doped films indicating that Ge does not promote surface-mediated dislocation climb. High n-type doping was achieved in Ge doped AlxGa1-xN for lower Al fraction range (x < 0.5), but resistivity increased and carrier density decreased significantly for higher Al fractions. The results demonstrate Ge doping as a viable alternative to Si doping of AlxGa1-xN (x < 0.5) for achieving thick, crack-free layers. [ABSTRACT FROM AUTHOR]