Search

Purpose: To evaluate the correspondence between output from a new artificial intelligence tool (AIT) and clinician evaluation regarding the immediate loading suitability of dental implants based on insertion torque curves recorded during implant placement in an in vitro test. The secondary aim was to analyze peak insertion torque (PIT) and variable torque work (VTW) values of the implants., Materials and Methods: The study was performed with four different densities of artificial bone blocks of solid rigid polyurethane without a cortical layer. Five types of implants with different macrogeometries were used. A total of 140 implants (7 implants of each type in the four polyurethane blocks) were inserted. Immediately after implant placement, the insertion torque curves were classified by the operator as suitable (S) or nonsuitable (NS) for immediate loading. The same curves were then analyzed by the new AIT, which classified them as belonging to the 'YES' or 'NO' class. For each implant, PIT and VTW values were also recorded., Results: The correspondence between clinician and AIT evaluation was 99.3%, with only one false negative reported by the algorithm analysis. The AIT was found to have a sensitivity of 98.95%, specificity of 100%, positive predictive value of 100%, and negative predictive value of 97.8%. Mean PIT of the whole sample was 34.19 ± 19.43 Ncm, while mean VTW was 2,266.89 ± 1,993.73 Ncm. Statistically significant differences were found between implant systems in the whole sample and according to density of the polyurethane block., Conclusions: The AIT showed a high level of accuracy in the prediction of immediate loading suitability of dental implants based on the provided insertion torque curves. All the implants used in the in vitro test achieved good levels of primary stability, except when inserted in the least-dense polyurethane block. Clinical studies conducted with larger samples and more clinicians are necessary to confirm these results.

Purpose: To evaluate primary stability of a new dental implant design in low-density bone sites, compare it with another implant design previously studied in the same bone density, and explore possible correlations between primary stability parameters. Materials and Methods: The study was carried out on fresh humid bovine bone classified as type III. The test group consisted of 30 DS Prime Taper implants (PT), and the control group consisted of 30 Astra Tech EV implants (EV). All the implants were inserted according to the protocol provided by the manufacturer. After placement, variable torque work (VTW), peak insertion torque (pIT), and resonance frequency analysis (RFA) were recorded. Results: Mann-Whitney test showed that the mean VTW and pIT were significantly higher in the test group PT compared to the control group EV; furthermore, statistical analysis showed that the mean RFA was slightly higher in the control group EV but without reaching statistical significance. Pearson correlation analysis showed a very strong positive correlation between pIT and VTW values in both groups; furthermore, it showed a positive correlation between pIT and RFA values and between VTW and RFA values again in both groups. Conclusion: The results showed that the novel tapered implants were able to reach good primary stability in low-density bone sites and that this was superior to parallel-walled implants when measured with VTW and pIT. Moreover, a statistically significant correlation was found between the three methods used to measure implant primary stability.

Purpose: To provide a 1-year assessment of friction-retention abutments (Acuris, Dentsply Sirona) used to retain a single lithium disilicate (LS 2 ) monolithic restoration., Materials and Methods: A total of 522 implants were placed to treat single-tooth premolar and molar edentulous sites in the mandible or maxilla. Three types of implants were used. The tested abutments were connected 3 months after implant placement. A single pressed LS 2 monolithic restoration was cemented to a dedicated titanium cap and engaged to the abutment without the use of screws or cement. Any complications affecting the restoration or the opposing dentition, soft tissue dimensional changes, the distance between the implant platform and the bone peak, and pocket probing depths were recorded at the time of restoration placement (T0), after 6 months of function (T1), and after 1 year of function (T2). Esthetic, functional, and biologic parameters were recorded at T0 and T2., Results: A total of 507 patients (284 women and 223 men) received a restoration (T0), and 504 of them reached the T2 1-year follow-up. One restoration fractured after 10 months in function. No statistically significant difference was assessed in the soft tissue measurements or in the measurements of the distance between the supporting implant platform and the bone peak. None of the restorations detached during the observation period., Conclusion: The friction retention abutment is a viable option to retain an implant-supported monolithic LS 2 glass-ceramic restoration in cases of premolar or molar single-tooth edentulism.

Background: In more than three decades of work of the Retrieval Bank of the Laboratory for Undemineralized Hard Tissue Histology of the University of Chieti-Pescara in Italy, many types of biomaterials were received and evaluated. The present retrospective review aimed to evaluate the histological and biological aspects of the evaluated bone substitute biomaterials., Methods: In the present study, the authors prepared a retrospective analysis after the screening of some databases (PubMed, Scopus, and EMBASE) to find papers published from the Retrieval Bank of the Laboratory for Undermineralized Hard Tissue Histology of the University of Chieti-Pescara analyzing only the papers dealing with bone substitute biomaterials and scaffolds, in the form of granules and block grafts, for bone regeneration procedures., Results: Fifty-two articles were found, including in vitro, in vivo, and clinical studies of different biomaterials. These articles were evaluated and organized in tables for a better understanding., Conclusions: Over three decades of studies have made it possible to assess the quality of many bone substitute biomaterials, helping to improve the physicochemical and biological properties of the biomaterials used in daily clinical practice.

Conical retention with antirotational features (Acuris abutment) has been recently proposed for restorations of healed single implants. The conometric abutments use the retentive force of the coping-abutment system to retain the prosthetic crown without the use of cement or screws. This retentive force must be overcome to obtain detachment of the relined provisional crown in immediate restorations. The present article describes the use of digital scanning technology to virtually plan computer-guided implant placement and restoration with conical indexed abutments in postextraction sites. Importing the scan data of both matrix and patrix abutments that are seated on the definitive cast into the computer-aided design software provides a workflow to preoperatively mill a crown that perfectly fits the abutment into the postextraction site. This technique simplifies the provisional crown relining onto the conometric indexed abutment and reduces the intraoperative time.

Purpose: To evaluate the 2-year performance of definitive implant- or tooth-supported three-unit fixed dental prostheses made of zirconia-reinforced lithium silicate placed to restore premolars and molars in clinical cases of partial edentulism., Materials and Methods: All patients received a three-unit fixed restoration made of monolithic, hot-pressed, zirconia-reinforced lithium silicate glass-ceramic. The restoration was cemented to two natural teeth or attached to two 3.5- or 4.5-mm-diameter square threaded, grit-blasted, acid-etched integrated implants with a Morse taper connection. Peri-implant pocket depth and bone and soft tissue remodeling were recorded for 2 years at each follow-up visit. Esthetic, functional, and biologic United States Public Health Services (USPHS) parameters modified by the World Dental Federation study design were assessed yearly until the final follow-up appointment. At the time of placement of the definitive restorations and at the 2-year follow-up visit, the opposing dentitions were identified by type of restoration and supporting structures., Results: A total of 100 patients were consecutively enrolled in the period between June 2016 and July 2017, and 50 patients each received an implant-supported restoration (Group A) or a tooth-supported restoration (Group B). One (2%) of the 50 implant-supported prostheses fractured after 21 months of function. None of the other prostheses failed or became loose or detached. No significant differences involving probing levels or bone and soft tissue remodeling were found between the follow-up times. No cases of inflammation or infection of the mucosal cuff around the neck of the implants were recorded. The most common issue occurred immediately after placement of the prosthesis, when 3 patients (6%) from Group A and 4 patients (8%) from Group B asked for a modification of tooth shade., Conclusion: Implant-supported or tooth-supported three-unit fixed dental prostheses made of zirconia-reinforced lithium silicate can be used to successfully restore cases of posterior partial edentulism. The 2-year results of this report will be studied more in depth in ongoing long-term research.

For decades, the histologic evidence about osseointegration and the bone-implant interface has been discussed in the literature. In this review, the effectiveness of dental implants retrieved for different causes was evaluated. A literature search was performed in databases for papers about implants retrieved from humans published by the Implant Retrieval Center of the University of Chieti-Pescara, Italy. Sixty-eight articles were selected into categories based on topics. The data indicated high level of bone-to-implant contact, lamellar bone close to the surface, roughness related to an increased bone response, organized and remodeled bone after loading, and peri-implant interfaces subjected to a continuous dynamic function.

This report describes the restoration of the healed single implant in the posterior region by using a lithium disilicate crown supported by an Acuris abutment. The restored implants were placed in the premolar and molar region of both the mandible and the maxilla by using a 1-stage approach. The definitive Acuris abutment was placed after an implant healing period of at least 3 months. Definitive impressions were made at least 3 months after surgery. The precrystallized lithium disilicate crown was adapted to a laboratory abutment and evaluated. The crown was then crystallized, finished, colored, and cemented to the definitive abutment by using an adhesive resin cement. The definitive restoration engaged the abutment without the use of screws or cement. A single healed implant can be successfully restored by using a lithium disilicate restoration supported by an Acuris abutment., (Copyright © 2019 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.)

Background : The aim of the present review was to assess the histological and histomorphometrical data from the paper published by our Laboratory on peri-implant bone in dental implants in different loading conditions. Methods : The papers published in different implant loading conditions, in dental implants retrieved from humans, and in the Hard Tissues Research Center of the University of Chieti-Pescara, Italy, were screened on MEDLINE/PubMed, Embase, Scopus, and other electronic databases until 31 December 2018. Only articles that reported the histological and histomorphometrical values of the Bone-Implant Contact (BIC) were selected. Results : The system selection provided a total of 155 papers. The manuscripts included for the narrative review were 57. These papers provided histological and histomorphometrical data. Conclusions : The bone remodeling around dental implants was found to be a dynamic process; loading changed the microstructure of the peri-implant bone; and implants were found to provide a successful function, over several decades, with different range of degrees of BIC in vivo (varying from a little more than 30% to a little more than 90%). Loaded implants presented a 10%-12% higher BIC values when compared to submerged, unloaded implants, and rougher surfaces had, on average, about a 10% higher BIC than machined surfaces.

Aim: The goal of this case series was to evaluate the clinical outcome at the 2-year follow-up of immediately loaded combined screw- and conometric-retained implant-supported full-arch restorations virtually planned using digital scanning technology., Materials and Methods: This series included 12 patients presenting hopeless teeth in the maxilla treated with computer-guided flapless implant placement. A total of 72 implants were inserted. All implants were immediately loaded with a complete-arch restoration supported by an intraorally welded framework. Digital scanning technology was used to virtually plan a combined screw and conometric retention of the frameworks. Clinical parameters were assessed at 1 week and at 1, 3, 6, 12, and 24 months follow-up., Results: The survival rate after 2 years was 98.6%, as one implant failed during the osseointegration period. No major prosthetic complications were observed such as issues with mobility, unscrewed abutments, disconnected conometric copings, and prosthetic fracture. Only one patient registered the chipping of a prosthesis., Conclusion: Based on the results of the present study, the use of combined screw and conometric retention for fixed immediate restorations properly planned using digital scanning technology seems to be a viable treatment alternative to screw or conometric retention alone for immediately loaded rehabilitations.

In guided surgery, implants can be planned from radiographic guide information according to a restoratively driven treatment plan. Unfortunately, the palatal or lingual surface of teeth cannot be easily identified. The present article describes the use of a digitally designed prosthetic shell to improve the accuracy of guided-welded approach planning for immediate restorations supported by conometric abutments. Importing the virtual shell into the planning software provides an effective protocol for using the definitive prosthetic space information to plan the framework shape and position predictably. This method increases the accuracy of virtual planning and reduces the time needed to reline the prosthetic shell., (Copyright © 2019 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.)

Purpose: To evaluate the performance of definitive, implant-supported, lithium disilicate fixed dental prostheses (LS 2 FDPs) manufactured with a computer-assisted design/computer-assisted manufacturing (CAD/CAM) system. All patients received two-unit restorations placed in posterior regions, supported by osseointegrated implants with cone-in-cone connection abutments., Materials and Methods: Two implants (Ankylos) were placed into healed sites or fresh extraction sockets in the maxillary/mandibular posterior regions of partially edentulous patients. Definitive digital impressions were made 3 months after surgery. Twenty-four patients received fixed  monolithic LS 2 restorations manufactured with the CEREC system. All restorations were connected to the implants using cone-in-cone connection abutments. Peri-implant pocket depths were recorded for 2 years at each follow-up visit. Esthetic, functional, and biologic United States Public Health Services (USPHS) parameters modified by the FDI World Dental Federation study design were assessed yearly until the last follow-up appointment. The opposing dentitions were identified by type of restoration and supporting structures at the time of placement of the definitive restorations and at the 2-year follow-up visits., Results: One patient (4.16%) moved to an unknown location during the study. A total of 23 FDPs (95.8%) supported by 46 implants reached the 2-year follow-up. None of the prostheses failed, or became loose or detached. No significant difference involving probing levels between the experimental times were found., Conclusions: The results of this research indicated that the abutment-prostheses connection using a cone-in-cone approach was successful within the 2-year period of this study. None of the studied monolithic LS 2 glass-ceramic prostheses milled using the CEREC CAD/CAM system fractured or became detached., (© 2018 by the American College of Prosthodontists.)

Purpose: The use of the conical coupling connection to support definitive restorations was evaluated in cases involving full acrylic resin or hybrid acrylic resin-composite prostheses. The aim of this study was to evaluate the performance of definitive fixed partial prostheses made with lithium disilicate and supported by coupling connection abutments and healed implants., Materials and Methods: The prostheses were placed in the posterior regions of partially edentulous patients; 65 patients received fixed lithium disilicate restorations splinted with conical coupling connections to two implants. Implants were placed into healed sites and fresh extraction sockets. The prostheses were placed after healing periods of 3 months: restorations were followed yearly for 3 years. At each follow-up visit, peri-implant bone levels and pocket depths were recorded. Esthetic, functional, and biologic United States Public Health Services (USPHS) parameters modified by the FDI World Dental Federation study design were assessed at the last follow-up appointments., Results: Two prostheses (3.07%) fractured: one was related to framework design error; one was caused by a car accident. Three patients reported small chips: these restorations were immediately polished. No significant difference involving peri-implant bone and probing levels between the experimental times were found. None of the prostheses became loose., Conclusions: The results of this research indicated that abutment-prostheses coupling connections were successful within the timeframe of this study., (© 2016 by the American College of Prosthodontists.)

Conometric retention has recently been proposed as an alternative to cement- or screw-retention for fixed restorations. Conometric copings can only compensate for slightly nonparallel placement without interfering with retention. This article describes a method of using digital scanning technology to facilitate computer-guided implant planning when an immediate restoration supported by conical abutments is planned with a guided-welded approach. The procedure involves importing the scan data of the conometric coping and of the definitive cast obtained from the surgical template into the implant planning software. This approach increases the accuracy of computer-guided implant planning and reduces the time needed for the surgery., (Copyright © 2017 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.)

The aim of this study was to analyze the degree of mineralization around nine clinically stable titanium dental implants retrieved after 2 months to 17 years for mechanical complications from five patients. The micromorphology and microchemistry of the interface bone at the coronal and apical sides of the threads were analyzed by environmental scanning electron microscope and energy-dispersive X-ray spectroscopy (EDX) on histologic samples. Mineralization was investigated by atomic calcium-to-nitrogen (Ca/N), phosphorous-to-nitrogen (P/N), and calcium-to-phosphorous (Ca/P) ratio evaluation (statistical analysis by two-way analysis of variance with Student-Newman-Keuls; P < .05). EDX showed higher Ca/N, P/N, and Ca/P values for the bone at the coronal side compared to the apical side of the threads in the long-term (≥ 14 years) samples. The two most significant findings were that (1) the interface bone located at the coronal side of the implant threads was generally more mineralized than the interface bone located at the apical side, and (2) the mineralization of the peri-implant bone at the interface increased over time. A higher degree of mineralization was found at 2 months in an immediately loaded implant when compared to the 2-month submerged unloaded control, likely related to the different remodeling events (coronal vs apical side of the implant threads) due to the direction of the loading forces.

The use of the cone-in-cone connection to support definitive restorations was previously evaluated in cases involving full-acrylic resin or hybrid acrylic-resin composite prostheses. The aim of this study was to evaluate the performance of definitive fixed partial prostheses made with monolithic zirconia and supported by cone-in-cone abutments and integrated implants. Implants were placed into healed sites and fresh extraction sockets. The prostheses were placed in the posterior regions of partially edentulous patients after healing periods of 3 months. A total of 76 patients received fixed monolithic zirconia restorations splinted with cone-in-cone connections to two implants that were followed up yearly for 5 years. At each follow-up visit, peri-implant bone levels and pocket depths were recorded. Esthetic, functional, and biologic United States Public Health Services parameters modified by the World Dental Federation study design were assessed at the last follow-up appointments. The opposing dentition was categorized by type of restoration and supporting structure at the time of placement of the definitive zirconia partial restoration and at the 5-year follow-up. The treatment achieved an 88.2% success rate and a 97.4% survival rate at the 5-year follow-up. None of the prostheses became loose or detached. One fixed prosthesis (0.76%) fractured 41 months after placement. No significant difference involving peri-implant bone and probing levels between the experimental times was found. The results of this research indicated that abutment-prosthesis cone-in-cone connections were successful within the 5-year study period.

Purpose: This study evaluated the retention strength of welding caps for Ankylos standard abutments using a pull-out test., Materials and Methods: Each sample consisted of an implant abutment and its welding cap. The tests were performed with a Zwick Roell testing machine with a 1-kN load cell., Results: The retention strength of the welding caps increased with higher abutment diameters and higher head heights and was comparable or superior to the values reported in the literature for the temporary cements used in implant dentistry., Conclusion: Welding caps provide a reliable connection between an abutment and a fixed prosthesis without the use of cement.

Fatigue behavior of the titanium bars is of utmost importance for the safe and reliable operation of dental implants and prosthetic constructions based on these implants. To date, however, only few data are available on the fatigue strength of dental prostheses made with electric resistance welding and laser welding techniques. This in-vitro study highlighted that although the joints made with the laser welding approach are credited of a superior tensile strength, joints made with electric resistance welding exhibited double the minimum fatigue strength with respect to the joints made with laser welding (120 vs 60 N).

Objectives: The aims of the present cross-sectional study are to evaluate the bone remodeling around Morse-cone implants placed subcrestally 1 year after loading and the prevalence of bone loss >0.5 mm after at least 3 years of loading., Material and Methods: Subjects who underwent a radiographic check in 2013 with implants that had been in function for at least 3 years were considered for inclusion. The study population comprised of 145 subjects with a total of 523 implants. At the moment of insertion, all the implants were placed subcrestally from 1 to 3 mm as clinically measured. Radiographs taken at baseline, that is 1 year after loading (T0), and at the follow-up visit in 2013 (T1) were examined. The distance between the rim of the implant and the marginal bone level at mesial and distal aspects of each implant was determined and the mean bone loss calculated., Results: In the total sample, the mean bone loss occurred between baseline and 2013 examination was 0.42 ± 0.77 mm; at T1 424 implants presented the marginal bone level at the implant rim (78) or above it (346). On the other hand, 99 implants presented the rim above the bone crest. Fifty-one implants that at T1 presented the rim above the bone crest, and that between T0 and T1 had lost at least 0.5 mm, were considered losers: 10 implants lost up to 0.5 mm, 11 lost from 0.6 to 1 mm, 16 lost from 1.1 to 2 mm, and 14 lost more than 2 mm of bone. On a subject basis, 34 subjects (group A) with a total of 200 implant sites presented loser implants, while 111 subjects (group B) with 323 implants displayed non-loser implants., Conclusions: Within the limits of a cross-sectional study, the results show that Morse-cone implants placed subcrestally in the vast majority of cases (89.9%) are able to maintain the bone crest at level of the rim or above it 1 year after loading. The incidence of loser sites (bone loss >0.5 mm) after at least 3 years of follow-up is 9.7% at implant level and 23.5% at patient level., (© 2016 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.)

Inaccuracy of computer-guided implant placement may lead to complications when combined with an immediately loaded prefabricated prosthesis. The aim of this case series was to describe the use of an intraoral welding technique to increase the predictability of immediately loaded implants supporting a fixed full-arch prosthesis after computer-guided flapless implant placement. A total of 60 Ankylos plus implants (Dentsply) with a width of 3.5 mm and a length of 8 to 14 mm were placed consecutively in 10 patients. The implants were functionally loaded using the intraoral welding technique on the day of surgery. The accuracy of guided implant placement was assessed by matching the planning cone beam computed tomography (CBCT) scans with postoperative CBCT scans. No mechanical or biologic complications were registered at the 1-year follow-up. The global coronal deviation of implant placement from the guide plan ranged from 0.25 to 2.84 mm (SD: 0.6 mm), with a mean of 1.28 mm. Average angle deviation was 3.42 degrees (range 0.38-7.82 degrees; SD: 1.52 degrees). The global apical deviation ranged between 0.36 and 3.85 mm (SD: 0.71 mm), with a mean of 1.65 mm. Despite the inaccuracy registered, this guided-welded approach allowed successful achievement of a passive fit of the full-arch prosthesis on the inserted implants the same day of the surgery and provided a high implant and prosthetic survival rate at the 1-year follow-up.

Purpose: The aims of this study were to evaluate the ability of a stepped osteotomy to improve dental implant primary stability in low-density bone sites and to investigate possible correlations between primary stability parameters., Materials and Methods: The study was performed on fresh humid bovine bone classified as type III. The test group consisted of 30 Astra Tech EV implants inserted following the protocol provided by the manufacturer. The first control group consisted of 30 Astra Tech EV implants inserted in sites without the underpreparation of the apical portion. The second control group consisted of 30 Astra Tech TX implants inserted following the protocol provided by the manufacturer. Implant insertion was performed at the predetermined 30 rpm. The insertion torque data were recorded and exported as a curve; using a trapezoidal integration technique, the area underlying the curve was calculated: this area represents the variable torque work (VTW). Peak insertion torque (pIT) and resonance frequency analysis (RFA) were also recorded., Results: A Mann-Whitney test showed that the mean VTW was significantly higher in the test group compared with the first control and second control groups; furthermore, statistical analysis showed that pIT also was significantly higher in the test group compared with the first and second control groups. Analyzing RFA values, only the difference between the test group and second control group showed statistical significance. Pearson correlation analysis showed a very strong positive correlation between pIT and VTW values in all groups; furthermore, it showed a positive correlation between pIT and RFA values and between VTW and RFA values only in the test group., Conclusion: Within the limitations of an in vitro study, the results show that stepped osteotomy can be a viable method to improve implant primary stability in low-density bone sites, and that, when a traditional osteotomy method is performed, RFA presents no correlation with pIT and VTW.

Sinus augmentation procedure has been demonstrated to be a highly predictable treatment in posterior maxilla atrophy. All the surgical interventions in the maxillary region require deep knowledge of anatomy and possible anatomical variations. In this article, pre-operative and post- operative assessments of sinus cavity as well as novel approaches to deepen our knowledge of the behavior of bone substitute materials are described. The awareness of the patient's morphologic conditions enables exact planning of invasive surgery and aids to avoid complications. Pre- operative radiologic evaluation of the region before sinus lift is advisable both for a planning of the sinus augmentation and for selection and alignment of the optimum placement of implants. On the orthopantomography it is possible to measure the vertical dimension of graft, but not the volume and 3D changes. Cone-beam computed tomography (CBCT) has become the "gold standard" to plan a comprehensive implant treatment and to achieve a post-operative assessment. A computer-aided design/computer-aided manufacturing (CAD/CAM) technique is proposed to produce custom-made block grafts for sinus lift procedure, and a customized cutting guide to accurately place the lateral wall and ease membrane elevation. This procedure allows to reduce intervention time, to precisely adapt the scaffold, to reduce risk of complications and to improve operation quality. Recently, a novel approach has been used to deepen our knowledge of the behavior of BSBs: by means of synchrotron micro-tomography (SCT). It is a 3-D analyzing method, suitable to examine the dynamic and spatial arrangement of regenerative phenomena in complex anatomical structures such as bone, where tissues with several morphologies (alveolar process, unmineralized extracellular matrix, regenerated vessels, etc.) compete to achieve the final goal of bone regeneration., (Copyright© Bentham Science Publishers; For any queries, please email at epub@benthamscience.org.)

Various grafts or combination of bone substitute materials have been used in sinus lift procedures. Currently, ongoing developments in several disciplines, from molecular biology and chemistry to computer science and engineering, have contributed to the understanding of biological processes leading to bone healing after the use of bone substitute materials (BSBs) and therefore of the behavior of BSBs. The understanding of the properties of each graft enables individual treatment concepts and therefore allows shift from a simple replacement material to the modern concept of an individually created composite biomaterial. Indeed, the choice of the best BSB still remains crucial for success in maxillary sinus augmentation procedures. The present article provides an overview of most of the materials currently available for sinus lift, with a specific focus on their histological, molecular, cellular and pharmaceutical aspects., (Copyright© Bentham Science Publishers; For any queries, please email at epub@benthamscience.org.)

Purpose: The presence of a microgap between implant and abutment could produce a bacterial reservoir which could interfere with the long-term health of the periimplant tissues. The aim of this article was to evaluate, by x-ray 3-dimensional microtomography, implant-abutment contact surfaces and microgaps at the implant-abutment interface in different types of implant-abutment connections., Materials and Methods: A total of 40 implants were used in this in vitro study. Ten implants presented a screw-retained internal hexagon abutment (group I), 10 had a Morse Cone taper internal connection (group II), 10 another type of Morse Cone taper internal connection (group III), and 10 had a screwed trilobed connection (group IV)., Results: In both types of Morse Cone internal connections, there was no detectable separation at the implant-abutment in the area of the conical connection, and there was an absolute congruity without any microgaps between abutment and implant. No line was visible separating the implant and the abutment. On the contrary, in the screwed abutment implants, numerous gaps and voids were present., Conclusions: The results of this study support the hypothesis that different types of implant-abutment joints are responsible for the observed differences in bacterial penetration.

Over the past decades, the technological development in the medical field, coupled with the ongoing scientific research, has led to the development and improvement of dental prostheses supported by screw-retained metal frameworks. A key point in the manufacture of the framework is the achievement of a passive fit, intended as the capability of an implant-supported reconstruction to transmit minimum strain to implant components as well as to the surrounding bone, when subject to any load. The fitting of four different kinds of screw-retained metal frameworks was tested in this article. They differ both in materials and manufacturing process: two frameworks are made by casting, one framework is made by computer-aided design and computer-aided manufacturing and one framework is made by electric resistance spot welding (WeldONE, DENTSPLY Implants Manufacturing GmbH, Mannheim, Germany). The passivity of the frameworks was evaluated on the entire system, composed of a resin master cast, the implant analogues embedded in the cast and the frameworks. Strains were recorded by means of an electrical strain gauge connected to a control unit for strain gauge measurements. The experimental tests were carried out in the laboratories of the Department of INdustrial engineering at the University of Bologna. The results of the test campaigns, which compared three samples for each technological process, showed that no significant differences exist between the four framework types. In particular, the frameworks made by the resistance welding approach led to a mechanical response that is well comparable to that of the other tested frameworks.

Objective: This study aimed at a histologic and histomorphometric analysis of the periimplant tissues and bone-titanium interface reactions in successfully osseointegrated, clinically stable, and immobile human titanium dental implants retrieved after a long loading period., Materials and Methods: In the last 30 months (2013-2015), 21 implants, retrieved from individuals for different causes after a loading period ranging from 4 to 20 years, were sent to the Implant Retrieval Center, University of Chieti-Pescara, Italy. In 4 cases, almost all the bone had been lost during the retrieval, whereas in the remaining 17 cases, mineralized bone was still present., Results: Around the majority of the implants, mature compact bone with few marrow spaces was found. The trabecular bone, constituted by a few thin bone trabeculae, was in a periimplant location around only a few implants. A high percentage of bone-implant contact (BIC) (comprised between 32 ± 4.1% and 83 ± 2.9%) was present. In almost all implants, the space within the threads was almost completely filled by compact lamellar bone or by a thin layer of bone. Close and tight contact between bone and implant surface was observed in all specimens with no gaps or connective tissue at the interface., Conclusions: All implants appeared to be well integrated in the surrounding mineralized bone, and all of them showed adequate bone-to-implant contact percentages.

Objective: The aim of this prospective cohort study was to assess the ten-year performance of the condensing thread, self-tapping apex and internal hexagonal connection XiVE implant supporting partial fixed prostheses placed with an immediate restoration approach., Material and Methods: All patients received a fixed two- to four-unit partial provisional restoration supported by immediately loaded implants. The final gold alloy/ceramic restorations were cemented approximately 28 weeks after implant insertion. Marginal bone level, pocket probing depth and percentage of bleeding on probing, biological or technical complications and any other adverse events were measured annually up to ten years after surgery. The overall success and survival rates at implant level were evaluated following the International Congress of Oral Implantologists (ICOI) Pisa Consensus Conference criteria. Implant placement in post-extractive or healed sites, smoking and a history of periodontal treatment were evaluated to assess whether they had an influence on bone resorption or on implant survival., Results: Of 114 patients, for a total of 284 implants, fulfilled all the inclusion criteria and were enrolled in the study. 78 (27.5%) implants placed in 30 (26.3%) patients were lost to follow-up. Eight of 284 (2.8%) implants failed in 8 of 114 (7.0%) patients: one (12.5% of losses) due to failure to achieve osseointegration and seven (87.5% of losses) due to peri-implantitis. No cluster implant failures were assessed. The failure of the implant caused the failure of the prosthesis due to the strategic position of the implant in four patients. At the final ten-year follow-up, 121 (61.4%) implants exhibited a "full success" status with an optimal health condition, 21 (10.9%) implants scored a "satisfactory survival" condition, while 49 (25.49%) of the implants were classified as "compromised survival" status (Misch et al. 2008). Smoking was found to be statistically associated with "implant failure" (P = 0.010), while no association was found for patients treated for periodontal disease (P = 0.679) and post-extractive surgical sites (P = 0.664). Statistically significant more marginal bone loss was found in patients treated for periodontal disease (P < 0.0001). An increased bone loss was also observed in smokers, but the difference with the non-smokers was not statistically significant (P = 0.06)., Conclusions: The XiVE implants can be successfully used to support immediate prosthesis. Patients with a history of periodontitis show increased bone loss and risk to develop peri-implant disease. Smoking seems to jeopardize the long-term implant survival., (© 2015 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.)

The aim of this prospective study was to demonstrate the feasibility of the conic coupling connection as a novel approach for the retention of immediately loaded, titanium-reinforced, temporary fixed partial restorations. The patients received a fixed, immediate partial restoration, attached using the conic coupling connection to two implants placed in a fresh extraction socket. Changes in marginal peri-implant bone level or probing depth measurements, biologic or technical complications, and any other adverse event were recorded at yearly follow-ups up to 3 years after implantation. A total of 78 implants placed in 39 patients reached the 3-year follow-up. A trend of bone overgrowth over the implant platform (mean: 0.2 mm) and a complete fill of the vertical gap between the implant platform level and the first point of contact of the bone with the implant surface was seen after the 6-month follow-up. No disconnection of any prosthesis was noted during 3 years of full occlusal function. The results of this study suggest that titanium-reinforced, temporary partial restorations with conic coupling retention supported by immediate implants provide a successful, cost-effective treatment modality.

Purpose: The purpose of this present study was to investigate the relation between implant site underpreparation and primary stability in the presence of poor-quality bone., Materials and Methods: A study was performed on fresh humid bovine bone; samples presented no cortical layer with a cancellous structure inside and were obtained from the hip. The bones were firmly attached to a base device. Sixty sites were prepared according to the protocol provided by the manufacturer: a 2-mm pilot drill was introduced to the proper depth and then twist drills of 3 and 3.4 mm were used. After site preparation, 20 3.4- × 11-mm (standard protocol group), 20 3.8- × 11-mm (10% undersized group), and 20 4.5- × 11-mm (25% undersized group) implants were inserted at a calibrated maximum torque of 70 N-cm at the predetermined speed of 30 rpm. After implant insertion, variable torque work (VTW), maximum insertion torque (peak IT), and resonance frequency analysis (RFA) values were recorded., Results: The standard protocol group showed a mean VTW of 565.77 ± 219.12 N-cm, a peak IT of 11.3 ± 4.44 N-cm, and an RFA of 69.35 ± 7.35 implant stability quotient (ISQ). The 10% undersized group showed a mean VTW of 1,240.24 ± 407.78 N-cm, a peak IT of 20.26 ± 7.03 N-cm, and an RFA of 73.40 ± 2.33 ISQ. The 25% undersized group showed a mean VTW of 1,254.96 ± 727.49 N-cm, a peak IT of 17.15 ± 10.39 N-cm, and an RFA of 72.30 ± 6.70 ISQ. For VTW, the difference between the standard and undersized protocol values was statistically significant; for peak IT, the difference between the standard and 10% undersized protocol values was statistically significant; no other statistical differences were found between mean values., Conclusions: In the presence of poor-bone quality, a 10% undersized protocol is sufficient to improve the primary stability of the implant; additional decreases do not seem to enhance primary stability values., (Copyright © 2015 American Association of Oral and Maxillofacial Surgeons. Published by Elsevier Inc. All rights reserved.)

The electric resistance welding procedure is used to join a titanium bar with specific implant abutments in order to produce a framework directly in the oral cavity of the patient. This investigation studied the effects of the welding process on microstructure and hardness properties of commercially pure (CP2 and CP4) Ti components. Different welding powers and cooling procedures were applied to bars and abutments, normally used to produce the framework, in order to simulate the clinical intraoral welding procedure. The analyses highlighted that the joining process did not induce appreciable changes in the geometry of the abutments. However, because of unavoidable microstructural modifications in the welded zones, the hardness decreased to values lower than those of the unwelded CP2 and CP4 Ti grades, irrespective of the welding environments and parameters., (© IMechE 2015.)

Purpose: The present study aimed to assess clinical and biological performances of several bone substitute biomaterials (BSBs)., Materials and Methods: The evaluation was conducted at 6 months and after several years on 295 patients undergoing sinus augmentation with 13 different BSBs; the data belonging to previously published studies have been analyzed using innovative mathematical models to evaluate the bone regenerative index (Br) and the structural density index (Ds)., Results: After 6 months, compared to the Ds index of native bone, the regenerated bone showed a D3 bone type; while, after several years, the regenerated bone type was D2, with an evident increase in the density of the regenerated bone over time. Moreover, the values of Br were higher for combined biomaterials indicating a fewer amount of residual particles and marrow spaces, while the values of Ds were higher for anorganic bovine bone indicating a greater new bone formation and a lesser amount of marrow spaces. After 20 years, the bone regenerated using hydroxyapatite still had a D4 bone quality., Conclusions: After 6 months of healing, the regenerated bone had a composite structure resembling poor D3 bone type, and covered approximately one-third of the space filled by BSBs. None of the evaluated biomaterials seemed to be ideal., (© 2013 Wiley Periodicals, Inc.)

Purpose: The aim of this trial was to assess if the nonremoval of abutments placed at the time of surgery would improve bone and gingival healing around single immediately restored implants placed in postextraction sockets., Materials and Methods: All patients received a single square-threaded tapered implant placed in postextraction sockets and immediately restored. All the implants were placed 2.0 mm below the bone crest, avoiding any contact with the coronal portion of the buccal wall. Six months after surgery, 35 patients were treated following the control standard prosthetic protocol: the abutments were removed and impressions were made directly on the implant platform. Thirty-three patients underwent the "one abutment at one time" test protocol: impressions were made of the abutments using snap-on abutment copies. The dimensional changes of the soft and hard tissues were assessed using digital photography and cone beam computed tomography radiographs immediately after surgery and at 6-, 12-, and 24-month follow-up examinations., Results: All implants were osseointegrated and clinically stable at the follow-up examinations. No statistically significant difference was evidenced between the two groups regarding the measurement of vertical bone healing. After the placement of the final restoration, a significant horizontal loss in the hard tissue portion over the implant platform was assessed (p = .03 mesial sites; p = .04 distal sites). An 87% increase of the mean recession of the buccal soft tissue was observed in the control group (+0.27 mm) in the same time frame., Conclusions: The nonremoval of abutments placed at the time of the surgery improves the stability of healed soft and hard tissues around the immediately restored, subcrestally placed tapered single maxillary implant., (© 2013 Wiley Periodicals, Inc.)

Purpose: The surface chemical and physical properties of materials used for implants have a major influence on blood clot organization. This study aims to evaluate the blood clot extension (bce) on zirconia and titanium. bce was measured in association to surface roughness (Ra) and static contact angle (θ)., Materials and Methods: Forty disk-shaped samples of sandblasted yttria tetragonal zirconia polycrystal (sb-YTZP), machined titanium (m-Ti), and sandblasted, high-temperature, acid-etched titanium (p-Ti) were used in the present study. About 0.2 mL of human blood, immediately dropped onto the specimen's surface and left in contact for 5 minutes at room temperature, was used to measure the bce. Specimens were observed under confocal scanning laser and scanning electron microscopes., Results: The bce (mean × 10(7)  ± standard deviation [SD] × 10(6)  μm(2) ) was 2.97 ± 6.68 for m-Ti, 5.64 ± 6.83 for p-Ti, and 3.61 ± 7.67 for sb-YTZP. p-Ti samples showed a significantly higher bce. Ra (mean ± SD [μm]) was 0.56 ± 0.7 for m-Ti, 3.78 ± 0.8 for p-Ti, and 2.68 ± 0.6 for sb-YTZP. The difference was not significant between sb-YTZP and p-Ti. θ (mean ± SD) was 55.6 ± 5.6 for m-Ti, 48.7 ± 2.8 for sb-YTZP, and 38.0 ± 2.2 for p-Ti. The difference was not significant between m-Ti and sb-YTZP., Conclusions: The sb-YTZP demonstrated a significantly lesser amount of bce compared with p-Ti specimens, notwithstanding that any significant difference was present between Ra and θ., (© 2013 Wiley Periodicals, Inc.)

Titanium (Ti) is one of the most widely used biomaterials for manufacturing dental implants. The implant surface properties strongly influence osseointegration. The aim of the present study was to in vitro investigate the characteristics of Ti dental implants in terms of mutagenicity, hemocompatibility, biocompatibility, osteoinductivity and biological safety. The Ames test was used to test the mutagenicity of the Ti dental implants, and the hemolysis assay for evaluating their hemocompatibility. Human adipose - derived stem cells (ADSCs) were then seeded onto these implants in order to evaluate their cytotoxicity. Gene expression analyzing with real-time PCR was carried out to investigate the osteoinductivity of the biomaterials. Finally, the genetic stability of the cells cultured onto dental implants was determined by karyotyping. Our results demonstrated that Ti dental implants are not mutagenic, do not cause hemolysis, and are biocompatible. The MTT assay revealed that ADSCs, seeded on Ti dental implants, proliferate up to 30 days in culture. Moreover, ADSCs loaded on Ti dental implants show a substantial expression of some osteoblast specific markers, such as COL1A1, OPN, ALPL, and RUNX2, as well as chromosomal stability after 30 days of culture in a medium without osteogenic factors. In conclusion, the grit-blasted and acid-etched treatment seems to favor the adhesion and proliferation of ADSCs and improve the osteoinductivity of Ti dental implant surfaces.

Background: Differences in implant microtexture are important in conditioning the bone response around dental implants., Purpose: The aim of the present study was an evaluation of the bone response in machined (M), blasted with apatitic calcium phosphate (tricalcium phosphate/hydrossyapatite [HA] blend) particles (resorbable blast texturing [RBT]), and coated with HA implants., Methods: A total of 48 (16 M, 16 RBT, and 16 HA) threaded screw-shaped implants were inserted into the tibia of 12 rabbits. The specimens were retrieved after 1, 2, 4, and 8 weeks and processed for histology., Results: All experimental groups showed an increase of the bone-implant contact percentages through the study period. Higher and highly statistically significant differences were found in the percentages of bone observed in the concavities rather than in the convexities of the implants retrieved after 1, 2, and 4 weeks, while no significant differences were found after 8 weeks. In the different time periods, higher percentages of bone-implant contact were found in the RBT and HA-coated implants both in the concavities and in the convexities, but these differences were not statistically significant., Conclusions: The newly formed bone present in the concavity of the threads was not influenced by the implant surface in the first healing period, while after 4 to 8 weeks, the percentage of bone observed in the concavities and convexities was similar. Additional histological studies are necessary to further evaluate the critical role of the concave geometry in bone differentiation and formation around dental implants., (© 2013 Wiley Periodicals, Inc.)

Angiogenesis plays a key role in bone formation and maintenance. Bone formation has been reported to initiate in the concavities rather than the convexities in a hydroxyapatite substratum and the implant threads of dental implants. The aim of the present study was to evaluate the number of the blood vessels inside the concavities and around the convexities of the threads of implants in a rabbit tibia model. A total of 32 thread-shaped implants blasted with apatitic calcium phosphate (TCP/HA blend) (Resorbable Blast Texturing, RBT) (Maestro, BioHorizons(®), Birmingham, AL, USA) were inserted in 8 rabbits. Each rabbit received 4 implants, 2 in the right and 2 in left tibia. Implants were retrieved after 1, 2, 4, and 8 weeks and treated to obtain thin ground sections. Statistically significant differences were found in the number of vessels that had formed in the concavities rather than the convexities of the implants after 1 (p = 0.000), and 2 weeks (p = 0.000), whilst no significant differences after 4 (p = 0.546) and 8 weeks (p = 0.275) were detected. The present results supported the hypothesis that blood vessel formation was stimulated by the presence of the concavities, which may provide a suitable environment in which mechanical forces, concentrations and gradients of chemotactic molecules and blood clot retention may all drive vascular and bone cell migration.

The loss of the buccal alveolar plate following tooth extraction in the maxillary anterior region is an especially challenging condition for the clinician. Immediate implant placement with a flapless approach has been suggested in order to reduce postextraction bone loss. In the presence of a significant vertical gap in the buccal plate after tooth extraction, most authors still recommend a bone augmentation procedure before implant placement. In these reports, buccal bone plate regeneration was obtained through a flapless approach and immediate postextraction implant placement with a cancellous bone and collagen graft in the buccal gap.

The long-term high percentages of survival and success of dental implants reported in the literature are related mainly to new, innovative implant and thread designs, and new implant surfaces that allow to obtain very good primary and secondary stability in most anatomical and clinical situations, even in low quality and quantity of bone, promoting a more rapid osseointegration. The aim of this retrospective study was a histological and histomorphometrical evaluation of the bone response around implants with a parallel-wall configuration, condensing thread macrodesign, and self-tapping apex, retrieved from man for different causes. A total of 10 implants were reported in the present study, and these implants had been retrieved after a loading period comprised between a few weeks to about 8 years. Mineralized newly formed bone was found at the interface of all the implants, in direct contact with the implant surface, with no gaps or connective fibrous tissue. This bone adapted very well to the microirregularities of the implant surface. Areas of bone remodeling were present in some regions of the interface, with many reversal lines. High bone-implant contact percentages were found. In conclusion, both the macrostructure and the microstructure of this specific type of implant could be very helpful in the long-term high survival and success implant percentages.