Search

In the context of global warming associated with the excess of energy consumption, energy saving and environmental sustainability in buildings have become significant issues at both national and European levels. Therefore, the adoption of energy-efficiency measures in new and renovated dwellings will increase the demand for thermal insulation, which is crucial to improve the housing comfort by reducing the heat loss through the building envelope. Over the past two decades, several bio-based materials have been used in building thermal insulation, such as hemp concrete. Promoting the use of hemp concrete in new constructions and restoration of existing buildings first requires a validation of its hygrothermal behavior at both wall and building scales. For this, several models dealing with various physical aspects of hemp concrete were developed to understand their impact on the prediction of changes in temperature and relative humidity. These physical phenomena include hemp concrete hygroscopic hysteresis and thermal dependency of sorption curves. The preliminary results show that hysteresis has a significant influence on the numerical prediction in the short-term, while temperature dependency has less influence at the wall scale. The next part of this article is devoted to the study of these phenomena at the room scale by monitoring the internal conditions and energy consumption of a virtual hemp concrete office. The results highlight the fact that hysteresis and thermal dependency have low impact on indoor conditions, which could probably be related to the other parameters at the room scale. [ABSTRACT FROM AUTHOR]

The paper aims to present a new insulating material based on cork aggregates and cement designed for building applications. Samples are prepared by mixing natural cork aggregates, sand, cement and water. Four cork volume dosages are considered, 0, 25, 50 and 75% (relative to the sand). Samples are characterised in terms of hardened density, compressive and flexural strength, as well as thermal conductivity and hydric properties (moisture content, vapour permeability, moisture buffering value and absorption by partial immersion). Results show that increasing cork granule amount tends to increase moisture retention and buffering value but decreases density, thermal conductivity and mechanical properties. Depending on the cork content, cork concrete mixture can be used as thermal insulator or as a structural component. [ABSTRACT FROM AUTHOR]

Highlights • This study shows the mechanical performance of the beet pulp composite materials. • The binding strength of the beet pulp composite depends on the material density. • The beet pulp composite shows a good thermal and acoustical properties. • The beet pulp material is classified as an excellent hygric regulator. Abstract This work deals with the making of a new renewable green material for building insulation from sugar beet pulp and potato starch. The material is both lightweight and ecofriendly. The influence of starch/extruded sugar beet pulp mass ratio (S/EBP) is studied. Four mass ratios are considered, 10, 20, 30 and 40% (relative to the starch). Samples are characterized in terms of absolute and bulk density, sound absorption coefficient, compressive and flexural strength, as well as and hygrothermal properties (the moisture buffering value and thermal conductivity). The sound absorption coefficient shows that this material is a good sound absorber, especially in medium and high frequencies. The sound absorption capacity depends on the fiber content and the humidity content. The best values are between 0.6 and 0.8. The compressive strength increases linearly with the S/EBP weight ratio to reach 0.52 MPa and the compressive strain is 30%. The elasticity modulus and the Poisson's ratios were also studied. The transversal and vertical strain were measured using ARAMIS optical system. The moisture buffering value was measured according to Nordtest Protocol. The recorded moisture buffering value was between 2.6 and 2.8 g/(%RH.m2) and shows that the sugar beet pulp-starch composite is an excellent hygric regulator. The thermal conductivity is to around 0.070 W/(m·K). The results obtained shows that increasing starch amount tends to decrease composite porosity but increases thermal conductivity and mechanical properties. Depending on the starch content, beet pulp composites have a good thermal and acoustical performance and can be used as building materials. [ABSTRACT FROM AUTHOR]

This article deals with the influence of both morphology and amount of Typha on hygrothermal behavior of a Typha–clay composite for building application. An agromaterial containing the fiber mix of Typha Australis and clay was made in three samples: three fiber mixtures were prepared with different amounts Typha and cut type (transversal or longitudinal). The physical properties of these materials were studied in terms of porosity, apparent and absolute density, thermal conductivity, and hygric properties. Results show a real impact of the Typha fraction type and its volume content on hygrothermal properties of the studied material due to the porosity. The transversal fraction of Typha (80% in volume weight) seems to be the optimal composition for a better hygrothermal behavior. [ABSTRACT FROM AUTHOR]

Global environmental issues are arising over the developed and developing world. Improving energy efficiency and reducing Green Gases emissions become the key issues in all the economic sectors and, in particular, the building sector that is one of the most energy-consuming. It is, therefore, important to find alternative building materials with low-environmental impact contributing to global sustainability. In that context, this study reports on the performance of sustainable materials produced from natural resources as hemp-concrete or from recycled-waste nonbiodegradable materials including recycled polyethylene terephthalate. Three façades employing three different materials (hemp-concrete, hemp-concrete with brick and recycled polyethylene terephthalate) were investigated in three cities in France (Nancy and Carpentras) and Italy (Perugia) with different climate. The energy performance of each façade was assessed in terms of cooling and heating demands, electrical consumption for a constant flow rate ventilation mode, considering different orientations. The study also shows the effect of window size (10%, 25%, and 40%) on the annual energy consumption. [ABSTRACT FROM AUTHOR]

Energy efficiency and the reduction of greenhouse gas emissions are actual key issues in all the economic sectors and, in particular, in buildings which is acknowledged worldwide as one of the most energy-consuming. In this context, it would be desirable to duly address those issues by searching for and assessing proper solutions and strategies: the usage of eco-friendly construction materials can be considered as one of those. This paper reports upon the performance of three façades containing sustainable products that are manufactured using natural resources and, alternatively, post-consumer waste based materials; those are: hemp-concrete; and Recycled PolyEthylene Terephthalate (R-PET), respectively. The energy performance of each façade was assessed in terms of cooling and heating demands, electrical consumptions and indoor thermal comfort including indoor temperature and relative humidity. Additionally, a Carbon Footprint (CF) assessment was carried out considering both the estimated energy demands and the life-cycle emission factors associated with the energy mix of the countries where the façades were located, i.e. France and Italy. Based upon the findings of the study, the R-PET façade represented the most performing solution between the three façades in all the scenarios considered and, moreover, the humidity-sensitive flow rate ventilation system came out as a solution able to reduce the electricity consumptions. Finally, considering the Carbon Footprint results, the energy country mix emerged as a key issue, making the Italian case study the worst one, though the total electrical energy consumption were comparable with those of the other case studies. [ABSTRACT FROM AUTHOR]

This article describes the results of a research project carried out at the University of Reims Champagne-Ardenne. The aim of this article is to develop a new insulating material produced by bonding hemp shives with wheat starch as a binder and to characterize its physical properties such as sorption isotherm, water vapour permeability, thermal conductivity, heat capacity and porosity. The equations of coupled heat and moisture transfer within the panels are introduced. These governing equations are applied on the room level in order to assess the hygrothermal behaviour of the panels and its impact on energy consumption and indoor comfort. Simulations are performed for Nancy (France) winter conditions with the simulation environment Simulation Problem Analysis and Research Kernel (SPARK) suited for complex problems. [ABSTRACT FROM AUTHOR]

Following the environnement grenelle, reaching 10% of bio-resourced materials in building sector except wood is one of goals until 2020. Among these agro-materials, one can distinguish the hemp concrete. Based on hemp hurds and mineral binders including lime or polymer as starch, the hemp composites are appreciated for their hydrothermal and acoustic properties. In this study, a vegetal binder based on starch and extracted from wheat is used with treated and non-treated hemp hurds to form an ecological composite. The studied hemp-starch is prepared with a ratio (H/S = 3,3). Hygrothermal properties such as moisture buffering value, sorption isotherm, water vapor permeability, thermal conductivity, and heat capacity are experimentally studied. The pore size distribution is performed using mercury porosimetry. Results reveal that the hemp-starch composite may be a promising solution in the insulation field due to its relatively low thermal conductivity and capacity to regulate the indoor relative humidity. [ABSTRACT FROM AUTHOR]

This paper presents the results of a laboratory investigation into the hygric properties and moisture buffering performance of hemp-starch composite panels designed for building applications. Composite panels were produced by bonding hemp shiv with wheat starch as a binder. Two types of hemp shiv were tested: chemically processed shiv with enhanced adhesion between fibers and starch matrix, and non-treated shiv. The panels were then characterised in terms of their hygroscopic properties (sorption curve and vapour diffusion resistance factor) and their moisture buffering performance (moisture buffering value, MBV). The determination of theoretical MBV was based on the effusivity of the material, which is obtained from its basic hygroscopic characterisation. The results show that both panels are excellent hydric regulators that can be used to improve indoor hygrothermal comfort by buffering indoor relative humidity variations. [ABSTRACT FROM AUTHOR]

The gradual development of government policies for ecological transition in the modern construction sector leads researchers to explore new alternative and low environmental impact materials with a particular focus on bio-sourced materials. In this perspective, the mechanical, thermal insulation, and the sound absorption performances of a spent coffee grounds/potato starch bio-based composite were analyzed for potential application in buildings. Based on thermal conductivity and diffusivity tests, the coffee grounds waste biocomposite was characterized as an insulating material comparable with conventional thermal insulation materials of plant origin. Acoustical tests revealed absorption coefficients in the same range as other conventional materials used in building acoustical comfort. This bio-sourced material presented a sufficient compressive mechanical behavior for non-load-bearing structures and a sufficient mechanical capacity to be shaped into building bricks. Mechanical, thermal, and acoustic performances depend on the moisture environment. The groundwork was laid for an initial reflection on how this composite would behave in two opposite climates: the continental climate of Reims in France and the tropical climate of Belém in Brazil. [ABSTRACT FROM AUTHOR]

[Display omitted] • This study presents a state-of-the-art on thermal bridges focusing on slab on grade TB, including calculation methods, norms and software summary. • A numerical study of possible technical solutions to decrease slab on grade TB's effect is presented. • Different external insulation solutions to renovate existing building were compared. • The study highlights the effect of soil thermal properties on slab on grade TB calculation. • Improving insulation thickness and depth does not necessarily reduce the thermal bridges effect. The building industry is responsible for considerable energy consumption and the production of large amounts of greenhouse gas emissions worldwide. Hence, reducing the building heat losses that occur through the building envelope, especially through the floor foundations, is important. This paper provides an up-to-date review on thermal bridges (TBs), mainly with respect to slab-on-grade TBs. First, different thermal bridges types are defined; then the standards used to evaluate TBs are presented. Common approaches to evaluate TBs are discussed, such as the U-value method, the equivalent method approach, and the three-dimensional dynamic method. This latter focuses on heat loss through the foundation and soil in existing buildings. Soil's effect on thermal bridges is described and our case studies showed that thermal bridges heat losses are inversely proportional to soil thermal conductivity. This analysis is involved in the present paper. Finally, exterior insulation solutions at ground level are presented among those the trapezoidal double insulation type can reduce TBs up to 65% compared to no insulation case. As conclusions, directions for further works are suggested to fill current literature gaps. [ABSTRACT FROM AUTHOR]

One possible approach to reducing the environmental impacts associated with the building sector is the development and use of bio-based building materials. The objective of this study is to determine the water properties of bio-based insulation materials, derived from winegrowing co-products, which promote energy efficiency. The water performance of these new bio-based materials is based on the measurement of the moisture buffer value, the sorption isotherm, and the water vapor permeability. Four by-products are analyzed: stalks, grape pomace, crushed stalks, and skins; they are combined with a potato starch binder. The performance of these composites is compared to two other bio-based composites (hemp/starch and beet pulp/starch). The stalk/starch composite can be classified as a hygroscopic and breathable material with excellent moisture retention capacity. [ABSTRACT FROM AUTHOR]

Raw earth bricks made from the soil of the Chalky Champagne region (France) have been used for at least two millennia in construction, a promising heritage in the context of reducing the carbon emissions of buildings. The present experimental study aims to measure the physical, mechanical, thermal, and hydric properties of adobes collected from a local village barn. The results show a high chalk content, estimated at 71%, and a clay content, acting as a binder, of 14%. Despite limited load-bearing capacity, these lightweight adobes are suitable for current single-story constructions, while their hydrothermal properties classify them as excellent moisture regulators for occupants. In association with other bio-sourced materials such as starch–beet pulp bricks, Chalky Champagne adobes yield promising insulating properties, and meet the criteria defined by current energy standards. [ABSTRACT FROM AUTHOR]

This article deals with the elaboration and the characterization of an innovative 100% plant-based green composite made solely of beet pulp (BP) and potato starch (S). Using this type of material in insulation applications seems a good solution to reduce the CO2 gas emissions in building. The influence of the starch amount on composite characteristics was studied. Four mixtures were considered with different S/BP mass ratios (0.1, 0.2, 0.3 and 0.4). The physical properties of these materials were studied in terms of porosity, apparent and absolute densities, thermal conductivity, and hygric properties. The influence of humidity content on acoustical properties was studied as a function of frequency. Test results show a real impact of both starch and humidity contents on the hygrothermal and acoustical properties of the studied material due to the porosity. The composite with the lowest amount of starch (S/BP = 0.1) seems to be the optimal composition in terms of the hygrothermal and acoustical behaviors. [ABSTRACT FROM AUTHOR]

Solar radiation is a renewable non polluting energy source which can be used in buildings through various systems technologies. Thermal radiation, absorbed or transmitted by the walls and windows, creates a solar gain which has a direct impact on the thermal behavior in the building. Most existing thermal models neglect the effect of the evolution of the sun patch position on the heating floor which can have a great impact on the indoor thermal comfort. In this paper, we present numerical model to calculate the transient sun patch position and its influence on the heating floor model in order to evaluate its impact on the heating floor operating conditions and on the indoor air temperature, which has a great influence on thermal comfort under the climatic conditions of Oran city in Algeria. The sun patch is calculated using Ray Tracing model as proposed in FLUENT whereas the room and the heating floor are modelled with TRNSYS software. Using literature data, the two proposed models (sun patch model and heating floor model) are validated and used to simulate the cases with different geographic locations and different window orientations, surfaces, and positions. Our results suggest that the displacement of the sun patch on the heating floor lead to a superheating of the irradiated zone and it affects the indoor air temperature and thermal comfort too. [ABSTRACT FROM AUTHOR]

Low impregnation of the fiber when the fiber ratio is high may therefore be responsible for the loss of mechanical properties, but it is not the only reason for Nettle and also for kenaf fibers (a variety of hemp) (Kumar and Das [73]). Vegetal fibers; Nettle fiber Nettle fiber culture Nettle plants are very common under our latitudes. Other fibers treatment used for Nettle fibers in a PLA/Nettle composite The study reported by Yu, Jiang, and Li ([120]) uses two different concentrations of maleic anhydride (MA) to create a Ramie/PLA composite. Keywords: Stinging nettle; polylactic acid; mechanical characteristics; biodegradable; treatment; automotive; : ; ; ; ; ; EN Stinging nettle polylactic acid mechanical characteristics biodegradable treatment automotive ZH : 8205 8229 25 11/21/22 20221220 NES 221220 Introduction Nettle and Ramie both belong to the Urticaceae family, but they are from different genus, (Hassler [54]). Fibers caracteristics according to mechanical properties (Gourier [52]) HT

• This paper explores the effect of embedding PCM in sugar-beet-pulp/starch bricks. • Experimental measurements and 3D heat transfer simulations were done. • The 3D heat transfer simulations closely follow the experimental measurements. • The embedded PCM leads to increased thermal inertia of the bricks. • This effect is only practically relevant for walls made of one layer of bricks. Due to environmental concerns, bio-based materials are being increasingly investigated and used in buildings. In general, the density of these materials, and thus their thermal inertia, is low. Thermal inertia can be beneficial for reducing the energy use of buildings by damping indoor temperature fluctuations or by reducing and delaying incoming (solar) heat through the façade. This study explores the thermal inertia of regular-sized bricks made of a sugar-beet-pulp/starch mixture (BP/S), and with 17 circular holes inside. The holes were filled either with the BP/S mixture, with air, with a stabilised phase change material (PCM) gel or with a salt-hydrate based PCM. The brick was insulated on all sides but one. Two series of experimental measurements were performed: 1.) a heating film placed at the back (insulated) side of the brick heated the brick until steady-state conditions were reached; 2.) the heated brick was then passively cooled down to ambient temperature by cutting the power to the heating film. Numerical simulations of these experimental measurements were also modelled using the COMSOL Multiphysics® software. In addition, simulations were run to study the thermal inertia of a full brick wall made out of 1 layer and of 4 layers of the BP/S brick with and without PCM, exposed to a combination of a sinusoidal outdoor air temperature fluctuation with an imposed radiation flux on the outdoor surface, representing summer conditions. The results show that the brick in which the holes were filled with phase change material had a slower temperature response and thus higher thermal inertia than the bricks in which the holes were filled with BP/S or with air. The salt-hydrate based PCM with the higher latent heat of fusion led to the slowest temperature response and highest thermal inertia. Furthermore, the calculated simulations could accurately reproduce the experimental measurements. Applying PCM in thick walls (40 cm) made of BP/S bricks however hardly affects the temperature amplitude damping and time delay of the complete wall. The addition of PCM therefore is only effective for thinner walls (10 cm). [ABSTRACT FROM AUTHOR]

This paper presents a study on energy performance of an earth air heat exchanger (EAHE) for buildings in Maghreb climatic context (Oran, Bechar and Adrar cities in Algeria). In order to check the influence of the material, two air conducts (one of galvanized sheet metal and the other in polyvinyl chloride–PVC) are considered under the same geometric conditions (a 20 m conduct length, 120 mm diameter and 2 m burial depth). They are used separately for the ventilation in simple current flow of two adjoining rooms constituting a test cell located at the university campus IGCMO-USTOMB (Oran, Algeria). An experimental device has been set up to measure the temperature at different points (air inlet/outlet air duct). Measurements were run in August 2015, and the monitoring of both exchangers allowed us to evaluate their cooling performance: 35.41% for the Zinc pipe and 58.42% for the PVC pipe. Experimental results were compared to those obtained from the simulation (under the Trnsys 16) and a fair similarity is obtained. In order to optimize the energy performance of the exchanger (EAHE), numerical simulations are carried out by varying different parameters: climate, burial depth, length and diameter of the duct. Other simulations have shown that the energy supplied by the cooling exchanger (EAHE) is more significant in the south of the country (Adrar and Bechar) than in the north (Oran). [ABSTRACT FROM AUTHOR]

Hemp shives is a lightweight material known for its insulating properties. Associating these bio-fibers with plant-based matrix instead of a mineral binder in insulation applications is of ecological interest. This article describes the study of a low environmental impact 100% plant-based material made solely from wheat starch and hemp shives. The hemp/starch ratio (H/S) influence and hemp shive size are studied. Samples are evaluated in terms of physical properties, mechanical behaviour and hygrothermal properties through an experimental approach. Results show that increasing 0–5 mm hemp shive proportion from 15% to 30% leads to a significant enhancement of the mechanical and hygric characteristics due to the load transfer and porosity. However, when the H/S ratio increases, mechanical and hygrothermal characteristics decrease slightly. Finally, the hemp-starch agro-material with H/S equal to 8 and 30% of 0–5 mm hemp shive seems to be the optimal composition between the studied samples. [ABSTRACT FROM AUTHOR]

• Two types of beet-pulp/starch bricks are investigated: full and hollowed bricks. • The preparation of the mixture and bricks manufacturing are described in details. • The microstructure of the mixture constituents are described and analyzed. • The drying kinetics of the bricks are compared and predicted via mathematical models. • The mechanical behavior of the bricks is studied via compressive tests on each type. Buildings account for a large share of the primary energy and materials use in Europe. Therefore, the EU has set several energy and materials targets for the built environment and other sectors. Novel low-carbon materials can play a major role in the transition towards meeting those targets. Moreover, agriculture produces by- or waste products that could be used as constituent of innovative agro-materials for construction. Recently, beet pulp based-material is being investigated on the material scale and promising results are pointed out regarding its interesting mechanical, hygrothermal and acoustical properties for building insulation use. In this context, the paper aims to study experimentally two types of beet-pulp starch composites: whole bricks and hollowed bricks. The manufacturing of the two types of bricks is detailed. A comparative study is then achieved regarding the drying kinetics, mechanical properties as well as internal structure composition. [ABSTRACT FROM AUTHOR]

This article concerns the elaboration and the characterization of a novel biobased potato starch-beet pulp composite for packaging applications as cushion foams. A twin-screw extruder was used to elaborate composite foams. SEM observations of these materials were conducted, and thermomechanical properties were studied in terms of thermal transitions (TGA, DSC) and viscoelastic properties (DMA). The effect of relative humidity content on viscoelastic properties was analyzed as a function of frequency. The different test results show that the composite structures are homogeneously mixed. The sponge-like structure of the beet-pulp disappears indicating a good compatibility between the two mixed constituents. The DSC curve of starch-beet pulp foam shows a single thermal transition at 153.6 °C, indicating the thermal homogeneity of the obtained composite material. The density value of starch-beet pulp foam is higher than conventional foams, but this can be optimized by adjusting the technological parameters of the extruder. The viscoelastic properties of the developed materials depend on the relative humidity. [ABSTRACT FROM AUTHOR]