Search

This study aims to evaluate the fatigue resistance of monolithic zirconia (Yz) and multilayer ceramic structures using the CAD-on technique in different thicknesses. Fifty (N=50) standardized single crowns preparations were made in fiberglass-reinforced epoxy resin (NEMA grade G10), digitalized, and restorations were machined in CAD-CAM, composing 5 groups (n= 10): Control: 1.5 mm (milled zirconia framework + manual layered porcelain); Yz monolithic 1.5 mm; Yz monolithic 1.0 mm; CAD-on 1.5 mm; and CAD-on 1.0 mm (milled zirconia framework 0.5 mm thickness bonded by a low fuse ceramic to a milled lithium disilicate layer of 1.0 mm or 0.5 mm, respectively). The G10 bases were conditioned with 10% hydrofluoric acid; the crowns were air abraded with 110 μm alumina particles; and then luted onto each other with self-adhesive resin cement. A cyclic fatigue test was performed (initial load: 400N for 10,000 cycles, frequency of 20 Hz, step size of 200N) until failure, and the data was submitted to a survival statistical analysis. No failures were observed at Yz monolithic 1.5 mm. High and similar performance was observed for Cad-On groups and Yz monolithic 1.0 mm. The control group depicted the worst behavior. The Weibull modulus of CAD-on 1.5 mm was higher than the control while being similar to the other conditions. Both the monolithic systems and the CAD-on technique showed high and similar fatigue fracture behavior and survival rates, which were also higher than the control bilayer system. Both systems reduced the occurrence of delamination failures, making them suitable for clinical use.

The aim of this study was to evaluate the fatigue behavior of strength-graded zirconia polycrystals used as monolithic three-unit implant-supported prosthesis; complementarily, crystalline phase and micromorphology were also assessed. Fixed prostheses with 3 elements supported by 2 implants were confectioned, as follows: Group 3Y/5Y - monolithic structures of a graded 3Y-TZP/5Y-TZP zirconia (IPS e.max® ZirCAD PRIME); Group 4Y/5Y - monolithic structures of a graded 4Y-TZP/5Y-TZP zirconia (IPS e.max® ZirCAD MT Multi); Group Bilayer - framework of a 3Y-TZP zirconia (Zenostar T) veneered with porcelain (IPS e.max Ceram). The samples were tested for fatigue performance with step-stress analysis. The fatigue failure load (FFL), the number of cycles required until failure (CFF), and the survival rates in each cycle were recorded. The Weibull module was calculated and the fractography analyzed. The crystalline structural content via Micro-Raman spectroscopy and the crystalline grain size via Scanning Electron microscopy were also assessed for graded structures. Group 3Y/5Y showed the highest FFL, CFF, probability of survival, and reliability (based on Weibull modulus). Group 4Y/5Y showed significantly superior FFL and probability of survival than group bilayer. Fractographic analysis revealed catastrophic flaws in the monolithic structure and cohesive fracture of porcelain in bilayer prostheses, all originating from the occlusal contact point. The graded zirconia presented small grain size (≤0.61 μm), with the smallest values at the cervical region. The main composition of graded zirconia was of grains at tetragonal phase. The strength-graded monolithic zirconia, especially the 3Y-TZP/5Y-TZP, showed to be promising for use as monolithic three-unit implant-supported prosthesis., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2023 Elsevier Ltd. All rights reserved.)

Intersex children in Brazil are still subjected to "normalizing" surgical procedures and subsequent bodily interventions to make their bodies conform to binary views of sex. Resolution n. 1,664/2003 of the Brazilian Federal Council of Medicine legitimizes interventions upon intersex bodies, being the only national normative instrument that address the subject. However, the demands of international intersex political activism have denounced how early childhood interventions for sex designation mutilate children's bodies and violate a number of human rights. This research discusses how early, irreversible, and normalizing procedures performed without the intersex person's consent are human rights violations. Based on the concept of epistemic (in)justice, we first look at the disputes surrounding the evidence that underpin medical practices. We demonstrate how such procedures violate human rights to health, body integrity, autonomy, and sexual and reproductive rights, analyzing which strategies were put into place to prevent them. We propose that intersex people be at the center of decisions regarding their bodies, that non-surgical paths be discussed with patients and their family members, and that early, invasive, mutilating, harmful, cosmetic, and unconsented surgical interventions on intersex children be prohibited. Guiding tools must introduce changes into its regulatory bias to, from an interdisciplinary perspective, include bioethical and human rights bodies, as well as intersex activists.

Objective: This study aims to evaluate the impact of morning-evening preference in pregnancy outcomes in gestational diabetes mellitus (GDM)., Methods: This is a prospective cohort study of 2nd-3rd trimester GDM outpatient care in Fortaleza, Brazil (2018-2020). Eveningness was defined by the Horne-Östberg Morningness-Eveningness-Questionnaire (MEQ ≤ 41). Furthermore, we obtained a 7-day actigraphic register. Subjective sleep quality, daytime somnolence, insomnia, fatigue and depressive symptoms were also evaluated. Associations with pregnancy outcomes were investigated., Results: Among 305 patients with GDM, evening preference was found in 21 (6.9%). Patients with evening preference had worse sleep quality (p < 0.01), greater severity of insomnia (p < 0.005), fatigue (p < 0.005) and depressive symptoms (<0.009). Evening chronotype was associated with preeclampsia [p = 0.01; OR = 0.27; CI 0.09-0.79] and a greater need for admission to a neonatal intensive care unit (NICU) [p = 0.02; OR = 0.23; CI .0.06-0.80]. A lower MEQ score confirmed an association with preeclampsia [p = 0.002; OR = 0.94; CI 0.90-0.97] and this was maintained after controlling for age, arterial hypertension, sleep quality, fatigue and depressive symptoms [p < 005; OR = 0.91; CI 0.87-0.95]., Conclusion: In GDM, patients with evening preference had worse sleep quality, more insomnia, fatigue, and depressive symptoms. Furthermore, eveningness was independently associated with preeclampsia. These results indicate the important role of eveningness in adverse pregnancy outcomes.

Statement of Problem: Zirconia has been reported to be suitable for multiunit monolithic restorations. However, as the connector region is the weakest part of the system, studies are needed to determine the optimal connector geometry., Purpose: The purpose of this in vitro study was to evaluate the load-bearing capacity under fatigue of implant-supported fixed partial prostheses made of monolithic zirconia with different connector cross-sectional geometries., Material and Methods: Three-unit monolithic fixed partial prostheses (from mandibular second premolar to the second molar) were fabricated in zirconia (Zenostar T) by computer-aided design and computer-aided manufacture (CAD-CAM). Different connector cross-sectional geometries, with an area of 9 mm 2 , were tested (n=10): round, square with rounded angles, or trapezoid with rounded angles. The prostheses were screwed over 2 implants and inserted into acrylic resin bases. The specimens were submitted to a mechanical fatigue test until failure, with load applied to the pontic using the stepwise stress methodology (initial load of 100 N for 5000 cycles, followed by an increase to 200 N for 20 000 cycles, with a subsequent increase of 50 N each step). For data analysis, fatigue failure load (FFL) and cycles for fatigue failure (CFF) were recorded. Failed structures were analyzed by fractography. The Kaplan-Meier test followed by a log-rank Mantel-Cox post hoc test was used to analyze FFL and CFF (α=.05). Weibull analysis was also performed., Results: The round (1065 N) and trapezoid (1010 N) groups presented higher FFL values than the square one (870 N) (P≤.05). For CFF, the round connector (358 777) was better than the square (280 310) (P=.006), and the trapezoid (337 773) was statistically similar to both (P>.05). No difference among groups was observed in Weibull modulus either for CFF or FFL data. All failures were catastrophic, originating at the base of the connector and propagating toward the occlusal surface of the pontic (region under loading)., Conclusions: The connector cross-sectional geometry significantly influenced the mechanical fatigue performance of implant-supported fixed partial prostheses made of monolithic zirconia., (Copyright © 2022 Editorial Council for The Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.)

Background: Robotic surgery is a valid option for minimally invasive surgery in most surgical specialties. However, the need to master laparoscopy is questionable before starting specific training in robotic surgery. We compared the development of basic robotic surgery skills between individuals randomized to train in conventional, laparoscopic, or robotic skills., Methods: We conducted a single-centered, single-blinded randomized trial. Medical students were randomly assigned to 20 h of conventional, laparoscopic, or robotic surgical training. Students with previous surgical experience were excluded. Participants were evaluated pre- and post-training on the dV-Trainer robotic surgical simulator with the following exercises: Camera Targeting 1, Peg Board 1, Ring and Rail 1, and Ring and Rail 2., Results: Sixty-six students were randomly assigned to each training group. Eight individuals did not complete the study (2 in the conventional group, 3 in the laparoscopic group, and 3 in the robotic group). All groups demonstrated significant improvement in the composite score and in each task following the training period (p &lt; 0.001). No differences were seen between the conventional and laparoscopic groups in the composite score or individual tasks. The robotic group showed greater improvement in number of errors, economy of motion, workspace utilization, and time for completion compared to the other groups. The laparoscopic group showed improved camera manipulation skills compared to the conventional group, while the conventional group showed improved errors and economy of motion compared to the laparoscopic group., Conclusion: There was no difference in the acquisition of basic robotic surgical skills between individuals trained in basic conventional or laparoscopic surgical skills. We believe surgeons mastery in laparoscopy is not needed before initiating robotic surgical training. However, basic principles of laparoscopy remain applicable to robotic surgery. Future studies should compare transferability of conventional and laparoscopic training to robotic skills in the operating room., (© 2022. The Author(s), under exclusive licence to Springer Science+Business Media, LLC, part of Springer Nature.)

Background: although preservation of bowel continuity is a major goal in rectal cancer surgery, a colorectal anastomosis may be considered an unacceptably high-risk procedure, particularly for patients with multiple comorbidities. We aimed to assess rates of surgical complications in rectal cancer patients according to the type of procedure they had undergone., Materials and Methods: this cohort included all rectal cancer patients undergoing elective resection at a referral academic hospital over 16 years. There were three study groups according to the type of performed operation: (1) rectal resection with anastomosis without defunctioning stoma (DS); (2) rectal resection with anastomosis and DS; and (3) Hartmann's procedure (HP). Postoperative complications and clinical outcomes were assessed., Results: four-hundred and two patients were studied. The 118 patients in group 3 were significantly older (>10 years), had higher Charlson Comorbidity Index scores, and more ASA class ≥3 than patients in the other two groups. Sixty-seven patients (16.7%) had Clavien-Dindo complications grade ≥ III, corresponding to an incidence of 11.8%, 20.9%, and 14.4% in groups 1, 2, and 3, respectively (p=0.10). Twenty-nine patients (7.2%) had major septic complications that required reoperation, with an incidence of 10.8%, 8.2% and 2.5% in groups 1, 2 and 3, respectively (p=0.048). Twenty-one percent of the group 2 patients did not undergo the stoma closure after a 24-month follow-up., Conclusion: HP was associated with a lower incidence of reoperation due to intra-abdominal septic complications. This procedure remains an option for patients in whom serious surgical complications are anticipated.

This study evaluated the effect of distinct surface treatments on the fatigue behavior (biaxial flexural fatigue testing) and surface characteristics (topography and roughness) of a 5% mol yttria partially stabilized zirconia ceramic (5Y-PSZ). Disc-shaped specimens of 5Y-PSZ (IPS e.max ZirCAD MT Multi) were manufactured (ISO 6872-2015) and allocated into six groups (n = 15) considering the following surface treatments: Ctrl - no-treatment; GLZ - low-fusing porcelain glaze application; SNF - 5 nm SiO 2 nanofilm; AlOx - aluminum oxide particle air-abrasion; SiC - silica-coated aluminum oxide particles (silica-coating); and 7%Si - 7% silica-coated aluminum oxide particles (silica-coating). The biaxial flexural fatigue tests were performed by the step-stress method (20Hz for 10,000 cycles) with a step increment of 50N starting at 100N and proceeding until failure detection. The samples were tested with the treated surface facing down (tensile stress side). Topography, fractography, roughness, and phase content assessments of treated specimens were performed. GLZ group presented the highest fatigue behavior, while AlOx presented the lowest performance, and was only similar to SiC and 7%Si. Ctrl and SNF presented intermediary fatigue behavior, and were also similar to SiC and 7%Si. GLZ promoted a rougher surface, Ctrl and SNF had the lowest roughness, while the air-abrasion groups presented intermediary roughness. No m-phase content was detected (only t and c phases were detected). In conclusion, the application of a thin-layer of low-fusing porcelain glaze, the deposition of silica nanofilms and the air-abrasion with silica-coated alumina particles had no detrimental effect on the fatigue behavior of the 5Y-PSZ, while the air-abrasion with alumina particles damaged the fatigue outcomes., (Copyright © 2021 Elsevier Ltd. All rights reserved.)

Purpose: This study evaluated the influence of different surface treatments of zirconia used to enhance bonding with veneering porcelain, and thermocycling on the resistance to porcelain cracking and delamination during fatigue test., Methods: Bilayer ceramic discs were made from zirconia blocks (IPS e.max Zircad MO, Ivoclar Vivadent - 0.7 mm thickness) and randomized into 8 groups (n= 15) according to two factors: 'zirconia surface treatment' (Control; Grinding - diamond bur; Air-abrasion - aluminum oxide particles; and Liner - application of a ceramic liner [IPS e.max Zirliner, Ivoclar Vivadent]); and 'thermocycling' (presence - 12,000 thermal cycles; 5-55ºC; or absence). The discs were veneered with porcelain (IPS e.max Ceram, Ivoclar Vivadent - 0.7 mm; totaling 1.4 mm thickness) according to ISO 6872:2015 for biaxial flexure strength testing. Fatigue tests (step-stress approach; 20 to 100 MPa; step of 10 MPa; 10,000 cycles per step; 10 Hz frequency) were run, followed by the data analysis (Kaplan-Meier and Mantel-Cox post-hoc tests). Analysis of roughness, topography, crystallographic phase arranges and fractography were also executed., Results: The surface treatment and thermocycling did not influence the porcelain crack nor delamination resistance. When only comparing the surface treatments for crack resistance outcome, the liner application depicted the worst fatigue performance in comparison to grinding and air-abrasion, while all groups were similar for delamination., Conclusions: Neither the surface treatment of the zirconia nor the thermocycling influences the porcelain crack resistance or the resistance to delamination of the bilayer porcelain-veneered zirconia specimens.

Purpose: To evaluate the influence of quantity and positioning of veneered zirconia specimens during firing of porcelain on their fatigue performance and colorimetric differences., Methods: Bilayer discs (Ø=15 mm) were made, following ISO 6872 guidelines, using a Y-TZP core (yttria-stabilized tetragonal zirconia polycrystal ceramic; VITA In-Ceram YZ) and a feldspathic veneering material (VITA VM9), being both layers with 0.7 mm thickness. Y-TZP discs were sintered, the veneering material was applied over it, and the bilayer specimens were fired according to two factors (n=20): 'quantity' (1 or 5 samples per firing cycle; G1 and G5 groups respectively) and 'positioning' of the specimens inside the furnace (center or periphery of the refractory tray; G5C and G5P groups, respectively). The CIEL*a*b* parameters were recorded with a spectrophotometer and the color difference (ΔE 00 ) and translucency (TP 00 ) were calculated using CIEDE2000 equations. The step-stress fatigue test was performed with the veneer facing down (region of tensile stress concentration), 10 Hz frequency, initial tension of 20 MPa for 5,000 cycles, followed by steps of 10,000 cycles using a step size of 10 MPa, up to 100 MPa; data from strength and number of cycles for failure were recorded for statistical analysis., Results: Unacceptable color differences (ΔE 00 >1.8) were observed comparing G5C vs. G1 (quantity) and G5C vs. G5P (positioning), meanwhile translucency parameters were not affected. Besides, only the 'quantity' factor influenced the fatigue performance (G1>G5C). None of the tested specimens survived beyond 90N and/or 75000 cycles., Conclusions: The quantity and position of the specimens during firing influence the final color of porcelain-veneered zirconia, and firing one specimen per cycle improved the fatigue performance of the bilayer system.

Objective: This study aimed to assess the characteristics of different designs of systematic reviews (SRs) registered in the International Prospective Register of Systematic Reviews (PROSPERO) about COVID-19., Methods: The search was performed in the PROSPERO database using the strategy proposed by the database and considered only human studies. The last date of the search was April 27, 2020. Full text of all records was accessed, and data were extracted by a single researcher, which was further double-checked by another researcher. A descriptive analysis was performed considering record characteristics using tables., Results: We included 564 records from which the vast majority were registered as SRs (n = 513, 91%). In general, we found poor reporting and missing or confusing information, since 84% of the records (n = 474) did not report the full search that would be adopted, 16% (n = 90) did not report clearly the databases that would be used, and 49.1% (n = 277) did not report the number of primary outcomes. The main focus of most of the records involved clinical, epidemiological, complication, and laboratory characteristics (n = 173, 30.7%) or the treatment of COVID-19 (n = 138, 24.5%)., Conclusion: A large number of SRs about COVID-19 have been conducted, and many of the assessed records were poorly reported and would be difficult to replicate. Besides, collected data points to an epidemic of redundant reviews on COVID-19., (© 2021 Chinese Cochrane Center, West China Hospital of Sichuan University and John Wiley & Sons Australia, Ltd.)

Purpose: The aim of this study was to inspect the mechanical fatigue behavior of an implant-supported restorative system using polyether ether ketone (PEEK) and yttria partially stabilized zirconia polycrystals (YZ) as materials for customized definitive implant-supported hybrid abutments, supporting two types of all-ceramic restorations: translucent zirconia (TZ) and lithium disilicate (LD) monolithic crowns., Materials and Methods: Forty Morse taper implants were included in epoxy resin. Titanium intermediary abutments were placed, and the specimens were randomly allocated into four groups (n = 10) according to the customized hybrid abutment material (PEEK or YZ) and the monolithic crowns (TZ or LD) representing a maxillary central incisor crown. The specimens were subjected to a mechanical fatigue test (step-stress analysis) by means of an initial 200-N load for 5,000 cycles and subsequent increase of 50 N (step-size) at each 10,000 cycles, until failure occurred. The load at failure and number of cycles until failure were recorded; survival probabilities and specimen displacement were calculated for each step. The failure pattern was evaluated, and the Weibull modulus was obtained for each condition., Results: Fatigue of both types of crowns was not influenced by the abutment material (LD-PEEK = LD-YZ; TZ-PEEK = TZ-YZ). In the PEEK abutment, the values obtained in the LD and TZ crowns showed no statistical difference; however, in the YZ abutment, the TZ crown presented a load at failure value that was statistically higher than that for LD. Failure pattern analysis revealed a higher prevalence of crown fracture for LD groups, while screw/implant platform fractures were shown for TZ groups., Conclusion: YZ and PEEK hybrid abutments promoted similar fatigue levels regardless of the crown materials, TZ crowns promoted a higher fatigue level than LD ones when associated with YZ abutments, and LD crowns promoted a similar fatigue level to TZ ones when associated with PEEK custom abutments. Higher prevalence of crown fractures was shown for LD and screw/implant platform fractures for TZ groups.

This study evaluated the distinct conditioning effect of the intaglio surface of bonded fully-stabilized zirconia (FSZ) simplified restorations on the mechanical fatigue behavior of the set prior to and after aging. Ceramic disc shaped specimens (Ø= 10 mm and 1 mm thick) were randomly allocated into 14 groups considering: "surface treatments" (Ctrl: no-treatment; PM: universal primer; GLZ: low-fusing porcelain glaze; SNF: 5 nm SiO 2 nanofilm deposition; AlOx: air-abrasion with aluminum oxide; SiC: air-abrasion with silica-coated aluminum oxide; 7%Si: air-abrasion with 7% silica-coated aluminum oxide); and "aging" (baseline: 24 h at 37 °C in water; or aged: 90 days at 37 °C in water + 12,000 thermal cycles). The discs were treated, luted with resin cement onto the dentin analog, subjected to aging or not, and then tested under a step-stress fatigue test at 20 Hz, 10,000 cycles/step, step-size of 100N starting at 200N, and proceeding until failure detection. Fractographic, topographic, surface roughness, contact angle, and atomic force microscopy analyzes were performed. The surface treatments at baseline led to statistically similar fatigue failure loads (953N-1313N), except for GLZ (1313N), which was significantly higher than 7%Si (953 N). Meanwhile, Ctrl had 40% pre-test failures (debonding) after aging, and therefore the worst fatigue performance (notable decrease in fatigue results), while all the other groups presented superior and statistically similar fatigue behavior (973-1271N). In fact, when considering baseline Vs aging conditions, stable fatigue results could only be noted when using surface treatments. In conclusion, internal surface treatments of FSZ ceramic restorations are mandatory for fatigue behavior stability after aging the restorative set, while non-treatment induced unstable results., (Copyright © 2020 Elsevier Ltd. All rights reserved.)

Introduction: Sepsis is a systemic inflammatory response to suspected or confirmed infection. Clinical evaluations are essential for its early detection and treatment. Blood cultures may take as long as 2 days to yield a result and are not always reliable. However, recent studies have suggested that neutrophil CD64 expression may be a sensitive and specific alternative for the diagnosis of systemic infection., Objective: The objective of the study was to analyze the difference in CD64 values between subjects with systemic inflammatory response syndrome (SIRS), suspected or confirmed sepsis, who meet diagnostic criteria for SIRS upon arriving at an emergency department., Materials and Methods: This was a prospective observational cohort study, an accuracy study of CD64 prospectively evaluated. The sample consisted of 109 patients aged 18 years with criteria for SIRS on arrival to emergency department. CD64 expression was measured within 6 h of hospital admission and once again after 48 h., Results: ROC curve analysis suggested that a cutoff of 1.45 for CD64 expression could diagnose sepsis with a sensitivity of 0.85, a specificity of 0.75, an accuracy of 82.08%, a positive predictive value of 0.96, a negative predictive value of 0.38 and a positive likelihood ratio of 3.33. The area under the curve was 0.83., Conclusion: CD64 seems to be a useful, sensitive, and specific biomarker in discriminating between SIRS and sepsis., Competing Interests: There are no conflicts of interest.

The objective of this study was to perform a systematic review of articles that followed up the psychological outcomes of interventions in patients with disorders of sexual development. The analysis focused on the methodological quality of the studies and the assumptions on the evaluation of the intervention outcomes. The review signaled the need for better consideration about the complexity of intersexuality and for a shift from the anatomical/functional/aesthetic to the subjective outcomes related to patient's quality of life. Furthermore, it is suggested that the interventions should be better investigated, given the lack of evidence for the necessity of early procedures., (© The Author(s) 2015.)

Background: Dengue fever is one of the most common tropical diseases worldwide. Early detection of the disease, followed by intravenous fluid therapy in patients with dengue hemorrhagic fever (DHF) or with warning signs of dengue has a major impact on the prognosis. The purpose of this study is to describe the care provided in a hydration tent, including early detection, treatment, and serial follow-up of patients with dengue fever., Findings: The analysis included all patients treated in the hydration tent from April 8 to May 9, 2008. The tent was set up inside the premises of the 2nd Military Firemen Group, located in Meier, a neighborhood in Rio de Janeiro, Brazil. The case form data were stored in a computerized database for subsequent assessment. Patients were referred to the tent from primary care units and from secondary city and state hospitals. The routine procedure consisted of an initial screening including vital signs (temperature, blood pressure, heart rate, and respiratory rate), tourniquet test and blood sampling for complete blood count. Over a 31-day period, 3,393 case recordings were seen at the hydration tent. The mean was 109 patients per day. A total of 2,102 initial visits and 1,291 return visits were conducted. Of the patients who returned to the hydration tent for reevaluation, 850 returned once, 230 returned twice, 114 returned three times, and 97 returned four times or more. Overall, 93 (5.3%) patients with DHF seen at the tent were transferred to a tertiary hospital. There were no deaths among these patients., Discussion: As the epidemics were already widespread and there were no technical conditions for routine serology, all cases of suspected dengue fever were treated as such. Implementing hydration tents decrease the number of dengue fever hospitalizations.

The effect of neem, Azadirachta indica A. Juss, on some biological parameters of Mahanarva fimbriolata (Stil) (Hemiptera: Cercopidae) was studied in the laboratory by using NeemAzal-T/S, Nimkol-LS, and an aqueous neem seed extract. Initially, the LC,, was estimated for nymphs. Later, nymphs fed on sugarcane, Saccharum officinarum L., roots were sprayed with the respective LC,, for each product. The adults were maintained in cages on sugarcane plants sprayed at the base with the maximum rate recommended commercially for the crop (3 liter/ha). Moistened cotton discs surrounding the base of the plant were used as oviposition substrates. The LCso values estimated for NeemAzal, Nimkol, and aqueous extract were 0.014, 0.225, and 0.611%, respectively. There was a reduction in spittlebug longevity, regardless of sex, in relation to the control. Males exposed to the neem products, and aqueous extract showed longevity reductions of approximately 50%, whereas for females the reductions were 55-60%. The neem products and extract reduced fecundity by 75-85%. Morphological and physiological changes were observed in 9% of the eggs from individuals submitted to NeemAzal. Neem-based products, especially NeemAzal, have potential for the control of M. fimbriolata.