Search

The classical method for evaluating the waveguide ability only focuses on the optical loss coefficient. However, for the micro- or submicroscale, an organic waveguide is demonstrated by the present study whose scale effect should not be neglected. We found that the optical loss coefficient increased remarkably when decreasing the sectional size of the microfibers. Furthermore, simulations based on Finite-Difference Time-Domain also demonstrated the size-dependent effect of the waveguide. Both the experimental and simulating results showed that the optical loss coefficient converges to a certain value, which means that the scale effect can be neglected as the sectional size is large enough. On the basis of the present study, we suggest that the scale-dependent effect on the sectional size of the waveguide should be investigated by evaluating the waveguide ability by the optical loss coefficient.

Titanium dioxide (TiO 2 ; as a potential photosensitizer) has good photocurrent performance and chemical stability but often exhibits low utilization efficiency under ultraviolet (UV) region excitation. Herein, we devised a near-infrared light-to-UV light-mediated photoelectrochemical (PEC) aptasensing platform for the sensitive detection of carcinoembryonic antigen (CEA) based on core-shell NaYF 4 :Yb,Tm@TiO 2 upconversion microrods by coupling with target-triggered rolling circle amplification (RCA). The upconversion microrods synthesized through the hydrothermal reaction could act as a photosensing platform to convert the near-infrared (near-IR) excitation into UV emission for generation of photoinduced electrons. The target analyte was determined on a functional magnetic bead by using the corresponding aptamers with a sandwich-type assay format. Upon target CEA introduction, a complex was first formed between capture aptamer-1-conjugated magnetic bead (Apt1-MB) and aptamer-2-primer DNA (Apt2-pDNA). Thereafter, the carried primer DNA by the aptamer-2 paired with linear padlock DNA to trigger the RCA reaction. The guanine (G)-rich product by RCA reaction was cleaved by exonuclease I and exonuclease III (Exos I/III), thereby resulting in the formation of numerous individual guanine bases to enhance the photocurrent of core-shell NaYF 4 :Yb,Tm@TiO 2 upconversion microrods under near-IR illumination (980 nm). Under optimal conditions, the near-IR light-mediated PEC aptasensing system could exhibit good photoelectrochemical response toward target CEA and allowed for the detection of target CEA as low as 3.6 pg mL -1 . High reproducibility and good accuracy were achieved for analysis of human serum specimens. Importantly, the near-IR-activated PEC aptasensing scheme provides a promising platform for ultrasensitive detection of other biomolecules.

A direct method has been used for the first time, to compute effective atomic numbers (Z eff) of water, air, human tissues, and some organic and inorganic compounds, for total electron proton and alpha particle interaction in the energy region 10 keV-1 GeV. The obtained values for Z eff were then compared to those obtained using an interpolation procedure. In general, good agreement has been observed for electrons, and the difference (%) in Z eff between the results of the direct and the interpolation method was found to be <10 % for all materials, in the energy range from 10 keV to 1 MeV. More specifically, results of the two methods were found to agree well (Dif. <10 %) for air, calcium fluoride, kapton polyimide film, paraffin wax and plastic scintillator in the entire energy region with respect to the total electron interaction. On the other hand, values for Z eff calculated using both methods for protons and alpha particles generally agree with each other in the high-energy region above 10 MeV.

In the welding process between similar or dissimilar materials, inserting an intermediate layer and pressure assistance are usually thought to be necessary. In this paper, the direct welding between alumina-silicate glass and metal (aluminum, copper, and steel), under exposure from 1 kHz femtosecond laser pulses without any auxiliary processes, is demonstrated. The micron/nanometer-sized metal particles induced by laser ablation were considered to act as the adhesive in the welding process. The welding parameters were optimized by varying the pulse energy and the translation velocity of the sample. The shear joining strength characterized by a shear force testing equipment was as high as 2.34 MPa. This direct bonding technology has potential for applications in medical devices, sensors, and photovoltaic devices.

Radiation transport simulation models can provide estimations of radiation effects such as detector response and detection capabilities. The objective of this research was to develop a methodology for quick, efficient, and effective determination of the composition of shielding materials to be used in radiation transport models. A C++ code, MatFit, was developed that used the concept of densitometry and the iterative method developed for the Spectrum Analysis by Neutron Detectors II (SAND II) computer program to estimate the elemental composition of shielding materials. These results were compared to previous neutron activation analysis (NAA) on the same samples. It was determined that densitometry provided an elemental approximation that yielded an attenuation rate within 10% of that found through NAA but requires much fewer resources, as well as less time. From this research, it is recommended that the developed method and C++ program be used when constructing models for detector response.

An approach for the theoretical evaluation of the damage threshold in optical interference coatings that combine metal and dielectric films is presented. The model that is used combines a matrix formalism to describe the film system with the two temperatures model that describes the energy transfer and the temperatures of electrons and lattice in a solid submitted to a laser irradiation at the femtosecond time scale. With this approach the thermal consequences due to the ultrafast absorption of the metal film can be evaluated in the multilayer stack for single or multiple pulses. Some applications are presented for the case of broadband mirrors for ultrashort pulses with low dispersion. Particularly we study the impact of the metal film (metal element, thickness) and the design on the Laser Induced Damage Threshold in the sub picosecond regime.

Polyethylene is the most prevalent plastic and is commonly used as a packaging material. Despite its common use, there are not many studies on imparting functionalities to those films which can make them more desirable for frozen food packaging. Here, commercial low-density polyethylene (LDPE) films were oxidized by UV-ozone (UVO) treatment to obtain a negatively charged hydrophilic surface to allow fabrication of functional multilayers. An increase in hydrophilicity was observed when films were exposed to UVO for 4 min and longer. Thin multilayers were formed by dipping the UVO-treated films into biopolymer solutions, and extracellular ice nucleators (ECINs) were immobilized onto the film surface to form a functional top layer. Polyelectrolyte adsorption was studied and confirmed on silicon wafers by measuring the water contact angles of the layers and investigating the surface morphology via atomic force microscopy. An up to 4-5 °C increase in ice nucleation temperatures and an up to 10 min decrease in freezing times were observed with high-purity deionized water samples frozen in ECIN-coated LDPE films. Films retained their ice nucleation activity up to 50 freeze-thaw cycles. Our results demonstrate the potential of using ECIN-coated polymer films for frozen food application.

Adaptive mass fabrication method based on laser-induced plasmonic local surface defunctionalization was suggested to realize solution-based high resolution self-patterning on transparent substrate in parallel. After non-patterned functional monolayer was locally deactivated by laser-induced metallic plasma species, various micro/nano metal structures could be simultaneously fabricated by the parallel self-selective deposition of metal nanoparticles on a specific region. This method makes the eco-friendly and cost-effective production of high resolution pattern possible. Moreover, it can respond to design change actively due to the broad controllable range and easy change of key patterning specifications such as a resolution (subwavelength~100 μm), thickness (100 nm~6 μm), type (dot and line), and shape.

Switchable metamaterials offer unique solutions for efficiently manipulating electromagnetic waves, particularly for terahertz waves, which has been difficult since naturally occurring materials rarely respond to terahertz frequencies controllably. However, few terahertz modulators demonstrated to date exhibit simultaneously low attenuation and high modulation depth. In this letter we propose a new class of electrically-tunable terahertz metamaterial modulators employing metallic frequency-selective-surfaces (FSS) in conjunction with capacitively-tunable layers of electrons, promising near 100% modulation depth and < 15% attenuation. The fundamental departure in our design from the prior art is tuning enabled by self-gated electron layers that is independent from the metallic FSS. Our proposal is applicable to all possible electrically tunable elements including graphene, Si, MoS(2), oxides etc, thus opening up myriad opportunities for realizing high performance switchable metamaterials over an ultra-wide terahertz frequency range.

In this study, it has been investigated the disinfection of Korean cultural artifacts by gamma irradiation, simulating the absorbed dose distribution on the object with the Monte Carlo methodology. Fungal contamination was identified on two traditional Korean agricultural tools, Hongdukkae and Holtae, which had been stored in a museum. Nine primary species were identified from these items: Bjerkandera adusta, Dothideomycetes sp., Penicillium sp., Cladosporium tenuissimum, Aspergillus versicolor, Penicillium sp., Entrophospora sp., Aspergillus sydowii, and Corynascus sepedonium. However, these fungi were completely inactivated by gamma irradiation at an absorbed dose of 20kGy on the front side. Monte Carlo N Particle Transport Code was used to simulate the doses applied to these cultural artifacts, and the measured dose distributions were well predicted by the simulations. These results show that irradiation is effective for the disinfection of cultural artifacts and that dose distribution can be predicted with Monte Carlo simulations, allowing the optimization of the radiation treatment., (Copyright © 2012 Elsevier Ltd. All rights reserved.)

Direct laser writing is widely used for fabrication of subsurface, three dimensional structures in transparent media. However, the accessible volume is limited by distortion of the focussed beam at the sample edge. We determine the aberrated focal intensity distribution for light focused close to the edge of the substrate. Aberrations are modelled by dividing the pupil into two regions, each corresponding to light passing through the top and side facets. Aberration correction is demonstrated experimentally using a liquid crystal spatial light modulator for femtosecond microfabrication in fused silica. This technique allows controlled subsurface fabrication right up to the edge of the substrate. This can benefit a wide range of applications using direct laser writing, including the manufacture of waveguides and photonic crystals.

One of the limits of conventional scanning multiphoton microfabrication is its low throughput due to point-by-point processing. In order to surpass this limit, a multiphoton microfabrication system based on spatiotemporal focusing and patterned excitation has been developed to quickly provide three-dimensional (3D) freeform polymer microstructures. 3D freeform polymer microstructures using Rose Bengal as the photoinitiator are created by sequentially stacking two-dimensional fabricating patterns. The size of each fabrication area can be larger than 300 × 170 μm2 (full width at half maximum). Compared to conventional scanning multiphoton excitation and fixed mask pattern generation, this approach offers freeform microstructures and a greater than three-order increase in fabrication speed. Furthermore, the system is capable of optically sectioning the fabricated microstructures for providing 3D inspection.

Rod-shaped nanocrystalline cellulose (NCC) was prepared from microcrystalline cellulose (MCC) using the purely physical method of high-intensity ultrasonication. Scanning electron microscopy, transmission electron microscopy, and X-ray diffraction was used for the characterization of the morphology and crystal structure of the material. The thermal properties were investigated using thermogravimetric analysis. The reinforcement capabilities of the obtained NCC were investigated by adding it to poly(vinyl alcohol) (PVA) via the solution casting method. The results revealed that the prepared NCC had a rod-shaped structure, with diameters between 10 and 20 nm and lengths between 50 and 250 nm. X-ray diffraction results indicated that the NCC had the cellulose I crystal structure similar to that of MCC. The crystallinity of the NCC decreased with increasing ultrasonication time. The ultrasonic effect was non-selective, which means it can remove amorphous cellulose and crystalline cellulose. Because of the nanoscale size and large number of free-end chains, the NCC degraded at a slightly lower temperature, which resulted in increased char residue (9.6-16.1%), compared with that of the MCC (6.2%). The storage modulus of the nanocomposite films were significantly improved compared with that of pure PVA films. The modulus of PVA with 8 wt.% NCC was 2.40× larger than that of pure PVA., (Crown Copyright © 2011. Published by Elsevier B.V. All rights reserved.)

We investigate thermal emission from a metamaterial wire medium embedded in a dielectric host and highlight two different regimes for efficient emission, respectively characterized by broadband emission near the effective plasma frequency of the metamaterial, and by narrow-band resonant emission at the band-edge in the Bragg scattering regime. We discuss how to control the spectral position and relative strength of these two emission mechanisms by varying the geometrical parameters of the proposed metamaterial and its temperature., (© 2012 Optical Society of America)

We propose a set of postulates to describe the mechanical interaction between a plane-wave electromagnetic pulse and a dispersive, dissipative slab having a refractive index of arbitrary sign. The postulates include the Abraham electromagnetic momentum density, a generalized Lorentz force law, and a model for absorption-driven mass transfer from the pulse to the medium. These opto-mechanical mechanisms are incorporated into a one-dimensional finite-difference time-domain algorithm that solves Maxwell's equations and calculates the instantaneous force densities exerted by the pulse onto the slab, the momentum-per-unit-area of the pulse and slab, and the trajectories of the slab and system center-of-mass. We show that the postulates are consistent with conservation of global energy, momentum, and center-of-mass velocity at all times, even for cases in which the refractive index of the slab is negative or zero. Consistency between the set of postulates and well-established conservation laws reinforces the Abraham momentum density as the one true electromagnetic momentum density and enables, for the first time, identification of the correct form of the electromagnetic mass density distribution and development of an explicit model for mass transfer due to absorption, for the most general case of a ponderable medium that is both dispersive and dissipative., (© 2012 Optical Society of America)

Buried channel waveguides in Nd:LuVO<4 were fabricated by femtosecond laser writing with the double-line technique. The photoluminescence properties of the bulk materials were found to be well preserved within the waveguide core region. Continuous-wave laser oscillation at 1066.4 nm was observed from the waveguide under ~809 nm optical excitation, with the absorbed pump power at threshold and laser slope efficiency of 98 mW and 14%, respectively.

We present direct UV-written waveguides and Bragg gratings operating at 780 nm. By combining two gratings into a Fabry-Perot cavity we have devised and implemented a novel and practical method of measuring the group delay of Bragg gratings.

Bursts of femtosecond laser pulses with a repetition rate of f = 38.5MHz were created using a purpose-built optical resonator. Single Ti:Sapphire laser pulses, trapped inside a resonator and released into controllable burst profiles by computer generated trigger delays to a fast Pockels cell switch, drove filamentation-assisted laser machining of high aspect ratio holes deep into transparent glasses. The time dynamics of the hole formation and ablation plume physics on 2-ns to 400-ms time scales were examined in time-resolved side-view images recorded with an intensified-CCD camera during the laser machining process. Transient effects of photoluminescence and ablation plume emissions confirm the build-up of heat accumulation effects during the burst train, the formation of laser-generated filaments and plume-shielding effects inside the deeply etched vias. The small time interval between the pulses in the present burst train enabled a more gentle modification in the laser interaction volume that mitigated shock-induced microcracks compared with single pulses.

A path-folded infrared image spectrometer with five sub-gratings and five linear-array detectors was applied to a broadband optical monitoring (BOM) system for thin film deposition. Through in situ BOM, we can simultaneously acquire the thickness and refractive index of each layer in real time by fitting the measured spectra, and modify the deposition parameters during deposition process according to the fitting results. An effective data processing method was proposed and applied in the BOM process, and it shortened the data processing time and improved the monitoring efficiency greatly. For demonstration, a narrow band-pass filter (NBF) at 1540 nm with ~10 nm full width at half-maximum (FWHM) had been manufactured using the developed BOM system, and the results showed that this BOM method was satisfying for monitoring deposition of thin film devices.

Textile materials can be treated with some enzymes to improve their functionality. The usual enzymatic treatment hydrolyzes the textile surfaces that leads to increase the functional groups. Here, the polyester/wool fabric as a blend of fibers fabric was selected and treated with the two different types of enzymes to increase the surface activity with a propose of higher nano-TiO(2) adsorption. The fabric was first treated with proteases and lipases to hydrolyze the wool and the polyester surfaces, respectively. It has been then dipped into an ultrasound bath containing nano TiO(2) and cross-linking agent followed by curing. The cross-linking agent, butane tetracarboxylic acid (BTCA), also assisted to enhance the nano-particles adsorption and stabilization on the fabric surface. The self-cleaning properties of the fabrics were examined through evaluating the color removal from the stained fabric with Acid Blue 113. The antibacterial properties were determined by reduction growth of a Gram-negative bacteria E. coli. and the UV protection was assessed by UV-reflectance spectrum. The SEM pictures and EDX spectrums of some samples were also reported., (© 2011 The Authors. Photochemistry and Photobiology © 2011 The American Society of Photobiology.)

50 fs - 12 ps laser pulses are employed to ablate aluminum, copper, iron, and graphite targets. The ablation-generated momentum is measured with a torsion pendulum. Corresponding time-resolved shadowgraphic measurements show that the ablation process at the optimal laser fluence achieving the maximal momentum is primarily dominated by the photomechanical mechanism. When laser pulses with specific laser fluence are used and the pulse duration is tuned from 50 fs to 12 ps, the generated momentum firstly increases and then remains almost constant, which could be attributed to the change of the ablation mechanism involved from atomization to phase explosion. The investigation of the ablation-generated momentum also reveals a nonlinear momentum-energy conversion scaling law, namely, as the pulse energy increases, the momentum obtained by the target increases nonlinearly. This may be caused by the effective reduction of the dissipated energy into the surrounding of the ablation zone as the pulse energy increases, which indicates that for femtosecond laser the dissipated energy into the surrounding target is still significant.

Optically induced ultrafast electronic excitations with sufficiently long lifetimes may cause strong effects on phase transitions like structural and nonmetal→metal ones and on supercooling, supersaturation, etc. Examples are the transitions diamond→graphite, graphite→graphene, non-metal→metal, solid→liquid and vapor→liquid, solid. Photoinduced formation of graphene and water condensation of saturated or supersaturated vapor due to increased bonding amongst water molecules are of particular interest. These nonequilibrium transitions are an ultrafast response, on a few hundred fs time scale, to the fast low to large energy electronic excitations. The energy of the photons is converted into electronic energy via electronic excitations changing the cohesive energy. This changes the chemical potential controlling the phase transition. In view of the advances in laser optics photon induced transitions are expected to become an active area in nonequilibrium physics and phase transition dynamics. Conservation laws like energy or angular momentum conservation control the time during which the transitions occur. Since the photon induced effects result from weakening or strengthening of the bonding between the atoms or molecules transitions like solid/liquid, etc can be shifted in both directions. Photoinduced transitions will be discussed from a unified point of view., (© 2011 IOP Publishing Ltd)

We study the optical force arising when isolated gold nanowire pairs and metamaterials with a gold nanowire pair in the unit cell are illuminated with laser radiation. Firstly, we show that isolated nanowire pairs are subject to much stronger optical forces than nanospheres due to their stronger electric and magnetic dipole resonances. We also investigate the properties of the optical force as a function of the length of the nanowires and of the distance between the nanowires. Secondly, we study the optical force in a metamaterial that consists of a periodic array of nanowire pairs. We show that the ratio of the size of the unit cell to the length of the nanowires determines whether the electric dipole resonance leads to an attractive or a repulsive force, and we present the underlying physical mechanism for this effect.

For the first time, in situ the hole shape evolution during ultrashort pulse laser drilling in semiconductor material is imaged. The trans-illumination of the sample at a wavelength of 1.06 µm is projected onto a standard CCD camera during the ablation, providing an image of the contour of the ablated structure perpendicular to the irradiation for drilling. This demonstrated technique enables a direct, high resolution investigation of the temporal evolution of the drilling process in the depth of the material without complex sample preparation or post processing.

Optical properties of composite restoratives, both cured and uncured, are of obvious importance in a procedure reliant on photoactivation, since they may affect light transmission and therefore materials conversion upon which mechanical properties and ultimate clinical performance are dependent. The objective of the present study was to evaluate simultaneous, real-time conversion, and the development of the temperature and optical properties. The dimethacrylate resin (Bis-GMA/TEGDMA 70/30mass%) was prepared at three filler loading (0, 35 or 70mass%: no fill, low and high fill, respectively) combined with three initiator concentrations (CQ/EDMAB: 0/0, 0.2/0.8 or 1.0/1.6mass%). Specimens were exposed to either low (50mWcm(-2)) or high (500mWcm(-2)) irradiance. Simultaneous conversion (near-IR peak area), temperature (thermocouple) and visible light transmission (UV-vis spectroscopy) measurements were conducted throughout the polymerization process. The refractive index of the resin rises linearly with conversion (r(2)=0.976), producing a refractive index match between resin/filler at approximately 58% conversion in these materials. The percentage increase in light transmission during conversion was greater for increasing filler levels. Higher CQ content led to maximum light transmission at slightly higher levels of conversion (60-65% and 50-55% for the high and low filled materials, respectively). The broad distribution of filler concentrations allows for the clinically relevant generalization that highly filled composites not only jeopardize absolute light transmission, conversion and depth of cure, but also demonstrate the complex interrelationship that exists between materials, processing conditions and the optical properties of dental composites., (Copyright 2009 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.)

The setting and development of strength of Portland cement concrete depends upon the reaction of water with various phases in the Portland cement. Nuclear resonance reaction analysis (NRRA) involving the (1)H((15)N,alpha,gamma)(12)C reaction has been applied to measure the hydrogen depth profile in the few 100 nm thick surface layer that controls the early stage of the reaction. Specific topics that have been investigated include the reactivity of individual cementitious phases and the effects of accelerators and retarders., (Copyright 2009 Elsevier Ltd. All rights reserved.)

The temperature dependence of the resonant wavelength of vertically coupled microring resonator can be controlled via internal stress caused by the thermo-optic and photo-elastic effects. In the case of strong internal stress, a polarization-independent microring resonator can be realized by controlling the device surface temperature using a heater module; the temperature dependence of TE and TM polarizations are different due to the internal stress and thus manipulating temperatures, the resonant wavelengths for TE and TM can be equalized at a specific temperature. In this study, the UV trimming of polarization-independent wavelength was demonstrated using UV-sensitive SiON as a core material. The temperature dependence of TE polarization was almost athermalized and that of TM was made negative by controlling internal stress. As a result, the simultaneous realization of the UV trimming and the polarization-independent microring was made possible more easily than before; the UV trimming can be done at room temperature due to the athermalized resonant wavelength for TE polarization.

Light transmission spectrum of a multilayer photonic crystal with a central liquid-crystal defect layer placed between crossed polarizers has been studied. Transmittance was varied due to the magnetically induced reorientation of the nematic director from homeotropic to planar alignment. Two notable effects were observed for this scheme: the spectral shift of defect modes corresponding to the extraordinary light wave and its superposition with the ordinary one. As a result, the optical cell allows controlling the intensity of interfering defect modes by applied magnetic field.

In order to more exactly predict femtosecond pulse laser induced damage threshold, an accurate theoretical model taking into account photoionization, avalanche ionization and decay of electrons is proposed by comparing respectively several combined ionization models with the published experimental measurements. In addition, the transmittance property and the near-field distribution of the 'moth eye' broadband antireflective microstructure directly patterned into the substrate material as a function of the surface structure period and groove depth are performed by a rigorous Fourier model method. It is found that the near-field distribution is strongly dependent on the periodicity of surface structure for TE polarization, but for TM wave it is insensitive to the period. What's more, the femtosecond pulse laser damage threshold of the surface microstructure on the pulse duration taking into account the local maximum electric field enhancement was calculated using the proposed relatively accurate theoretical ionization model. For the longer incident wavelength of 1064 nm, the weak linear damage threshold on the pulse duration is shown, but there is a surprising oscillation peak of breakdown threshold as a function of the pulse duration for the shorter incident wavelength of 532 nm.

Inverse lithography technology (ILT) treats photomask design for microlithography as an inverse mathematical problem. We show how the inverse lithography problem can be addressed as an obstacle reconstruction problem or an extended nonlinear image restoration problem, and then solved by a level set time-dependent model with finite difference schemes. We present explicit detailed formulation of the problem together with the first-order temporal and second-order spatial accurate discretization scheme. Experimental results show the superiority of the proposed level set-based ILT over the mainstream gradient methods.

We propose a scheme to induce transparency in one-dimensional disordered multilayers which are composed of negative permittivity and negative permeability metamaterials. First, analytical expressions for transparency condition are derived exactly, providing us a picture that complete tunneling in such kind of multiple-resonance system can be achieved if exponentially growing waves can compensate exponentially decaying waves. Second, a compensating method is used to realize this idea, and both simulations and experiments are performed in the microwave regime to confirm the theoretical analysis. Last, we have a discussion on how the coupling of resonances affects the transport properties of samples.

We report on an approach to ultraviolet (UV) photolithography and direct writing where both the exposure pattern and dose are determined by a complementary metal oxide semiconductor (CMOS) controlled micro-pixellated light emitting diode array. The 370 nm UV light from a demonstrator 8 x 8 gallium nitride micro-pixel LED is projected onto photoresist covered substrates using two back-to-back microscope objectives, allowing controlled demagnification. In the present setup, the system is capable of delivering up to 8.8 W/cm2 per imaged pixel in circular spots of diameter approximately 8 microm. We show example structures written in positive as well as in negative photoresist.

We present a planar design of a metamaterial exhibiting electromagnetically induced transparency that is amenable to experimental verification in the microwave frequency band. The design is based on the coupling of a split-ring resonator with a cut-wire in the same plane. We investigate the sensitivity of the parameters of the transmission window on the coupling strength and on the circuit elements of the individual resonators, and we interpret the results in terms of two linearly coupled Lorentzian resonators. Our metamaterial designs combine low losses with the extremely small group velocity associated with the resonant response in the transmission window, rendering them suitable for slow light applications at room temperature.

The first measurements of thermally induced depolarization in a [110] oriented cubic crystal at powerful heat release were made. It was demonstrated that depolarization in a crystal with such orientation may be less than in analogous crystals having orientation [001] or [111]. In a TGG crystal, for example, maximum depolarization value was 10% and dropped down to 3% with a further increase of radiation power in full conformity with the theoretical predictions.

A femtosecond fiber laser was applied to fabricate broadband directional couplers inside bulk glass for general power splitting application in the 1250 to 1650-nm wavelength telecom spectrum. The broadband response was optimized over the 400-nm bandwidth by tailoring the coupling strength and the waveguide interaction length to balance the differing wavelength dependence of the straight interaction and bent transition regions. High spatial finesse of the femtosecond-laser writing technique enabled close placement (approxiamtely 6 microm) of adjacent waveguides that underpinned the wavelength-flattened broadband response at any coupling ratio in the 0% to 100% range. The spectral responses were well-represented by coupled mode theory, permitting simple design and implementation of broadband couplers for bulk 3D optical circuit integration.

Ultra high molecular weight polyethylene, both pure and electron beam irradiated, was exposed to air and hyaluronic acid. Physical and mechanical analyses were performed in order to check the polymeric change due to the treatment. Pure UHMWPE, in fact, was modified by the hyaluronic acid that plasticizes the polymer. The electron irradiation cross links the chains and prevents their sliding in acid presence. A low irradiation dose is preferable rather than an high one. Low doses induce low amount of free radicals, witch react with oxygen and hyaluronic acid inducing low polymer degrade maintaining the initial mechanical performance. High doses degrade significantly the polymer properties.100 kGy irradiation in air can be applicable on the polyethylene as well as a compromise between the low mechanical performance improving and the material degradation.

We describe a sputtering system that can deposit composition spreads in an effectively UHV environment but which does not require the high-throughput paradigm to be compromised by a long pump down each time a target is changed. The system deploys four magnetron sputter guns in a cryoshroud (getter sputtering) which allows elements such as Ti and Zr to be deposited with minimal contamination by oxygen or other reactive background gases. The system also relies on custom substrate heaters to give rapid heating and cool down. The effectiveness of the gettering technique is evaluated, and example results obtained for catalytic activity of a pseudoternary composition spread are presented.

The feasibility of microwave dehydrating flax fiber was evaluated using a commercial domestic microwave oven at four power settings representing 200, 300, 400 and 500 Watt (W) power level. Due to the possibility of local heating and consequent fiber degradation, the changes in color of the flax fiber at different levels of temperature were also investigated. The dehydration processes at various power levels were simulated by Page model. Based on visual inspection, color analysis and scanning electron microscopy (SEM) of the fiber, it was revealed that discoloration of the fiber occurred at about 170 degrees C. At 200 and 300 W power level, after 10 minutes of dehydrating, the moisture content of the fiber reached from initial 7.9% close to 2.0 and 1.0%, respectively. For 400 W power level, the moisture content of the fiber dropped to 0. 10% in about 9.5 minutes. Major discoloration of the fiber was noticed when dehydration was proceed beyond 4.5 minutes for 500 W treatment. The Page model very well fitted the experimental data. The coefficients of determination calculated from the model and the experimental data increased with increase in applied microwave power

In recent years, lead has been recognized as a source of environmental pollution; this includes lead use for radiation shielding in radiotherapy. We looked for a new material that could be a lead substitute. We chose a material composed of tungsten and resin. We compared the attenuation coefficient of the material with those of lead and Lipowitz's metal, and found the material has a higher attenuation coefficient than the other two. The material may be used as a substitute for lead because it is easy to fabricate and friendly to the environment.

A parameter optimisation model is developed to find the parameters that have significant effects on homogeneous temperature distribution during microwave processing of materials. Electromagnetic, thermal and processing parameters are collected for a wide variety of materials and the heating profiles are calculated using a stationary 1D-electrothermal model. A measure of temperature homogeneity is obtained from the heating profiles by statistical calculations of normalised variance (the response variable). The processing parameters (power, temperature, size of the material sample) are optimisedfor all of these materials for a minimum normalised variance which allows maximum change of +/-3% Taverage on the T-distribution to meet most of the industrial process requirements. This mathematical model suggests a group of materials, which requires modifications in processing conditions to achieve uniform heating.

It is not rare to hear arguments against the use of thermocouples for taking temperatures in processes that are taking place under microwave fields. However, the simplicity of this device makes it attractive to consider its use. One question that arises when thermocouples are employed is whether the electric field perturbs the measurement, and if the thermocouple affects the processing. The process that was chosen for conducting this test was the synthesis of spinel (MgAl2O4) using microwaves as a power supply and hematite (Fe2O3) as an additive for both spinel formation promotion and susceptor. The alumina-based systems are very important to study because this is one of the most common ingredients in refractory materials. There are many discussions about the improvement of the process when microwaves are used, but a kinetic comparison cannot be performed if the temperature is unknown, and that is the reason for emphasizing the measurement techniques. The analysis of the obtained samples was carried out by X-ray diffraction of powders. The results of this work show that there is no difference between the products obtained when the thermocouple was inserted in the system, compared to processing without it; hence the thermocouple is appropriate for this application.

Lead is a hazardous material, and the U.S. Congress has mandated the rapid reduction of all hazardous waste generation as a matter of national policy. With the large amount of plutonium handling in numerous projects including the development of mixed oxide (MOX) fuel, 238Pu power sources, etc., hand glove protection for the emitted alpha, beta, and low energy photons is an important issue. Leaded gloves are the prime shields used for radiological hand protection. U.S. Department of Energy laboratories require a substitute material for the lead oxide in the gloves as a way to reduce mixed waste. To solve this problem, a new blend of non-hazardous materials that have the same radiological properties and approximately the same cost of production have been investigated. The investigations have produced alternative materials using calculations and experiments. The selection of the constituent compounds for the new composite materials was based on the k-absorption edge energy of the main constituent element(s) in the compounds. The formulations of these composites were fashioned on the principle of blending Neoprene rubber formulation with several constituent compounds. Calculations based on the Lambert-Beer attenuation law together with the mass attenuation coefficient values from the XCOM cross section database program were used to determine the transmission fractions of these proposed composite materials. Selected composite materials that compared favorably with the leaded-Neoprene were fabricated. These fabricated composite materials were tested with attenuation experiments and the results were in excellent agreement with the calculations using the Lambert-Beer attenuation law.

The material properties of greatest importance in microwave processing of a dielectric are the complex relative permittivity epsilon = epsilon'-jepsilon", and the loss tangent, tan delta = epsilon"/epsilon'. This paper describes two convenient laboratory based methods to obtain epsilon', epsilon" and hence tan delta of fibre-reinforced thermoplastic (FRTP) composites. One method employs a microwave network analyzer in conjunction with a waveguide transmission technique, chosen because it provides the widest possible frequency range with high accuracy. The values of the dielectric constant and dielectric loss of glass fibre reinforced (33%) low density polyethylene, LDPE/GF (33%), polystyrene, PS/GF (33%), and Nylon 66/GF (33%), were obtained. Results are compared with those obtained by another method using a high-temperature dielectric probe.

Nanocomposites of Zn/Al-layered double hydroxide(anthraquinone-2,6-disulfonate) were synthesized by spontaneous direct assembly of inorganic and organic phases from aqueous solution. Powder X-ray diffraction patterns showed that a pure, single nanocomposite phase of good crystallinity was obtained using 1.0 M antraquinone-2,6-disulfonate ion (AQ26) and aging at 80 degrees C using conventional heating for 7 days or 0.5 h under microwave radiation, and these samples are denoted as ZAAN26C or ZAAN26MH, respectively. Zn/Al-nitrate-layered double hydroxide synthesized by a conventional method (ZANLC) showed a basal spacing of 8.3 A while both the nanocomposites showed 18.8 A as a result of AQ26 intercalation. FTIR study showed that the resulting nanocomposites are free from nitrate, the co-anion present in the mother liquor, indicating that only AQ26 is preferred during intercalation for the formation of the nanocomposite. The Brunauer, Emmet and Teller (BET) and micropore surface areas for ZAAN26C decreased relative to the ZANLC from 16.2 to 4.7 and 1.6 to 1.3 m2/g, respectively. These results indicate that AQ26 can be rapidly interdcalated in layered double hydroxide using microwave-aging resulting in a nanocomposite.