Search

A two-step method for investigating the stiffnesses and failure loads of vertebral bodies is presented. It is based on the representation of the spine in a global finite element model of structural elements. A detailed model of two interconnected vertebrae and an intervertebral disc was implemented. Calculations on this model are shown which illustrate the dependencies of structural stiffnesses on vertebral body properties. These structural stiffnesses can then be used to represent the spine in the global model.

In tissue engineering and regenerative medicine mesenchymal stem cells (MSC) are widely used to replace and restore the function of dysfunctional or missing tissue. Recent studies have shown significant enhancements of the in vivo healing process following dentofacial bone augmentation procedures employing stem cell-loaded xenografts. We conducted experimental and numerical investigations in perfusion flow bioreactor-xenograft-systems to identify flow conditions as well as bioreactor design features that allow for homogeneous MSC-distribution in Geistlich Bio- Oss Block xenografts. Pressure gradient - velocity characteristics and flow distributions were investigated experimentally and numerically for two bioreactor designs at steady-state flow conditions with Reynolds numbers (Re) ranging from 0.01 ≤ Re ≤ 0.32. Distilled water at 20°C with a dynamic viscosity of 1.002 mPa∙s and a density of 998 kg/m3 was used. The geometry of the xenograft utilized in three-dimensional computational fluid dynamics (CFD) simulation was obtained by means of micro-computed tomography (μCT) at an isotropic spatial resolution of 9.5 μm. The permeability values calculated from the experimental data are in good accordance with the numerical results. The investigations showed that the increase of the inflow- and outflow-area diameter, as well as the decrease of the volumetric flow rate, result in a decreasing heterogeneity of the flow distribution within the xenograft. The calculated wall shear stress rates in the three-dimensional (3D) scaffold range from 1∙10-12Pa ≤ τ ≤ 0.2 Pa. Experimentally validated CFD simulations introduced in this study provide an applicable tool to assess optimal flow conditions for homogeneous MSC distribution in bioreactor-xenograft-systems.

In dentofacial surgery, augmentation procedures employing xenografts have become a reliable treatment. Recent studies, however, have shown significant enhance-ments of the in vivo bone tissue augmentation using mesenchymal stem cells loaded into bone grafts. We conducted experimental and numerical investigations in flow perfusion systems to determine flow conditions which allow for homogenous stem cell distribution in BioOss Block (Geistlich Pharma AG, Switzerland) xenografts. Pressure gradient-velocity characteristics and flow distributions were investigated experimentally and numerically at steady state flow conditions with Reynolds numbers (Re) ranging from 0.01 ≤ Re ≤ 0.40. Distilled water at 20°C with a dynamic viscosity of 1.002 mPa.s and a density of 998 kg/m3 was used. The geometry utilized in three-dimensional computa-tional fluid dynamics (CFD) simulation was obtained by means of micro-computed tomography (μCT). Results of CFD analysis are in good accordance with experimental data. The comparison of the pressure gradient-velocity characteris-tics for experimental and numerical data yields a relative error of 3.6%. According to Darcy’s law for creeping fluid flow the experimentally determined permeability is 2.55.10-9 m2. Moreover, numerical flow distribution analysis shows an increasingly heterogenic streamline distribution for increasing Reynolds numbers. Experimentally validated CFD simulations introduced in this study provide a tool to assess optimal flow conditions for a homogenous stem cell distribution in perfusion flow systems.

The investigation of matching of endoprosthesis tibial components to the bone cross section is of interest for the manufacturer as well as for the surgeon. On the one hand, a systemic design of the prosthesis and the assortment is possible, on the other hand, a better matching implantation is enabled on the basis of experience of this study. CT sections were segmented manually using a CAD system and fitted by spline functions, then superseded with cross sections of the tibial component of a modified Hintermann H3 prosthesis. The principal moments of inertia, the direction of the principal axes and the area of the section were evaluated. Based on the relative differences of the principal moments of inertia, recommendations for application of the different prosthesis size and its selection with the surgery can be made.

The Bauschinger effect is a phenomenon metals show as a result of plastic deformation. After a primary plastic deformation the yield strength in the opposite loading direction decreases. The aim of this study is to investigate if there is a phenomenon similar to Bauschinger effect in thermoplastic polymers for stent application that would influence the mechanical properties of these biodegradable implants. Combined uniaxial tensile with subsequent compression tests as well as conventional compression tests without prior tensile loading were performed using biodegradable polymers for stent application (PLLA and a PLLA based blend). Comparing the results of compression tests with prior tensile loading to the compression-only tests a decrease in compressive strength can be observed for both of the tested materials. The conclusion of the performed experiments is that there is a phenomenon similar to Bauschinger effect not only in metallic materials but also in the examined thermoplastic polymers. The observed reduction of compressive strength as a consequence of prior tensile loading can influence the mechanical behaviour, e.g. the radial strength, of polymeric stents after sustaining a complex load history due to crimping and expansion.

For the investigation of reaction moments of wrist joint with external fixator, a test device was developed that allows a well-defined investigation of the joint loads during hand flexion movements. The reaction moments are considered as a measure for the joint loads due to the constraint forces, which occur with differences of the rotation axis of the fixator device from the physiological rotation axis of the wrist joint. The developed test device allows a dynamic momentum load application into the wrist by a servohydraulic testing machine. This testing device converts the force to a moment by a constant lever arm and allows thereby the measurement of the reaction moments by the force load cell of the testing machine. Measurements on cadaveric wrist joints with external fixator can be thereby performed under reproducible conditions. The cadaveric wrist joints can be integrally casted into bone cement and thereby clamped to the testing device. Preliminary experiments with artificial bones showed that forces within the measuring range of the load cell of the testing machine can be measured. The design of the test device is presented. Hence, the requirements for measurements of the reaction moments with wrists with external fixator for distal radius fractures under dynamic loads are created.

Theoretical and experimental investigations were carried out for development of human lens implants made from hydrogel material. The material properties were measured and implemented in a Finite element model. Though the material is still too stiff for accommodative lenses, the theoretical and experimental foundations for the implant development were established.

Hydrogels were introduced as suitable materials for applications in, e.g., medical, agriculture, or daily life areas. Swelling characteristics of a hydrogel are important and must be precisely known for various fields of application. In medicine, where hydrogels are used as implants or drug delivery systems, precise knowledge of the swelling behavior is essential. Especially in ophthalmology as part of cataract surgery, the visco‐elastic properties of the hydrogels could even allow for the restoration of accommodation. The easiest way to describe the swelling is by measuring the swelling ratio, generally done by scaling. Besides that, it can also be done by volume investigations. The similarities and differences are studied on five hydrogel samples made of methyl methacrylate and N‐vinyl pyrrolidone. Additionally, a first camera‐based approach, potentially providing an automated, quasi‐continuous non‐contact method for swelling kinetics investigations, is described. [ABSTRACT FROM AUTHOR]

Abstract Background It is often suggested that sagittal instability at the first tarso-metatarsal joint level is a primary factor for hallux valgus and that sagittal instability increases with the progression of the deformity. The assessment of the degree of vertical instability is usually made by clinical evaluation while any measurements mostly refer to a static assessment of medial ray mobility (i.e. the plantar/dorsal flexion in the sagittal plane). Testing methods currently available cannot attribute the degree of mobility to the corresponding anatomical joints making up the medial column of the foot. The aim of this study was to develop a technique which allows for a quantification of the in-vivo sagittal mobility of the joints of the medial foot column during the roll-over process under full weight bearing. Methods Mobility of first ray bones was investigated by dynamic distortion-free fluoroscopy (25 frames/s) of 14 healthy volunteers and 8 patients with manifested clinical instability of the first ray. A CAD-based evaluation method allowed the determination of mobility and relative displacements and rotations of the first ray bones within the sagittal plane during the stance phase of gait. Results Total flexion of the first ray was found to be 13.63 (SD 6.14) mm with the healthy volunteers and 13.06 (SD 8.01) mm with the patients (resolution: 0.245 mm/pixel). The dorsiflexion angle was 5.27 (SD 2.34) degrees in the healthy volunteers and increased to 5.56 (SD 3.37) degrees in the patients. Maximum rotations were found at the naviculo-cuneiform joints and least at the first tarso-metatarsal joint level in both groups. Conclusions Dynamic fluoroscopic assessment has been shown to be a valuable tool for characterisation of the kinematics of the joints of the medial foot column during gait. A significant difference in first ray flexion and angular rotation between the patients and healthy volunteers however could not be found.