Search

Zn-Al-Cu alloys are predominantly used due to their tribological properties. One of the crucial issues related to the use of Zn-Al alloys is their dimensional instability. Partial replacement of copper with titanium greatly contributes to the reduction of the dimensional instability issue. The study involved the ZnAl40Cu1.5Ti1.5 alloy. In this work, microstructure and wear properties of ZnAl40Cu1.5Ti1.5 alloy were studied in both as-cast and heat treated conditions. The heat treatment was performed by solution treatment at a temperature of 385°C for 24 hours, quenching in cold water and artificial aging at 125°C for 3 hours. The hardness tests enabled to specify the optimum ageing time span, which amounts to 3 hours. Wear tests indicated that the ZnAl40Cu1.5Ti1.5 alloy is characterized with high wear resistance. It was also observed that the applied heat treatment increases the wear resistance of the experimental alloy.

The influence of solution heat treatment at 385°C over 10 h with cooling in water on the structure, hardness and strength of the ZnAl22Cu3 eutectoid alloy is presented in the paper. The eutectoid ZnAl22Cu3 alloy is characterized by a dendritic structure. Dendrites are composed of a supersaturated solid solution of Al in Zn. In the interdendritic spaces a eutectoid mixture is present, with an absence of the ε (CuZn4) phase. Solution heat treatment of the ZnAl22Cu3 alloy causes the occurrence of precipitates rich in Zn and Cu, possibly ε phase. Solution heat treatment at 385°C initially causes a significant decrease of the alloy hardness, although longer solution heat treatment causes a significant increase of the hardness as compared to the as-cast alloy.

Zn-Al-Cu alloys are used primarily because of their tribological properties as an alternative material for bronze, cast iron and aluminum alloy bearings and as a construction material. Particularly interesting are high aluminum zinc alloys. Monoeutectic zinc and aluminum alloys are characterized by the highest hardness, tensile strength and wear resistance of all of the zinc alloys. A significant problem with the use of the Zn-Al-Cu alloys is their insufficient resistance to electrochemical corrosion. Properties of Zn-Al-Cu alloys can be improved by heat treatment. The purpose of examination was to determine the effect of heat treatment (aging at various temperatures) on the microstructure and corrosion resistance of the ZnAl40Cu3 alloy. The scope of the examination included: structural examinations, determination of hardness using Brinell’s method and corrosion resistance examinations. Ageing at higher temperatures causes a creation of areas where is an eutectoid mixture. The study showed that ageing causes a decrease in hardness of ZnAl40Cu3 alloy. This decrease is even greater, when the temperature of ageing is lower. The studies have shown a significant influence of ageing on the corrosion resistance of the alloy ZnAl40Cu3. Maximum corrosion resistance were characterized by the sample after ageing at higher temperatures.

Zn-Al alloys are mainly used due to their high tribological and damping properties. A very important issue is determination of the hardness of the phases present in the Zn-Al-Cu alloys. Unfortunately, in literature there is lack of studies on the hardness of the phases present in the alloys Zn-Al-Cu. The aim of this research was to determine the hardness of the phases present in the ZnAl22Cu3Si and ZnAl40Cu3Si alloys. The scope of the research included examination of the structure, chemical composition of selected micro-regions and hardness of phases present in the examined alloys. The research carried out has shown, that CuZn4 phase is characterized by a similar hardness as the hardness of the interdendritic areas. The phases present in the structure of ZnAl40Cu3 and ZnAl22Cu3 alloys after soaking at the temperature of 185 °C are characterized by lower hardness than the phase present in the structure of the as-cast alloys.

The aim of this paper was to determine the effect of heat treatment for the corrosion resistance of the ZnAl40Ti2Cu alloy under "acid rain" conditions. ZnAl40TiCu alloy after supersaturation and after supersaturation and aging was studied. Potentiodynamic studies, potentiostatic studies and studies on structure of the alloy top layer of samples after corrosion tests were carried out. These investigations indicated a significant influence of heat treatment on corrosion resistance of the ZnAl40Ti2Cu alloy. The highest increase in corrosion resistance comparing to the alloy in the as-cast condition may be obtained by supersaturation. A significant influence of the aging temperature and time on corrosion resistance was proved. [ABSTRACT FROM AUTHOR]

Zn-Al-Cu alloys are characterised by very good tribological properties: high resistances to abrasive wear and adhesive wear, resistance to dry friction, low friction coefficient. Important disadvantages of Zn-Al alloys include, among others low structural and dimensional instability in as-cast stage and during long-period after pouring into moulds. Studies carried out in recent years confirm the problem of dimensional instability of Zn-Al-Cu alloys may be reduced by replace copper partially with titanium. The goal of the studies carried out was to define the influence of heat treatment on the microstructure and phase composition of ZnAl40Cu(1-2)Ti(1-2) alloys. The scope of the investigations included analysis of the phase composition, tests using a scanning electron microscope and a scanning transmission electron microscope, and X-ray microanalysis. The studies carried out indicate a presence of the e-CuZn5 and Ti2ZnAl5, AlxCuyTiz phases in the ZnAl40Cu(1-2)Ti(1-2) alloys. [ABSTRACT FROM AUTHOR]

Macromastia can cause various clinical symptoms, such as low back and shoulder pain as well as sacro-iliac disorders. Because of these symptoms, some women consider breast reduction surgery. So far there does not exist a clear correlation between breast size and back pain. Purpose of this study was to evaluate if increasing breast size has a measurable effect on women's posture using radiation free surface topography.A total of 100 women were grouped according to their breast cup size into four groups (Cup Size: A, B, C, D). All female subjects were measured with a surface topography system, and their spinal posture and pelvic position were analysed accordingly.Our results showed that cup size affects kyphotic angle (p = 0.027) and surface rotation (p = 0.039) significantly. Kyphotic angle increased with cup size. Multiple linear regression analysis, however, revealed that the body mass index has the greatest influence on woman's posture, showing significant correlation to kyphotic and lordotic angle (p < 0.01), as to trunk (p < 0.01) and pelvic inclination (p = 0.02).This is the first study that evaluates the influence of increasing breast size on posture using surface topography. The results match with previous studies using different measuring techniques. However, the great influence of BMI on posture is also confirmed. Therefore, in clinical practice these factors should be taken into account and be approached. Surface topography seems to be a promising tool to further investigate the influence of breast size on posture.Level of Evidence IV This journal requires that authors assign a level of evidence to each article. For a full description of these Evidence-Based Medicine ratings, please refer to the Table of Contents or the online Instructions to Authors www.springer.com/00266 ., (© 2022. The Author(s).)

Background: Recent studies have suggested that psychological factors are important components of a successful return to sports (RTS) after anterior cruciate ligament reconstruction (ACLR). The purpose of this study was to survey physicians with respect to their criteria used to determine readiness to RTS after ACLR and to understand the significance of psychological factors on RTS., Methods: A survey was designed to understand the practices of clinicians managing rehabilitation after ACLR, consisting of 25 questions divided into 3 different sections, including one section about psychological scores and factors affecting RTS. The survey was delivered to three North American organizations for orthopedic sports medicine., Results: The total number of respondents was 113. Of the respondents, 95% considered psychological tests at least "somewhat important" (33% "important", 23% selected "very important"). Routine use of psychological tests in practice was only reported by 35% of respondents. The ACL-Return to Sport after Injury Scale was the most frequently used psychological test (23%). Fear of reinjury was considered the most common patient-cited psychological factor affecting RTS. Psychological factors ranked 8th out of 9 outcomes measures in determining readiness to RTS., Conclusion: This study demonstrates a discrepancy between the importance of psychological tests and the frequency of use in practice. Additional education on this topic, web-based applications, and a multidisciplinary approach may increase the usage of psychological tests to determine RTS after ACLR., Competing Interests: The authors declare that they have no conflict of interest., (Thieme. All rights reserved.)

Consideration of the individual carpal bone characteristics of the wrist plays a key role in well-functioning biomedical devices and successful surgical procedures. Although geometric differences and individual bone sizes have been analyzed in the literature, detailed morphologic descriptions and correlations covering the entire wrist reported in a clinical context are lacking. This study aimed to perform a comprehensive and automatic analysis of the wrist morphology using the freely available "Open Source Carpal Database" (OSCD). We quantified the size of each of the individual carpal bones and their combination. These sizes were extracted in n = 117 datasets of the wrist of the OSCD in anatomical directions and analyzed using descriptive statics and correlation analysis to investigate the morphological characteristics under sex-specific aspects and to provide regression plots and equations to predict individual carpal bone sizes from the proximal and distal row dimensions. The correlations in the proximal row were higher compared to the distal row. We established comprehensive size correlations and size rations and found that there exist statistical differences between sex, particularly of the scaphoid. The regression plots and equations we provided will assist surgeons in a more accurate preoperative morphological evaluation for therapy planning and may be used for future anatomically inspired orthopedic biomedical device designs.

Tears of the anterior cruciate ligament (ACL) negatively impact the stability and kinematics of the knee. Interference screws (ISs) are used for graft fixation in ACL reconstruction and provide sufficient fixation strength to withstand the patients' activities during the graft-to-bone integration process. Magnesium is a novel material used to manufacture IS given its strength and bioabsorbability. In previous studies, the selected magnesium IS design showed a better fixation performance in comparison to the conventional IS design due to its shape design and surface condition. In this study, bioabsorbable magnesium ISs were tested for their insertion (insertion torque and a number of turns to implement the IS) and fixation performance (pull-out and dynamic test). To obtain a reliable initial assessment of IS performance, ISs were implanted in 15 per cubic foot (PCF) Sawbones polyurethane foam blocks, Sawbones biomechanical tibia models with 17 PCF foam cores, and human cadaveric tibiae. Porcine tendons were used in the foam block pull-out test, and nylon ropes were used in all other test setups to prevent influences of the ligament graft material itself. In the pull-out test, the graft was subjected to tensile stress at a rate of 6 mm/min. For the dynamic test, 1000 cycles between 0 and 200 N were performed, followed by a final pull-out test. After each test, the tunnel widening pattern was observed by measuring the aspect ratio of the tunnel at the insertion site. The insertion torque lies within the normal insertion torque of the ISs as well as the average ligament tension before the insertion. In the foam block setup, the nylon rope showed a higher pull-out force than the porcine tendon. The comparison of each setup using nylon rope for both pull-out and pull-out after the dynamic test showed no significant difference between the foam block and cadaver setup. However, all tibia model setup shows unexpectedly high pull-out force due to the influence of its cortical layer. There were no statistically significant differences in tunnel widening between foam block-porcine tendon and foam block-nylon rope constructs. The pull-out resistance of magnesium ISs falls within the typical ACL tension range during daily activities. Even though the test results of the magnesium ISs are different in each bone material, the magnesium IS shows adequate fixation ability and workability during insertion without material failure., (© 2023. The Author(s).)

An anterior cruciate ligament (ACL) reconstruction is a common treatment for patients with ACL rupture that aims to regain pre-injury knee stability and kinematics. During the ACL reconstruction, one method to fix the graft is the use of an interference screw (IS). The IS should provide initial stability and secure the graft during the healing period. In recent years, magnesium has emerged as an alternative material to permanent metal and polymer ISs. In addition, differences in designs, such as the shape of the IS, can influence the fixation performance of the IS. Therefore, in this biomechanical experiment, two different screw designs with two ligament materials were compared in an insertion and a pull-out test at a rate of 1 mm/s. The screw designs were a conventional polymer screw and a magnesium screw. Porcine tendon and nylon rope were used as ligament materials. All tests were performed in polyurethane foam blocks with 15 PCF density (Synbone AG, Switzerland). As a result, both screw designs required an insertion torque of less than 3 Nm. There was a significant difference between the porcine and nylon rope in pull-out tests for each screw design. The magnesium screw had the highest pull-out force at 412.14 ± 50.00 N for porcine tendon and 707.38 ± 21.81 N for nylon rope. There were no significant differences in tunnel widening (narrow-wide ratio) between each ligament material. The magnesium screw showed the lowest narrow-wide tunnel ratio, implying a better ability to compress the graft to the tunnel. In conclusion, a more optimized magnesium IS design resulted in better graft fixation and an improved ACL reconstruction outcome.

Aneurysmal bone cyst (ABC) is a benign osseus lesion with a high pathologic fracture risk. The described treatment options are varied and inconsistent. For successful treatment results, it is essential to prevent recurrence and sufficiently stabilise the weakened bone. Lesions close to the growth plates, especially in the femoral neck region, are challenging to stabilise in children. In this study, 27 clinics, including 11 sarcoma centres, 15 paediatric orthopaedic clinics, and one sarcoma/paediatric orthopaedic centre, were surveyed and asked about their treatment approaches for an exemplary case of ABC in the femoral neck causing a pathological fracture in a 20-month-old infant, with a response rate of 81%. The heterogeneity of treatment options described in the literature is consistent with the survey results. The most favoured approach was curettage, defect filling of any kind, and surgical stabilisation. However, the lesion stabilisation option introduced in this paper, which involves the use of transphyseal screws, was not mentioned in the survey and has not been reported in the literature. Contrary to the existing concepts, our technique offers high stability without significant growth restriction. Transphyseal screws are also suitable for the treatment of femoral neck fractures of other aetiologies in children.

Background: The surgical treatment of inferior patellar pole fractures can be a challenge, especially in geriatric patients, who are particularly frequently affected by osteoporosis. The objective of this biomechanical study was to compare the performance of suture anchor and transosseous suture fixation in fractures of the inferior patellar pole in context of bone mineral density., Methods: Twelve fresh-frozen human cadaveric knees received a transverse osteotomy, simulating an AO/OTA 34C1.3 inferior pole fracture of the patella. These fractures were fixated with either suture anchors (SA; Corkscrew ® FT 4.5 mm) or transosseous suture (TS; #2 FiberWire ® ). Cyclic loading tests were performed by pulling the quadriceps tendon against gravity from 90° flexion to almost full extension (5°) for 1000 cycles. Motion and fracture gap displacement were tracked until failure occurred. Subsequently, loading to failure tests followed. Differences between groups were compared using unpaired t-tests, and correlations were calculated with Pearson's correlation coefficient., Results: The suture anchor group showed significantly fewer cycles to failure than the transosseous suture group (SA: 539.0 ± 465.6 cycles, TS: 1000 ± 0 cycles, P = 0.04). Bone mineral density correlated positively with cycles to failure in the suture anchor group (Pearson's r = 0.60, P = 0.02). No differences in fracture gap displacement could be proven after 100 cycles (SA: 4.1 ± 2.6 mm, TS: 6.5 ± 2.6 mm, P = 0.19); 500 cycles (SA: 6.4 ± 6.1 mm, TS: 9.6 ± 3.8 mm, P = 0.39); and 1000 cycles (SA: 4.0 ± 0.4 mm, TS: 11.0 ± 4.5 mm, P = 0.08). Furthermore, the mean destructive load to failure in the suture anchor group was also significantly lower than in the transosseous suture group (SA: 422.4 ± 212.2 N, TS: 825.7 ± 189.3 N, P = 0.04)., Conclusions: Suture anchors may be a viable alternative to transosseous suture in younger patients for clinical advantages, but in osteoporotic bone, the more stable osteosynthesis with transosseous suture continues to prove superior. Therefore, trauma surgeons might consider the use of transosseous suture in elderly patients, especially in those presenting with low bone mineral density values., (© 2022. The Author(s).)

Introduction: Dislocations of the hip joint are a common and clinically relevant complication following total hip arthroplasty (THA). Hip-abduction braces are currently used following operative or non-operative treatment of THA dislocations to prevent re-dislocations. However, the clinical and biomechanical effectiveness of such braces is still controversial., Material and Methods: A total of 30 volunteers were measured during standing and during sitting up and down from a chair task wearing a hip brace set at 70°, 90° or no hip flexion limitation. Range of motion of the hip joint was measured in all directions by an inertial sensor system. Further it has been evaluated if the range of motion would be reduced by the additional use of an arthrodesis cushion., Results: The use of a hip brace set up with flexion limitation did reduce hip ROM in all directions significantly compared to unhinged brace (p < 0.001-0.035). Performing the "sit down and stand-up task" the brace set up at 70° flexion limitation did reduce maximum hip flexion significantly (p = 0.008). However, in most cases the measured hip flexion angles were greater than the settings of the hip brace should have allowed. The additional use of a cushion can further limit hip motion while sitting up and down from a chair., Conclusion: This study has demonstrated that hip-abduction braces reduce hip range of motion. However, we also found that to achieve a flexion limitation of the hip to 90°, the hip brace should be set at a 70° hip flexion limitation., (© 2021. The Author(s).)

In this study, three different musculoskeletal modeling approaches were compared to each other. The objective was to show the possibilities in the case of a simple mechanical model of the wrist, using a simple multi-body-simulation (MBS) model, and using a more complex and patient-specific adaptable wrist joint MBS model. Musculoskeletal modeling could be a useful alternative, which can be practiced as a non-invasive approach to investigate body motion and internal loads in a wide range of conditions. The goal of this study was the introduction of computer-based modelling of the physiological wrist with (MBS-) models focused on the muscle and joint forces acting on the wrist.

Background: Leg length inequalities are a frequent condition in every population. It is common clinical practice to consider LLIs of 2 cm and more as relevant and to treat those. However, the amount of LLIs that need treatment is not clearly defined in literature and the effect of real LLIs on the musculoskeletal system above and below 2 cm have not been studied biomechanically before., Methods: By using surface topography, we evaluated 32 patients (10 females, 22 male) with real LLIs of ≥ 2 cm (mean: 2.72 cm; n = 10) and compared their pelvic position and spinal posture to patients with LLIs < 2 cm (mean: 1.24 cm; n = 22) while standing and walking. All patients were measured with a surface topography system during standing and while walking on a treadmill. To compare patient groups, we used Student t-tests for independent samples., Results: Pelvic obliquity was significantly higher in patients with LLI ≥ 2 cm during the standing trial (p = 0.045) and during the midstance phase of the longer leg (p = 0.023) while walking. Further measurements did not reveal any significant differences (p = 0.06-0.706)., Conclusions: The results of our study suggest that relevant LLIs of ≥ 2 cm mostly affect pelvic obliquity and do not lead to significant alterations in the spinal posture during a standing trial. Additionally, we demonstrated that LLIs are better compensated when walking, showing almost no significant differences in pelvic and spinal posture between patients with LLIs smaller and greater than 2 cm. This study shows that LLIs ≥ 2 cm can still be compensated; however, we do not know if the compensation mechanisms may lead to long-term clinical pathologies., (© 2022. The Author(s).)

Background: Stair climbing is a complex and demanding daily activity with increased physical loads. Therefore, analyzing stair climbing abilities is a frequently used diagnostic tool. Leg length inequalities (LLIs) are a common condition in the population, with individual consequences like lower back pain, scoliosis, and osteoarthritis. Despite its high prevalence, the necessary treatment, for mild LLIs, is still controversial. Previously, the focus was to analyze the effects of LLIs during static standing and walking. To create a holistic view on the dynamic effects of LLIs, and since climbing stairs produces a similar biomechanical imbalance as LLIs, the compensation mechanics during stair climbing are of special interest., Research Question: What are the biomechanical compensation mechanisms of (simulated) LLIs during ascending and descending stairs?, Methods: Thirty-five healthy participants were measured with the inertial measurement system MyoMotion during stair climbing with simulated LLIs of 0-3 cm. The maximum estimated lower limb joint angles of the long and short leg were analyzed with statistically repeated measurement models., Results: The long leg showed significantly increased hip and knee flexion, while the short leg showed decreased hip and knee flexion, decreased dorsiflexion, and significantly increased plantarflexion. Different mechanisms were found in the case of 1 cm LLI when compared to greater LLIs. In the former, increased hip and knee flexion in the short leg accompanied by increased dorsiflexion in the long leg was observed. In the latter, the dorsiflexion of the long leg was reduced., Significance: Except for the reduced dorsiflexion of the long leg (LLI >1 cm), during stair climbing compared compensation mechanisms as during walking were presented, with the long leg functionally shortened and the short leg lengthened. Although the feet were already on different levels, during stair climbing with the step-over-step technique, significant compensation mechanisms were found as a consequence of LLIs., (Copyright © 2021 Elsevier B.V. All rights reserved.)

Background: Biomarkers of left atrial (LA) overload are considered factors affecting the efficacy of atrial fibrillation (AF) treatment. Increasing obesity rates contribute to a growing number of obese patients qualified for electrical cardioversion (CVE).Biomarkers of left atrial (LA) overload are considered as factors influencing efficacy of atrial fibrillation (AF) treatment. The increasing rate of obesity contributes to obese patients constituting a significant group of subjects qualified to electrical cardioversion (CVE)., Aims: The aim of the study was to evaluate serum concentrations of biomarkers of LA overload and their impact on the efficacy of CVE., Methods: A total of 82 patients with persistent AF who underwent successful CVE were prospectively enrolled in the study. The study population was divided into the obese group (OG) and the nonobese group (NOG). The serum levels of the following biomarkers were measured on the day of admission and at follow‑up: high‑sensitivity C‑reactive protein (hs‑CRP), N‑terminal pro‑B‑type natriuretic peptide, copeptin, galectin 3, growth differentiation factor 15 (GDF‑15), and renalase., Results: Baseline and follow‑up hs‑CRP levels were increased in the OG compared with the NOG. Four‑week CVE efficacy was 38.8% in the OG and 60.6% in the NOG. Time of the observation, allocation to the groups, and CVE outcomes showed no associations with most LA biomarkers during follow‑up. Baseline concentrations of 2 biomarkers of LA overload were associated with clinical characteristics of the study group, that is, log10 serum GDF‑15 and log10 serum renalase levels correlated positively with the CHA2DS2‑VASc score., Conclusions: Although obesity modifies the long‑term efficacy of CVE, the OG and NOG did not differ significantly in most biomarkers of LA overload, except hs‑CRP. The efficacy of CVE seems to be independent of the levels of biomarkers. A favorable procedure outcome did not affect their blood concentrations.

Background: Smartphones have become increasingly more popular and complicated tasks can be performed with these devices. However, the increasing use is associated with shoulder and neck pain, as well as with psychological addiction., Research Question: Do different smartphone tasks lead to changes in spinal posture and pelvic position? Is there a relationship between smartphone addiction and changes in posture?, Methods: A cross-sectional study including 50 participants was performed. Test subjects completed the Smartphone Addiction Scale and the SF-36 health questionnaire. Subjects spinal posture and pelvic position during different smartphone tasks were measured through a surface topography system. The different tasks were: standing in an upright position, simulating a phone call, texting with one or two hands during standing or while walking on a treadmill. Paired T-tests and ANOVA tests were performed to evaluate differences. The Kendall rank test was used to investigate the association between clinical scores and changes in spinal posture., Results: All smartphone tasks lead to a significant increase in thoracic kyphosis and trunk inclination during standing and while walking. A significant increased lumbar lordosis was also found. Texting with one or two hands correlated with increased surface rotation. No associations between smartphone addiction and changes of the spinal posture were reported., Significance: This represents the first surface topography study that investigated the influence of different smartphone tasks on the spinal posture and pelvic position during standing and while walking. With the results of this study we demonstrated that smartphone use leads to significant changes of sagittal and frontal spine parameters. Further research should focus on the evaluation of possible detrimental effects of long-term smartphone use on the spinal posture and on the development of preventive measures., (Copyright © 2021 Elsevier B.V. All rights reserved.)

Agriculture is an important sector of the economy, but this industry consumes significant amounts of water, which is a precious and limited natural resource. Irrigation techniques and efforts to mitigate water usage influence the growth, survival, and yield of crops. However, superabsorbent polymers in combination with fertilizers can be employed to obtain sustained release of nutrients and improved water retention capacity of the soil. Despite significant recent progress in this area involving synthetic polyacrylate hydrogels, there are no industrially applicable solutions exhibiting similar performance using natural biopolymers or synthetic polymers enriched with natural components. This review focuses on biodegradable chitosan-based hydrogels (both natural and semi-synthetic), and discusses their potential agricultural and horticultural applications. The methods for synthesizing hydrogels via physical or chemical crosslinking, and the resulting functional properties of recently reported hydrogels, such as water retention and release of active ingredients, are presented herein.

Background: Until recently, rasterstereographic analysis of the spine was limited to static measurements. However, understanding and evaluating the motion of the spine under dynamic conditions is an important factor in the diagnosis and treatment of spinal pathologies. The aim of this study was to study the spinal posture and pelvic position under dynamic conditions and compare it to static measurements using a dynamic rasterstereographic system., Methods: A total of 121 healthy volunteers (56 females; 65 males) were included in this observational study. The parameters trunk inclination, trunk imbalance, pelvic obliquity, kyphotic angle, lordotic angle, surface rotation, and lateral deviation were studied and compared under static and dynamic (1, 2, 4, 5 km/h) conditions using the system "Formetric 4D Motion®" (DIERS International GmbH, Germany)., Results: Female volunteers had a higher lordotic angle than males under static conditions (p < 0.001). Trunk inclination (5.31° vs. 6.74°), vertebral kyphotic angle (42.53° vs. 39, 59°), and surface rotation (3.35° vs. 3.81°) increase under dynamic conditions (p < 0.001). Trunk inclination and lordotic angle both show significant changes during walking compared to static conditions (p < 0.001)., Conclusion: The spinal posture differs between females and males during standing and during walking. Rasterstereography is a valuable tool for the dynamic evaluation of spinal posture and pelvic position, which can also be used to quantify motion in the spine and therefore it has the potential to improve the understanding and treatment of spinal pathologies., Trial Registration: Retrospectively registered.

Background: Apart from eccentric exercises (EE), isometric exercises (ISO) might be a treatment option for Achilles tendinopathy. Shear wave elastography (SWE) provides information for diagnosis and for monitoring tissue elasticity, which is altered in symptomatic tendons., Hypothesis: Isometric exercises will have a beneficial effect on patients' outcome scores. Based on SWE, insertional and midportion tendon parts will differ in their elastic properties according to current symptoms., Study Design: Randomized clinical trial., Level of Evidence: Level 2., Methods: Group 1 (EE; n = 20; 12 males, 8 females; mean age, 52 ± 8.98 years) and group 2 (EE + ISO; n = 22; 15 males, 7 females; mean age, 47 ± 15.11 years) performed exercises for 3 months. Measurement points were before exercises were initiated as well as after 1 and 3 months using the Victorian Institute of Sports Assessment-Achilles (VISA-A) score, American Orthopaedic Foot & Ankle Society score, and SWE (insertion and midportion)., Results: Both groups improved significantly, but there were no significant interindividual differences (VISA-A; P = 0.362) between group 1 (n = 15; +15 VISA-A) and group 2 (n = 15; +15 VISA-A). The symptomatic insertion (symptomatic, 136.89 kPa; asymptomatic, 174.68 kPa; P = 0.045) and the symptomatic midportion of the Achilles tendon (symptomatic, 184.40 kPa; asymptomatic, 215.41 kPa; P = 0.039) had significantly lower Young modulus compared with the asymptomatic tendons. The midportion location had significantly higher Young modulus than the insertional part of the tendon ( P = 0.005)., Conclusion: Isometric exercises do not have additional benefit when combined with eccentric exercises, as assessed over a 3-month intervention period. SWE is able to distinguish between insertional and midportion tendon parts in a symptomatic and asymptomatic state., Clinical Relevance: The present study shows no additional effect of ISO when added to baseline EE in treating Achilles tendinopathy. Different elastic properties of the insertional and midportion tendon have to be taken into consideration when rating a tendon as pathologic.

Background: Leg length inequalities (LLIs) are a common finding in patients with a total hip arthroplasty (THA). Therefore, we compared the effects of simulated LLIs in patients with total hip arthroplasty (THA) with a matched control group., Research Question: Do LLIs lead to different effects on the musculoskeletal apparatus of patients with a THA then in a control group?, Methods: In 99 patients with a THA the effects of simulated LLIs were compared to a matched control group of 101 subjects without a hip arthroplasty. First, we compared methods for LLI quantification (tape measurements, pelvic x- ray and rasterstereography). Second, the effects of simulated LLIs on the spine and pelvis were evaluated in both groups using surface topography. LLIs of 5, 10, 15, 20 and 30 mm were simulated on both sides with a simulation platform. The changes of pelvic position (pelvic obliquity & pelvic torsion) and the effects on spinal posture (surface rotation & lateral deviation) were measured and analysed using a surface topography system., Results: Mean LLI measured with a tape was 0.9 mm (SD +/- 14.8). Mean pelvic obliquity measured on x-rays was 1.2 mm (SD +/- 11.6) and with surface topography 0.9 mm (SD +/- 7.9). Simulated LLIs resulted in significant changes of pelvic position and spinal posture in the patient and control group. Interestingly, our study showed that simulated LLIs lead to greater changes in pelvic position (p<0.05) in patients with a THA., Significance: This is the first study to demonstrate that LLIs might have a greater impact on the pelvic position of THA patients than in native hips, which could indicate that LLIs do need to be compensated differently in patients with THA than in patients without a THA., Competing Interests: The authors have declared that no competing interests exist.