Search

Statement of problem. Polyetheretherketone (PEEK) has been advocated to replace metal components in dentistry. Although PEEK is a high-performance polymer with a white color, adequate biological response, and resistance to fracture, data to support PEEK as an alternative material for implant abutments are lacking. Purpose. The purpose of this in vitro study was to assess the mechanical and functional properties of PEEK implant abutments as a nonmetallic alternative to titanium abutments, which presents esthetic limitations and greater difficulty to customize clinically. Material and methods. Implant abutments manufactured by using PEEK (n=24) or titanium grade 5 (n=24) were attached to MIS Implants type M4 3.75×16 mm with an internal screw tightened to 25 Ncm. Screw loosening and microleakage was assessed by submersion in a 2% methylene blue solution for 48 hours at 37 C. Both groups were compared with and without applying dynamic loading; fatigue testing was performed following the International Organization for Standardization (ISO) 14801:2016 standard. All specimens were observed under a stereomicroscope at ×8 magnification. Statistically significant differences among the PEEK and titanium implant abutments were tested with 2-factor ANOVA and the chi-square analysis for nonpaired and paired data, respectively (a=.05). Results. The implant abutments made of titanium were better in all mechanical tests. The torque loss of titanium abutments was approximately 10%, while PEEK showed a significantly higher (P

The COVID-19 pandemic has caused a high demand for respiratory protection among health care workers in hospitals, especially surgical N95 filtering facepiece respirators (FFRs). To aid in alleviating that demand, a survey of commercially-available filter media was conducted to determine whether any could serve as a substitute for an N95 FFR while held in a 3D-printed mask (Stopgap Surgical Face Mask from the NIH 3D Print Exchange). Fourteen filter media types and eight combinations were evaluated for filtration efficiency, breathing resistance (pressure drop), and liquid penetration. Additional testing was conducted to evaluate two filter media disinfection methods in the event that the filters were reused in a hospital setting. Efficiency testing was conducted in accordance with the procedures established for approving an N95 FFR. One apparatus used a filter-holding device and another apparatus employed a manikin head to which the 3D-printed mask could be sealed. The filter media and combinations exhibited collection efficiencies varied between 3.9% to 98.8% when tested with a face velocity comparable to that of a standard N95 FFR at the 85 L min(−1) used in the approval procedure. Breathing resistance varied between 10.8 to >637 Pa (1.1 to > 65 mm H(2)O). When applied to the 3D-printed mask efficiency decreased by an average of 13% and breathing resistance increased 4-fold as a result of the smaller surface area of the filter media when held in that mask compared to that of an N95 FFR. Disinfection by dry heat, even after 25 cycles, did not significantly affect filter efficiency and reduced viral infectivity by > 99.9%. However, 10 cycles of 59% vaporized H(2)O(2) significantly (p < 0.001) reduced filter efficiency of the media tested. Several commercially-available filter media were found to be potential replacements for the media used to construct the typical cup-like N95 FFR. However, their use in the 3D-printed mask demonstrated reduced efficiency and increased breathing resistance at 85 L min(−1).

A lack of primary stability and osteointegration in metallic implants may result in implant loosening and failure. Adding porosity to metallic implants reduces the stress shielding effect and improves implant performance, allowing the surrounding bone tissue to grow into the scaffold. However, a bioactive surface is needed to stimulate implant osteointegration and improve mechanical stability. In this study, porous titanium implants were produced via powder sintering to create different porous diameters and open interconnectivity. Two strategies were used to generate a bioactive surface on the metallic foams: (1) an inorganic alkali thermochemical treatment, (2) grafting a cell adhesive tripeptide (RGD). RGD peptides exhibit an affinity for integrins expressed by osteoblasts, and have been reported to improve osteoblast adhesion, whereas the thermochemical treatment is known to improve titanium implant osseointegration upon implantation. Bioactivated scaffolds and control samples were implanted into the tibiae of rabbits to analyze the effect of these two strategies in vivo regarding bone tissue regeneration through interconnected porosity. Histomorphometric evaluation was performed at 4 and 12 weeks after implantation. Bone-to-implant contact (BIC) and bone in-growth and on-growth were evaluated in different regions of interest (ROIs) inside and outside the implant. The results of this study show that after a long-term postoperative period, the RGD-coated samples presented higher quantification values of quantified newly formed bone tissue in the implant’s outer area. However, the total analyzed bone in-growth was observed to be slightly greater in the scaffolds treated with alkali thermochemical treatment. These results suggest that both strategies contribute to enhancing porous metallic implant stability and osteointegration, and a combination of both strategies might be worth pursuing. info:eu-repo/semantics/publishedVersion

Diamond-like carbon (DLC) coatings have been extensively studied over the last two decades in the field of materials engineering. The addition of effective bactericidal agents like silver suggests the potential application of silver-doped DLC coatings in the biomedical sector. In this paper, DLC coatings containing about 2 at. % Ag were grown on CoCrMo substrates by pulsed filtered cathodic arc co-deposition using pure graphite and silver targets. Morphology, structure and chemical composition of the coatings were characterized by SEM, XPS, XRD, Raman and HRTEM. Wettability and surface free energy were also measured. Mechanical properties were analyzed by means of nanoindentation and Rockwell-C adhesion tests. Corrosion resistance of coated and uncoated samples was determined by potentio-dynamic polarization tests in Hank's solution. Cytotoxicity and antibacterial activity against S. aureus and P. aeruginosa were also studied. For comparative purposes, nitrogen-doped DLC coatings obtained by RF magnetron sputtering were also prepared and characterized. Well-adhered and corrosion resistant Ag-DLC nanostructured coatings of up to 1.5 µm thick and 21 GPa in hardness were obtained. The doping concentration of silver studied in this work seems to be optimal for the preparation of non-cytotoxic coatings with a significant bactericidal activity. This work has been financed by the Ministry of the Economy, Industry and Competitiveness of Spain under the project BIOPLASMA (MAT2015-67103-C4).

Objectives: The aim of this research was to determine the osseointegration of two presentations of biphasic calcium phosphate (BCP) biomaterial&mdash, one untreated and another submitted to biofunctionalization with a TGF-&beta, 1 inhibitor peptide, P144, on dental alveolus. Materials and Methods: A synthetic bone graft was used, namely, (i) Maxresorb&reg, (Botiss Klockner) (n = 12), and (ii) Maxresorb&reg, (Botiss Klockner) biofunctionalized with P144 peptide (n = 12). Both bone grafts were implanted in the two hemimandibles of six beagle dogs in the same surgical time, immediately after tooth extraction. Two dogs were sacrificed 2, 4, and 8 weeks post implant insertion, respectively. The samples were submitted to histomorphometrical and histological analyses. For each sample, we quantified the new bone growth and the new bone formed around the biomaterial&rsquo, s granules. After optical microscopic histological evaluation, selected samples were studied using backscattered scanning electron microscopy (BS-SEM). Results: The biofunctionalization of the biomaterial&rsquo, s granules maintains a stable membranous bone formation throughout the experiment timeline, benefitting from the constant presence of vascular structures in the alveolar space, in a more active manner that in the control samples. Better results in the experimental groups were proven both by quantitative and qualitative analysis. Conclusions: Synthetic bone graft biofunctionalization results in slightly better quantitative parameters of the implant&rsquo, s osseointegration. The qualitative histological and ultramicroscopic analysis shows that biofunctionalization may shorten the healing period of dental biomaterials.

Although ceramic-on-ceramic (CoC) bearings have been shown to produce the smallest amount of wear volume in vitro as well as in vivo studies when used for total hip arthroplasties (THA), concerns about the failure of these bearing surfaces persist due to early failures observed after short postoperative time. In this study, an exhaustive analysis of the early failure occurred on the new generation of ceramic bearings, consisting of a composite alumina matrix-based material reinforced with yttria-stabilized tetragonal zirconia (Y-TZP) particles, chromium dioxide, and strontium crystals, was performed. For this study, 118 CoC bearings from 117 patients were revised. This article describes a group of mechanical failure CoC-bearing BIOLOX THA hip prosthesis patients without trauma history. The retrieved samples were observed under scanning electron microscopy (SEM), composition was analyzed with energy dispersive X-ray spectroscopy (EDX), and damaged surfaces were analyzed by grazing-incidence X-ray diffraction (GI-XRD) and white light interferometry. In the short term, CoC articulations provided similar mechanical behavior and functional outcome to those in XLPE cases. However, 5% more early mechanical failures cases were observed for the ceramic components. Although the fracture rate of third generation CoC couples is low, the present study shows the need to further improve the third generation of CoC-bearing couples for THA. Despite the improved wear compared to other materials, stress concentrators are sources of initial crack propagation, such as those found in the bore-trunnion areas. Moreover, in view of the evidence observed in this study, the chipping observed was due to the presence of monoclinic phase of the Y-TZP instead of tetragonal, which presents better mechanical properties. The results showed that total safety after receiving a THA is still a goal to be pursued. info:eu-repo/semantics/publishedVersion

Osteonecrosis of the femoral head (ONFH) is defined as a tissue disorder and successive subchondral bone collapse resulting from an ischemic process, which may progress to hip osteoarthritis. Cell therapy with multipotent bone marrow mesenchymal stromal cells (BM-MSC) of autologous origin appears to be safe and has shown regenerative potential in previous preclinical and clinical studies. The use of allogeneic cells is far more challenging, but may be a promising alternative to use of autologous cells. Moreover, an optimized dosage of cells from an allogeneic source is needed to obtain off-the-shelf tissue engineering products (TEPs). The purpose of this study was to evaluate the efficacy of a TEP composed of undifferentiated ex vivo expanded BM-MSC of allogeneic origin, combined with bone matrix particles in variable doses. A comparative analysis of TEP's bone regenerative properties against its autologous counterpart was performed in an early-stage ONFH preclinical model in mature sheep. Allogeneic BM-MSC groups demonstrated bone regeneration capacity in osteonecrotic lesions equivalent to autologous BM-MSC groups 6 weeks after treatment. Likewise, stimulation of bone regeneration by a low cell dose of 0.5 x 10(6) BM-MSC/cm(3) was equivalent to that of a high cell dose, 5 x 10(6) BM-MSC/cm(3). Neither local nor systemic immunological reactions nor tumorigenesis were reported, strengthening the safety profile of allogeneic BM-MSC therapy in this model. Our results suggest that low-dose allogeneic BM-MSC is sufficient to promote bone regeneration in femoral head osteonecrotic lesions, and should be considered in translation of new allogeneic cell-based TEPs to human clinics. Impact statement Cell therapy and tissue engineering hold promise as novel regenerative therapies for musculoskeletal diseases, and particularly in bone regeneration strategies. In this article, we report the evaluation of the efficacy of an allogeneic cell-based tissue engineering product (TEP) in an early-stage osteonecrosis of the femoral head preclinical model in skeletally mature sheep. Moreover, we demonstrate its bone regeneration capacity and safety in vivo and its equivalence to autologous counterparts. These findings have important implications for the translation of new allogeneic cell-based TEPs to human clinics.

One of the major problems faced by metallic implants is the high probability of bacterial infections, with significant consequences for the patient. In this work, a thermochemical treatment is proposed to obtain silver-doped calcium titanate coatings on the Ti surface to improve the bioactivity of porous 3D-printed Ti structures and simultaneously provide them with antibacterial properties. A complete characterization of the new coating, the study of the ion release and the analysis of its cytotoxicity were carried out together with evaluation of the natural apatite forming in simulated body fluid (SBF). Moreover, the antibacterial properties of the coatings were assessed against Pseudomona aeruginosa and Escherichia coli as gram-negative and Staphylococcus aureus and Staphylococcus epidermidis as gram-positive bacterial strains. Ag ions were integrated into the Ca titanate layer and Ag nanoparticles were formed within the entire 3D Ti surface. Ca and Ag ions were released from both porous and solid samples into the Hanks' solution for 48 h. The treated surfaces showed no cytotoxicity and an apatite layer precipitated on the entire porous surface when the samples were immersed in SBF. The release of Ag from the surface had a strong antibacterial effect and prevented bacterial adhesion and proliferation on the surface. Moreover, the nanostructured topography of the coating resulted also in a reduction of bacterial adhesion and proliferation, even in absence of Ag. In conclusion, the cost-effective approach here reported provided protection against the most predominant bacterial colonizers to the Ti porous implants, while maintaining their bioactivity.

The aim of this study was to evaluate the biomechanical behavior of Bone Level dental implants with four different neck designs in contact with cortical bone. Numerical simulations were performed using a Finite Element Method (FEM) based-model. In order to verify the FEM model, the in silico results were compared with the results obtained from histological analysis performed in an in vivo study with New Zealand rabbits. FEM was performed using a computerized 3D model of Bone Level dental implants inserted in the lower jaw bone with an applied axial load of 100 N. The analysis was performed using four different implant neck designs: even surfaced, screwed, three-ring design and four-ring design. Interface are of bone growth was evaluated by analyzing the Bone-Implant-Contact (BIC) parameter obtained from in vivo histological process and analyzed by Scanning Electron Microscopy (SEM). Bone Level implants were inserted in the rabbit tibia, placing two implants per tibia. The BIC was evaluated after three and six weeks of implantation. FEM studies showed that the three-ring design presented lower values of stress distribution compared to the other studied designs. The lower levels of mechanical stress were then correlated with the in vivo studies, showing that the three-ring design presented the highest BIC value after 3 and 6 weeks of implantation. In silico and in vivo results both concluded that the implants with three-ring neck design presented the best biomechanical and histological behavior in terms of new bone formation, enhanced mechanical stability and optimum osseointegration.

In this study, highly-interconnected porous titanium implants were produced by powder sintering with different porous diameters and open interconnectivity. The actual foams were produced using high cost technologies: Chemical Vapor Deposition (CVD), Physical Vapor Deposition (PVD), and spark plasma sintering, and the porosity and/or interconnection was not optimized. The aim was to generate a bioactive surface on foams using two different strategies, based on inorganic thermo-chemical treatment and organic coating by peptide adsorption, to enhance osseointegration. Porosity was produced using NaCl as a space holder and polyethyleneglicol as a binder phase. Static and fatigue tests were performed in order to determine mechanical behaviors. Surface bioactivation was performed using a thermo-chemical treatment or by chemical adsorption with peptides. Osteoblast-like cells were cultured and cytotoxicity was measured. Bioactivated scaffolds and a control were implanted in the tibiae of rabbits. Histomorphometric evaluation was performed at 4 weeks after implantation. Interconnected porosity was 53% with an average diameter of 210 &micro, m and an elastic modulus of around 1 GPa with good mechanical properties. The samples presented cell survival values close to 100% of viability. Newly formed bone was observed inside macropores, through interconnected porosity, and on the implant surface. Successful bone colonization of inner structure (40%) suggested good osteoconductive capability of the implant. Bioactivated foams showed better results than non-treated ones, suggesting both bioactivation strategies induce osteointegration capability.

Intervertebral implants should be designed with low load requirements, high friction coefficient and low elastic modulus in order to avoid the stress shielding effect on bone. Furthermore, the presence of a highly interconnected porous structure allows stimulating bone in-growth and enhancing implant-bone fixation. The aim of this study was to obtain bioactive porous titanium implants with highly interconnected pores with a total porosity of approximately 57¿%. Porous Titanium implants were produced by powder sintering route using the space holder technique with a binder phase and were then evaluated in an in vivo study. The size of the interconnection diameter between the macropores was about 210¿µm in order to guarantee bone in-growth through osteblastic cell penetration. Surface roughness and mechanical properties were analyzed. Stiffness was reduced as a result of the powder sintering technique which allowed the formation of a porous network. Compression and fatigue tests exhibited suitable properties in order to guarantee a proper compromise between mechanical properties and pore interconnectivity. Bioactivity treatment effect in novel sintered porous titanium materials was studied by thermo-chemical treatments and were compared with the same material that had undergone different bioactive treatments. Bioactive thermo-chemical treatment was confirmed by the presence of sodium titanates on the surface of the implants as well as inside the porous network. Raman spectroscopy results suggested that the identified titanate structures would enhance in vivo apatite formation by promoting ion exchange for the apatite formation process. In vivo results demonstrated that the bioactive titanium achieved over 75¿% tissue colonization compared to the 40¿% value for the untreated titanium.

Achieving high quality 3D-printed structures requires establishing the right printing conditions. Finding processing conditions that satisfy both the fabrication process and the final required scaffold properties is crucial. This work stresses the importance of studying the outcome of the plasticizing effect of PEG on PLA-based blends used for the fabrication of 3D-direct-printed scaffolds for tissue engineering applications. For this, PLA/PEG blends with 5, 10 and 20% (w/w) of PEG and PLA/PEG/bioactive CaP glass composites were processed in the form of 3D rapid prototyping scaffolds. Surface analysis and differential scanning calorimetry revealed a rearrangement of polymer chains and a topography, wettability and elastic modulus increase of the studied surfaces as PEG was incorporated. Moreover, addition of 10 and 20% PEG led to non-uniform 3D structures with lower mechanical properties. In vitro degradation studies showed that the inclusion of PEG significantly accelerated the degradation rate of the material. Results indicated that the presence of PEG not only improves PLA processing but also leads to relevant surface, geometrical and structural changes including modulation of the degradation rate of PLA-based 3D printed scaffolds. (C) 2014 Elsevier B.V. All rights reserved.