Search

—The article describes a method of generating bioactive alkali metal iodide aerosol particles with glycerin for inhalation; the particles have a diameter of d ≈ 0.03–3 µm and a mass productivity of m = 10–200 µg/s. A delivery device has been created.

The high-response diagnostic complex for remote control and analyses of droplets and vapors of mazut, oil, gasoline, kerosene, diesel fuel and liquefied natural gas in the clouds and turbulent aerosolflows in the atmosphere with volume up to 107 m3 is described.

Operation of a repetitively pulsed electric-discharge HF(DF) laser with an all-solid-state pump generator based on FID switches is demonstrated. The energy stored in the pump generator capacitors was 880 J at an open-circuit voltage of 240 kV and a discharge pulse repetition rate of 25 Hz. The specific energy extractions were 3.8 and 3.4 J L-1 for the HF and DF lasers, respectively. The possibilities of improving the output laser characteristics are discussed.

The characteristics of a Fe:ZnSe laser pumped by a single-pulse free-running Er : YAG laser and a repetitively pulsed HF laser are presented. An output energy of 4.9 J is achieved in the case of liquid-nitrogen cooling of the Fe2+:ZnSe active laser element longitudinally pumped by an Er:YAG laser with a pulse duration of 1 ms and an energy up to 15 J. The laser efficiency with respect to the absorbed energy is 47%. The output pulse energy at room temperature is 53 mJ. The decrease in the output energy is explained by a strong temperature dependence of the upper laser level lifetime and by pulsed heating of the active element. The temperature dependence of the upper laser level lifetime is used to determine the pump parameters needed to achieve high pulse energies at room temperature. Stable repetitively-pulsed operation of the Fe2+:ZnSe laser at room temperature with an average power of 2.4 W and a maximum pulse energy of 14 mJ is achieved upon pumping by a 1-s train of 100-ns HF laser pulses with a repetition rate of 200 Hz.

The application of thin ceramic films for the fabrication of MEMS devices enables the extension of their working temperature range up to 600°C, a decrease in heating power consumption, and a very considerable decrease in production cost of sensors and actuators based on this technology. These advantages are very important for the application of gas sensors under harsh environmental conditions, in autonomous and wireless sensor networks. The methods of the fabrication of MEMS platforms for metal oxide semiconductor and thermocatalytic gas sensors, fast thermometers, and flowmeters based on yttria stabilized zirconia (YSZ) and alumina membranes for gas sensors are described. Alumina membranes stable up to 800°C have thickness of about 12 microns and are produced by anodic oxidation of aluminum foil in diluted oxalic acid followed by high-temperature annealing. YSZ membrane with the same thickness is made by slip casting with consequent annealing under mechanic load. Platinum heaters are deposited onto the surface of the membrane by magnetron sputtering through metallic shadow mask. Perfect adhesion of platinum to ceramic material permits us to avoid the application of adhesive sub-layers, and, therefore, improves long-term stability of the heater at high temperature. The sensor chip has a shape of triangle cut by laser beam; the heater meander is located in the vertex of triangle. This approach simplifies the technology of the fabrication of the platform and decreases power necessary for the heating of the sensing layer up to working temperature of 400 – 600°C. It is shown that the application of such triangle shaped membranes permits a decrease in power consumption of the MEMS working at 450°C down to ~ 40 mW at continuous and down to < 1 mW at pulse heating of gas sensor with duty cycle of 1 %. Thermal response time of the microheater is of about 80 ms.

The methods of the fabrication of MEMS platforms based on yttria stabilized zirconia (YSZ) and alumina membranes for gas sensors used in harsh environmental conditions are described. It is shown that the application of such membranes permits a decrease in MEMS power consumption at 450°C down to ~75 mW at continuous and down to ~ 1 mW at pulse heating of gas sensor.