Search

Magnetohydrodynamics (MHD) can be used to model capillary discharge waveguides in laser-wakefield accelerators. However, the predictive capability of MHD can suffer due to poor microscopic closure models. Here, we study the impact of electron heating and thermal conduction on capillary waveguide performance as part of an effort to understand and quantify uncertainties in modeling and designing next-generation plasma accelerators. To do so, we perform two-dimensional high-resolution MHD simulations using an argon-filled capillary discharge waveguide with three different electron transport coefficients models. The models tested include (i) Davies et al. (ii) Spitzer, and (iii) Epperlein-Haines (EH). We found that the EH model overestimates the electron temperature inside the channel by over $20\%$ while predicting a lower azimuthal magnetic field. Moreover, the Spitzer model, often used in MHD simulations for plasma-based accelerators, predicts a significantly higher electron temperature than the other models suggest., Comment: 9 pages, 5 figures

Ultrafast lasers play an increasingly critical role in the generation, manipulation, and acceleration of electron beams for High Energy Physics applications. Laser plasma accelerators enable order of magnitude improvements in accelerating gradient and promise compact tunable GeV electron beam sources, while novel photocathode systems permit fundamental advances in electron beam manipulation for accelerator and radiation applications Advances in fast feedback systems are required to stabilize laser performance at kHz repetition rate operation against environmental fluctuations. A field programmable gate array (FPGA) based digital control system, coupled with responsive optics, can provide rapid and precise stabilization of ultrafast lasers. A collaboration between RadiaSoft and the Lawrence Berkeley National Laboratory BELLA Center to develop, test, and deploy these systems across a range of beamlines operating at >1 Hz repetition rate, including 1 kHz systems, was created.

The ever increasing demands placed upon machine performance have resulted in the need for more comprehensive particle accelerator modeling. Computer simulations are key to the success of particle accelerators. Many aspects of particle accelerators rely on computer modeling at some point, sometimes requiring complex simulation tools and massively parallel supercomputing. Examples include the modeling of beams at extreme intensities and densities (toward the quantum degeneracy limit), and with ultra-fine control (down to the level of individual particles). In the future, adaptively tuned models might also be relied upon to provide beam measurements beyond the resolution of existing diagnostics. Much time and effort has been put into creating accelerator software tools, some of which are highly successful. However, there are also shortcomings such as the general inability of existing software to be easily modified to meet changing simulation needs. In this paper possible mitigating strategies are discussed for issues faced by the accelerator community as it endeavors to produce better and more comprehensive modeling tools. This includes lack of coordination between code developers, lack of standards to make codes portable and/or reusable, lack of documentation, among others., 21 pages, 1 figure. To be published in JINST

Next generation accelerators demand sophisticated beam sources to produce ultra-low emittances with large gradients. The subsequent beamline optics are equally critical to transporting these beams between accelerating stages or to interaction points. Capillary discharge plasmas may address each of these challenges. Capillaries have been demonstrated as sources capable of increasing the peak energy and beam quality of laser wakefield accelerators, and as active plasma lenses featuring orders-of-magnitude increases in peak magnetic field. These systems are sensitive to energy deposition, heat transfer, ionization dynamics, and magnetic field penetration; therefore, improved modeling will enable advances in capillary design. We present simulations of capillary discharge waveguides and active plasma lenses in using FLASH, a publicly-available multi-physics code in development at the University of Chicago. We report on the implementation of a 2D, cylindrically symmetric capillary model for capturing plasma density and temperature evolution with realistic conductivities and magnetic fields. We then illustrate the use of laser energy deposition to model low density channel formation for the matching and guiding of intense laser pulses. Lastly, we discuss simulations of active capillary plasmas with different fill species, which show agreement with experimental observations of nonlinearities in the current density profile and magnetic field.

The ‘Trojan Horse’ underdense plasma photocathode scheme applied to electron beam-driven plasma wakefield acceleration has opened up a path which promises high controllability and tunability and to reach extremely good quality as regards emittance and five-dimensional beam brightness. This combination has the potential to improve the state-of-the-art in accelerator technology significantly. In this paper, we review the basic concepts of the Trojan Horse scheme and present advanced methods for tailoring both the injector laser pulses and the witness electron bunches and combine them with the Trojan Horse scheme. These new approaches will further enhance the beam qualities, such as transverse emittance and longitudinal energy spread, and may allow, for the first time, to produce ultrahigh six-dimensional brightness electron bunches, which is a necessary requirement for driving advanced radiation sources. This article is part of the Theo Murphy meeting issue ‘Directions in particle beam-driven plasma wakefield acceleration’.