Search

Biomaterials and synthetic polymers have been widely used to replicate the regenerative microenvironment of the peripheral nervous system. Chitosan-based conduits have shown promise in the regeneration of nerve injuries. However, to mimic the regenerative microenvironment, the scaffold structure should possess bioactive properties. This can be achieved by the incorporation of biomolecules (e.g., proteins, peptides) or trophic factors that should preferably be aligned and/or released with controlled kinetics to activate the process of positive axon chemotaxis. In this study, sodium L-lactate has been used to enhance the bioactive properties of chitosan-hydroxyapatite/polycaprolactone electrodeposits. Next, two methods have been developed to incorporate NGF-loaded microspheres - Method 1 involves entrapment and co-deposition of NGF-loaded microspheres, while Method 2 is based on absorption of NGF-loaded microspheres. The study shows that modification of chitosan-hydroxyapatite/polycaprolactone conduits by sodium L-lactate significantly improves their bioactive, biological, and physicochemical properties. The obtained implants are cytocompatible, enhancing the neurite regeneration process by stimulating its elongation. The absorption of NGF-loaded microspheres into the conduit structure may be considered more favorable for the stimulation of axonal elongation compared to entrapment, as it allows for trophic factor dose-dependent controlled release. The developed conduits possess properties essential for the successful treatment of peripheral nerve discontinuities., Competing Interests: Declaration of competing interest The authors declare the following financial interests/personal relationships which may be considered as potential competing interests: Katarzyna Nawrotek reports financial support was provided by the National Centre for Research and Development. Katarzyna Nawrotek has patent #P. 445788 A method of producing cylindrical-shaped implants activating the process of positive axon chemotaxis pending to The Patent Office of the Republic of Poland. If there are other authors, they declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 The Author(s). Published by Elsevier B.V. All rights reserved.)

Novel tissue regeneration strategies are constantly being developed worldwide. Research on bone regeneration is noteworthy, as many promising new approaches have been documented with novel strategies currently under investigation. Innovative biomaterials that allow the coordinated and well-controlled repair of bone fractures and bone loss are being designed to reduce the need for autologous or allogeneic bone grafts eventually. The current engineering technologies permit the construction of synthetic, complex, biomimetic biomaterials with properties nearly as good as those of natural bone with good biocompatibility. To ensure that all these requirements meet, bioactive molecules are coupled to structural scaffolding constituents to form a final product with the desired physical, chemical, and biological properties. Bioactive molecules that have been used to promote bone regeneration include protein growth factors, peptides, amino acids, hormones, lipids, and flavonoids. Various strategies have been adapted to investigate the coupling of bioactive molecules with scaffolding materials to sustain activity and allow controlled release. The current manuscript is a thorough survey of the strategies that have been exploited for the delivery of biomolecules for bone regeneration purposes, from choosing the bioactive molecule to selecting the optimal strategy to synthesize the scaffold and assessing the advantages and disadvantages of various delivery strategies.

Tubular polymeric structures have been recognized in the treatment of peripheral nerves as comparable to autologous grafting. The best therapeutic outcomes are obtained with conduits releasing therapeutic molecules. In this study, a new approach for the incorporation of biologically active agent-loaded microspheres into the structure of chitosan/polycaprolactone conduits was developed. The support of a polycaprolactone helix formed by 3D melt extrusion was coated with dopamine in order to adsorb nerve growth factor-loaded microspheres. The complex analysis of the influence of process factors on the coverage efficiency of polycaprolactone helix by nerve grow factor-loaded microspheres was analyzed. Thus, the PCL helix characterized with the highest adsorption of microspheres was subjected to nerve growth factor release studies, and finally incorporated into chitosan hydrogel deposit through the process of electrophoretic deposition. It was demonstrated by chemical and physical tests that the chitosan/polycaprolactone conduit meets the requirements imposed on peripheral nerve implants, particularly mimicking mechanical properties of surrounding soft tissue. Moreover, the conduit may support regrowing nerves for a prolonged period, as its structure and integrity persist upon incubation in lysozyme-contained PBS solution up to 28 days at body temperature. In vitro cytocompatibility toward mHippoE-18 embryonic hippocampal cells of the chitosan/polycaprolactone conduit was proven. Most importantly, the developed conduits stimulate axonal growth and support monocyte activation, the latter is advantageous especially at early stages of nerve regeneration. It was demonstrated that, through the described approach for controlling spatiotemporal release of nerve growth factors, these biocompatible structures adjusted to the specific peripheral nerve injury case can be manufactured.

Epigenetic processes, such as DNA methylation and other chromatin modifications, are believed to be largely responsible for establishing a reduced capacity for growth in the mature nervous system. Ten-eleven translocation methylcytosine dioxygenase 3 (Tet3)-, a member of the Tet gene family, plays a crucial role in promoting injury-induced DNA demethylation and expression of regeneration-associated genes in the peripheral nervous system. Here, we encapsulate Tet3 protein within a clinically tolerated poly(lactide-co-glycolide) microsphere system. Next, we show that Tet3-loaded microspheres are internalized into mHippoE-18 embryonic hippocampal cells. We compare the outgrowth potential of Tet3 microspheres with that of commonly used nerve growth factor (NGF)-loaded microspheres in an in vitro injury model. Tet3-containing microspheres increased levels of nuclear 5-hydroxymethylcytosine indicating active demethylation and outperformed NGF-containing microspheres in measures of neurite outgrowth. Our results suggest that encapsulated demethylases may represent a novel avenue to treat nerve injuries., (© 2021 The Authors. Journal of Tissue Engineering and Regenerative Medicine published by John Wiley & Sons Ltd.)

Tubular-shaped hydrogel structures were obtained in the process of cathodic electrodeposition from a chitosan-hydroxyapatite solution carried out in a cylindrical geometry. The impact of the initial concentration of solution components (i.e., chitosan, hydroxyapatite, and lactic acid) and process parameters (i.e., time and voltage) on the mass and structural properties of deposit was examined. Commercially available chitosan differs in average molecular weight and deacetylation degree; therefore, these parameters were also studied. The application of Fourier-transform infrared spectroscopy, scanning electron microscopy, and time-of-flight secondary ion mass spectrometry allowed obtaining fundamental information about the type of bonds and interactions created in electrodeposited structures. Biocompatible tubular implants are highly desired in the field of regeneration or replacement of tubular-shaped tissues and organs; therefore, the possibility of obtaining deposits with the desired structural properties is highly anticipated.

Major efforts for the advancement of tubular-shaped implant fabrication focused recently on the development of 3D printing methods that can enable the fabrication of complete devices in a single printing process. However, the main limitation of these solutions is the use of non-biocompatible polymers. Therefore, a new technology for obtaining hybrid implants that employ polymer extrusion and electrophoretic deposition is applied. The fabricated structures are made of two layers: polycaprolactone skeleton and chitosan-hydroxyapatite electrodeposit. Both of them can be functionalized by incorporation of mechanical or biological cues that favor ingrowth, guidance, and correct targeting of axons. The electrodeposition process is conducted at different voltages in order to determine the influence of this process on the structural, chemical, and mechanical properties of implants. In addition, changes in mechanical properties of implants during their incubation in phosphate-buffered solution (pH 7.4) at 37 °C up to 28 days are examined. The presented technology, being low-cost and relatively simple, shall find a broad scope of applications in customized nerve tissue engineering.

Tubular-shaped layer electrodeposition from chitosan-hydroxyapatite colloidal solutions has found application in the field of regeneration or replacement of cylindrical tissues and organs, especially peripheral nerve tissue regeneration. Nevertheless, the quantitative and qualitative characterisation of this phenomenon has not been described. In this work, the colloidal systems are subjected to the action of an electric current initiated at different voltages. Parameters of the electrodeposition process (i.e., total charge exchanged, gas volume, and deposit thickness) are monitored over time. Deposit structures are investigated by scanning electron microscopy (SEM) and Fourier-transform infrared spectroscopy (FTIR). The value of voltage influences structural characteristics but not thickness of deposit for the process lasting at least 20 min. The calculated number of exchanged electrons for studied conditions suggests that the mechanism of deposit formation is governed not only by water electrolysis but also interactions between formed hydroxide ions and calcium ions coordinated by chitosan chains., Competing Interests: The authors declare no conflict of interest.

Tubular chitosan-based hydrogels, obtained in an electrodeposition process, are subject of degradation and stability studies. The implants are prepared from polymer with different average molecular weight. This approach allows fabricating structures that vary in mass and wall thickness. The obtained implants are incubated in phosphate buffered solution (pH 7.4) with or without lysozyme up to 56 days at 37 °C. Subsequently, chemical, physical as well as mechanical properties of implants are evaluated. Although the initial physicomechanical properties are different, they change upon incubation and remain similar over its period. Finally, in vitro biocompatibility of implants is proven after assessing their action towards mHippoE-18 embryonic hippocampal cells and THP1-XBlue™ monocytes. Since dimensions of nerves and the gap length differ across the body and injury, respectively, the possibility to control properties of chitosan applied gives a tool to prepare implants with wall thickness adjusted to the specific peripheral nerve injury case., (Copyright © 2020 Elsevier Ltd. All rights reserved.)

One of the most intriguing features of the brain is its ability to be malleable, allowing it to adapt continually to changes in the environment. Specific neuronal activity patterns drive long-lasting increases or decreases in the strength of synaptic connections, referred to as long-term potentiation and long-term depression, respectively. Such phenomena have been described in a variety of model organisms, which are used to study molecular, structural, and functional aspects of synaptic plasticity. This review originated from the first International Society for Neurochemistry (ISN) and Journal of Neurochemistry (JNC) Flagship School held in Alpbach, Austria (Sep 2016), and will use its curriculum and discussions as a framework to review some of the current knowledge in the field of synaptic plasticity. First, we describe the role of plasticity during development and the persistent changes of neural circuitry occurring when sensory input is altered during critical developmental stages. We then outline the signaling cascades resulting in the synthesis of new plasticity-related proteins, which ultimately enable sustained changes in synaptic strength. Going beyond the traditional understanding of synaptic plasticity conceptualized by long-term potentiation and long-term depression, we discuss system-wide modifications and recently unveiled homeostatic mechanisms, such as synaptic scaling. Finally, we describe the neural circuits and synaptic plasticity mechanisms driving associative memory and motor learning. Evidence summarized in this review provides a current view of synaptic plasticity in its various forms, offers new insights into the underlying mechanisms and behavioral relevance, and provides directions for future research in the field of synaptic plasticity. Read the Editorial Highlight for this article on page 788. Cover Image for this issue: doi: 10.1111/jnc.13815., (© 2017 International Society for Neurochemistry.)

The present study was designed to provide an appropriate micro-environment for regenerating axotomized neurons and proliferating/migrating cells. Because of its intrinsic permissive properties, biocompatibility and biodegradability, we chose to evaluate the therapeutic effectiveness of a chitosan-based biopolymer. The biomaterial toxicity was measured through in vitro test based on fibroblast cell survival on thermogelling chitosan lactate hydrogel substrate and then polymer was implanted into a C2 hemisection of the rat spinal cord. Animals were randomized into three experimental groups (Control, Lesion and Lesion + Hydrogel) and functional tests (ladder walking and forelimb grip strength tests, respiratory assessment by whole-body plethysmography measurements) were used, once a week during 10 weeks, to evaluate post-traumatic recoveries. Then, electrophysiological examinations (reflexivity of the sub-lesional region, ventilatory adjustments to muscle fatigue known to elicit the muscle metaboreflex and phrenic nerve recordings during normoxia and temporary hypoxia) were performed. In vitro results indicated that the chitosan matrix is a non-toxic biomaterial that allowed fibroblast survival. Furthermore, implanted animals showed improvements of their ladder walking scores from the 4th week post-implantation. Finally, electrophysiological recordings indicated that animals receiving the chitosan matrix exhibited recovery of the H-reflex rate sensitive depression, the ventilatory response to repetitive muscle stimulation and an increase of the phrenic nerve activity to asphyxia compared to lesioned and nonimplanted animals. This study indicates that hydrogel based on chitosan constitute a promising therapeutic approach to repair damaged spinal cord or may be used as an adjuvant with other treatments to enhance functional recovery after a central nervous system damage. © 2016 Wiley Periodicals, Inc. J Biomed Mater Res Part A: 105A: 2004-2019, 2017., (© 2017 Wiley Periodicals, Inc.)

In this investigation, we report on a fabrication method of epineurium-mimicking tubular conduits based on electrodeposition from chitosan solution. The pre-enrichment of electrodeposition solution with hyaluronic acid and/or collagen components results in structures which structural, morphological, and physicochemical properties can be controlled. In order to determine the optimal composition of the initial chitosan solution resulting in conduits meeting the requirements imposed on peripheral nerve implants, we perform chemical, physical, and biological studies. Both the molecular weight of hyaluronic acid and the concentration of additives are found to be crucial for the final mechanical as well as biological performance of conduits. Because, the obtained structures show biocompatibility when contacting with a mouse hippocampal cell line (mHippoE-18), we further plan to test their application potential on an animal model., (Copyright © 2016 Elsevier Ltd. All rights reserved.)

Designing three-dimensional tubular materials made of chitosan is still a challenging task. Availability of such forms is highly desired by tissue engineering, especially peripheral nerve tissue engineering. Aiming at this problem, we use an electrodeposition phenomenon in order to obtain chitosan and chitosan-carbon nanotube hydrogel tubular implants. The in vitro biocompatibility of the fabricated structures is assessed using a mouse hippocampal cell line (mHippoE-18). As both implants do not induce significant cytotoxicity, they are next subjected to in vitro degradation studies in the environment simulating in vivo conditions for specified periods of time: 7, 14, and 28 days. The mass loss of implants indicates their stability at the tested time period; therefore, the materials are subcutaneously implanted in Sprague Dawley rats. The explants are collected after 7, 14, and 28 days. The assessment of composition and changes in tissues surrounding the implanted materials is made in respect to surrounding tissue thickness as well as the number of blood vessels, macrophages, lymphocytes, and neutrophils. No symptoms of acute inflammation are noticed at any point in time. The observed regular healing process allows concluding that both chitosan and chitosan-carbon hydrogel tubular implants are biocompatible with high application potential in tissue engineering. © 2016 Wiley Periodicals, Inc. J Biomed Mater Res Part A: 104A: 2701-2711, 2016., (© 2016 Wiley Periodicals, Inc.)

A new approach for obtaining chitosan-carbon nanotube implants enriched with calcium ions in the form of tubular hydrogels is fostered. The intended application of the hydrogels is tissue engineering, especially peripheral nervous tissue regeneration. The fabrication method, based on an electrodeposition phenomenon, shows significant advantages over current solutions as implants can now be obtained rapidly at any required dimensions. Thus, it may open a new avenue to treat patients with peripheral nerve injuries. Either single walled or multiwalled carbon nanotubes enhance the mechanical properties of the tubular hydrogels. The controlled presence of calcium ions, sourced from hydroxyapatite, is also expected to augment the regenerative response. Because in vitro cytotoxic assays on mouse cell lines (L929 fibroblasts and mHippoE-18 hippocampal cells) as well as pro-inflammatory tests on THP-1XBlue™ cells show that the manufactured implants are biocompatible, we next intend to evaluate their immune- and nervous-safety on an animal model., (Copyright © 2016 Elsevier Ltd. All rights reserved.)

A new method for fabrication of chitosan-based hydrogel implants intended for peripheral nervous tissue regeneration was developed. The method is based on an electrodeposition phenomenon from a solution of chitosan and organic acid. In order to increase the mechanical strength of the implant, the solution was enriched with hydroxyapatite. Hydroxyapatite served as a source of calcium ions too. The influence of the concentration of the polymer and the additive on chemical, mechanical as well as biological properties of the obtained implant was evaluated. The study showed great dependence of the initial solution composition mainly on the physicochemical properties of the resulting structure. Basic in vitro cytotoxic and pro-inflammatory assays showed biocompatibility of manufactured implants, therefore, animal experimentations may be considered., (Copyright © 2015 Elsevier Ltd. All rights reserved.)