Search

The aim of this study is to analyze the effect of the addition of TiO2 nanoparticles (NTs) on the physical and mechanical properties, as well as the microstructural changes, of cementitious composites containing partially substituted natural aggregates (NAs) with aggregates derived from the following four recycled materials: glass (RGA), brick (RGB), blast-furnace slag (GBA), and recycled textolite waste with WEEE (waste from electrical and electronic equipment) as the primary source (RTA), in line with sustainable construction practices. The research methodology included the following phases: selection and characterization of raw materials, formulation design, experimental preparation and testing of specimens using standardized methods specific to cementitious composite mortars (including determination of apparent density in the hardened state, mechanical strength in compression, flexure, and abrasion, and water absorption by capillarity), and structural analysis using specialized techniques (scanning electron microscopy (SEM) images and energy dispersive X-ray spectroscopy (EDS)). The analysis and interpretation of the results focused primarily on identifying the effects of NT addition on the composites. Results show a decrease in density resulting from replacing NAs with recycled aggregates, particularly in the case of RGB and RTA. Conversely, the introduction of TiO2 nanoparticles resulted in a slight increase in density, ranging from 0.2% for RTA to 7.4% for samples containing NAs. Additionally, the introduction of TiO2 contributes to improved compressive strength, especially in samples containing RTA, while flexural strength benefits from a 3–4% TiO2 addition in all composites. The compressive strength ranged from 35.19 to 70.13 N/mm2, while the flexural strength ranged from 8.4 to 10.47 N/mm2. The abrasion loss varied between 2.4% and 5.71%, and the water absorption coefficient varied between 0.03 and 0.37 kg/m2m0.5, the variations being influenced by both the nature of the aggregates and the amount of NTs added. Scanning electron microscopy (SEM) images and energy dispersive X-ray spectroscopy (EDS) analysis showed that TiO2 nanoparticles are uniformly distributed in the cementitious composites, mainly forming CSH gel. TiO2 nanoparticles act as nucleating agents during early hydration, as confirmed by EDS spectra after curing. [ABSTRACT FROM AUTHOR]

The conservation of the environment and the protection of natural resources are urgent and current challenges. The objective of this experimental investigation was to evaluate the potential use of aggregates derived from recycled glass waste, blast furnace slag, recycled brick waste aggregates and recycled electronic waste aggregates (textolite) as replacements for natural aggregates in cement-based composites. The experimental tests aimed to investigate how the replacement of natural aggregates with recycled waste aggregates affects various physico-mechanical parameters, including density, compressive strength, flexural strength, abrasion resistance and capillary water absorption. This investigation also included detailed microstructural analysis using optical microscopy, SEM, EDX and XRD techniques. The aim of the research was to explore the potential for soil conservation by reducing the amount of waste to be disposed of, and at the same time to conserve natural resources by identifying alternatives using recycled materials, thereby contributing to the implementation of the circular economy concept. The results of the research confirmed this potential; however, depending on the nature of the recycled aggregates, there are influences on the physico-mechanical performance of the cement composite that can be seen at the microstructural level. [ABSTRACT FROM AUTHOR]

Our study is focused on optimizing the synthesis conditions for the in situ oxidation of Fe particles to produce Fe@Fe3O4 core–shell powder and preparation via co-precipitation of ZnFe2O4 nanoparticles to produce Fe@Fe3O4/ZnFe2O4 soft magnetic composites (SMC) through a hybrid cold-sintering/spark plasma-sintering technique. XRD and FTIR measurements confirmed the formation of a nanocrystalline oxide layer on the surface of Fe powder and the nanosized nature of ZnFe2O4 nanoparticles. SEM-EDX investigations revealed that the oxidic phase of our composite was distributed on the surface of the Fe particles, forming a quasi-continuous matrix. The DC magnetic characteristics of the composite compact revealed a saturation induction of 0.8 T, coercivity of 590 A/m, and maximum relative permeability of 156. AC magnetic characterization indicated that for frequencies higher than 1 kHz and induction of 0.1 T, interparticle eddy current losses dominated due to ineffective electrical insulation between neighboring particles in the composite compact. Nevertheless, the magnetic characteristics obtained in both DC and AC magnetization regimes were comparable to those reported for cold-sintered Fe-based SMCs. [ABSTRACT FROM AUTHOR]

Soft magnetic composite (SMC) cores have been obtained by Spark Plasma Sintering (SPS) using pseudo core–shell powders. Pseudo core–shell powders are formed by a core of soft magnetic particle (nanocrystalline permalloy or supermalloy) surrounded by a thin layer (shell) of nanosized soft ferrite (Mn0.5Zn0.5Fe2O4). Three compositions of pseudo core–shell powders were prepared, with 1, 2 and 3 wt.% of manganese–zinc mixt ferrite. The pseudo core–shell powders were compacted by SPS at temperatures between 500 and 700 °C, with a holding time ranging from 0 to 10 min. Several techniques have been used for characterization of the samples, both, powders and compacts X-ray diffraction (XRD, scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDX), magnetic hysteresis measurements (DC and AC) and electrical resistivity. The electrical resistivity is in the order of 1 × 10−2 Ωm, 3–4 orders of magnitude higher than supermalloy electrical resistivity. The SPS at lower temperatures (500 °C) conserves the initial phases of the composite, but increasing the sintering temperature and/or sintering time produces a solid-state reaction between the alloy and ferrite phases, with negative consequence on the magnetic properties of the compacts. The initial relative permeability is around 40 and remains constant until to 2000 Hz. The power losses are lower than 2 W/kg until to 2000 Hz. [ABSTRACT FROM AUTHOR]

The use of waste from industrial activities is of particular importance for environmental protection. Fly ash has a high potential in the production of construction materials. In the present study, the use of fly ash in the production of geopolymer paste and the effect of Fe2O3, MgO and molarity of NaOH solution on the mechanical strength of geopolymer paste are presented. Samples resulting from the heat treatment of the geopolymer paste were subjected to mechanical tests and SEM, EDS and XRD analyses. Samples were obtained using 6 molar and 8 molar NaOH solution with and without the addition of Fe2O3 and MgO. Samples obtained using a 6 molar NaOH solution where Fe2O3 and MgO were added had higher mechanical strengths compared to the other samples. [ABSTRACT FROM AUTHOR]