Search

This work reports the thermal, rheological, and crystallographic structural behavior of recycled polyethylene terephthalate (rPET) derived from bottle waste. The intent is to optimize it to an upcoming source for additive manufacturing by modulating its behavior using a chain extender triphenyl phosphite (TPP), nanofiller montmorillonite (MMT K-10), and catalyst antimony trioxide (Sb2[O.sub.3]). FT-IR (Fourier Transform Infrared) analysis showed an increase in absorbance due to the Sb2[O.sub.3]. The thermal analysis of the rPET using differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) ascertains a 10[degrees]C decrease in [T.sub.g] with a substantial increase in the degradation onset of 7[degrees]C due to MMT content. The melt flow index (MFI) study showed an increase with a similar range in intrinsic viscosity and weight average molecular weight ([M.sub.w]) due to the additives. The percentage crystallinity, interlayer distance, and average crystallite size are determined and analyzed by X-ray diffraction (XRD) and DSC curves. The results are within the comparative range of both tests. The presence of Sb2[O.sub.3] with higher MMT content showed agglomeration, and increased TPP showed low crystalline properties. These results provide that rPET can be altered to manufacture feedstock to suit different 3D printing techniques for prototyping. KEYWORDS additive manufacturing, nanocomposite, recycled PET, sustainability, 1 | INTRODUCTION Additive manufacturing has been gaining attention in the product manufacturing field for the last decade. This is because it removes the need to manufacture molds to make [...]

Sulfonated poly(oxy‐1,4‐phenylene‐oxy‐1,4‐phenylenecarbonyl‐1,4‐phenylene) also known as SPEEK is a chemically robust cation conductor with good solution processability. A thin film (approx. 0.7 μm) coated asymmetrically over a 10 μm diameter microhole in a Teflon substrate film (5 μm thickness) produces ionic diode effects in aqueous electrolyte media even at high ionic strengths up to 2 M NaCl. The enhancement in the ionic diode performance under high salt conditions is tentatively attributed to a (partial) switch from a concentration polarisation effect (dominant for high diode currents) to interfacial polarisation (dominant at low current; proposed for molecularly rigid ionomers). Ionic strength effects on the diode performance seem relatively low further indicative of a mechanism for the diode effect caused by interfacial polarisation without significant concentration polarisation. Preliminary comparison of diode phenomena in aqueous HCl, LiCl, NaCl, and MgCl2 reveals cation specific effects due to interaction with the polymer. [ABSTRACT FROM AUTHOR]

Pure organic films consisting of polypyrrole, polyaniline and a composite of polypyrrole and polyaniline electrodeposited in the ionic liquid EMIM‐TFSI onto mesoporous carbon electrodes are tested for their hydrogen evolution reaction capabilities. The use of these intrinsically conducting polymers is seen as a way of stepping away from expensive and rare metallic catalysts. Co‐polymerisation of polypyrrole and polyaniline in a 1 : 10 ratio in EMIM‐TFSI was found to be doped with the TFSI− anion and be much more active to the hydrogen evolution reaction when compared to pure polymers. Tafel analysis of the composite gave a value of 144 mV/dec indicating that the Volmer step is the rate limiting step. However, stability tests showed an improvement in the composite's overpoential performance for the hydrogen evolution reaction. [ABSTRACT FROM AUTHOR]

Insufficient proton conductivity and oxidative stability of sulfonated hydrocarbons hinder their applicability as proton exchange membrane electrolytes in fuel cells. In this regard, fabrication of proton conducting mixed-matrix membranes (PC-MMMs) can be a superior approach to obtain desirable properties. In this work, a triazole ligand (1H-1,2,4 triazole) was coordinated to a zinc metal node to create a 3D metal–organic framework (MOF) and incorporated as an additive in a sulfonated poly(ether ether ketone) matrix at 1, 3, and 5 weight percentage to fabricate PC-MMMs by the casting process. Several characterization tools such as electrochemical impedance spectroscopy, Fourier transform infrared spectroscopy and scanning electron microscopy were used to characterise these membranes and study their potential application as electrolyte(s) in PEMFCs (proton exchange membrane fuel cells). Membranes were also tested for water uptake, ion-exchange capacity and oxidative stability in Fenton's reagent. The performance of the polymeric composite membrane containing a 3 wt% MOF was then assessed in a H2/O2 single cell as it demonstrated the highest proton conductivity of 0.04 S cm−1 among all the compositions and a maximum current density of 1191 mA cm−2. The membrane was also subjected to an OCV hold test for 12 hours to study the chemical durability over a period of time. This report establishes that the inclusion of a triazole based MOF enhances the proton conductivity, performance, and thermal and chemical durability of composite membranes which can be considered as a promising electrolyte material at intermediate temperatures after a proper optimisation of different cell parameters. [ABSTRACT FROM AUTHOR]

In this study, a new waterborne acrylic copolymer resin (acrylic-co-resin) was synthesized to develop water-based printing inks on polyester (PET) film. The synthesized acrylic resin showed good water solubility, high acid value (120 mg KOH/g), about 57% solid content. The developed water-based inks (cyan, magenta, and yellow) exhibited small particle size ( KEYWORDS acrylic resin, adhesion, printing, water-based printing ink, 1 | INTRODUCTION Printing ink plays an essential role in the packaging area, and the demand for printing inks is increasing day-by-day all over the world. [1,2] Due to the [...]