Search

Abstract: In this paper, we report the global fuel energy consumption in heavy-duty road vehicles due to friction in engines, transmissions, tires, auxiliary equipment, and brakes. Four categories of vehicle, representing an average of the global fleet of heavy vehicles, were studied: single-unit trucks, truck and trailer combinations, city buses, and coaches. Friction losses in tribocontacts were estimated by drawing upon the literature on prevailing contact mechanics and lubrication mechanisms. Coefficients of friction in the tribocontacts were estimated based on available information in the literature for four cases: (1) the average vehicle in use today, (2) a vehicle with today׳s best commercial tribological technology, (3) a vehicle with today׳s most advanced technology based upon recent research and development, and (4) a vehicle with the best futuristic technology forecasted in the next 12 years. The following conclusions were reached: [•] In heavy duty vehicles, 33% of the fuel energy is used to overcome friction in the engine, transmission, tires, auxiliary equipment, and brakes. The parasitic frictional losses, with braking friction excluded, are 26% of the fuel energy. In total, 34% of the fuel energy is used to move the vehicle. [•] Worldwide, 180,000 million liters of fuel was used in 2012 to overcome friction in heavy duty vehicles. This equals 6.5millionTJ/a; hence, reduction in frictional losses can provide significant benefits in fuel economy. A reduction in friction results in a 2.5 times improvement in fuel economy, as exhaust and cooling losses are reduced as well. [•] Globally a single-unit truck uses on average 1500l of diesel fuel per year to overcome friction losses; a truck and trailer combination, 12,500l; a city bus, 12,700l; and a coach, 7100l. [•] By taking advantage of new technology for friction reduction in heavy duty vehicles, friction losses could be reduced by 14% in the short term (4 to 8 years) and by 37% in the long term (8 to 12 years). In the short term, this would annually equal worldwide savings of 105,000 million euros, 75,000 million liters of diesel fuel, and a CO2 emission reduction of 200 million tones. In the long term, the annual benefit would be 280,000 million euros, 200,000 million liters of fuel, and a CO2 emission reduction of 530 million tonnes. [•] Hybridization and electrification are expected to penetrate only certain niches of the heavy-duty vehicle sector. In the case of city buses and delivery trucks, hybridization can cut fuel consumption by 25% to 30%, but there is little to gain in the case of coaches and long-haul trucks. Downsizing the internal combustion engine and using recuperative braking energy can also reduce friction losses. [•] Electrification is best suited for city buses and delivery trucks. The energy used to overcome friction in electric vehicles is estimated to be less than half of that of conventional diesel vehicles. Potential new remedies to reduce friction in heavy duty vehicles include the use of advanced low-friction coatings and surface texturing technology on sliding, rolling, and reciprocating engine and transmission components, new low-viscosity and low-shear lubricants and additives, and new tire designs that reduce rolling friction. [Copyright &y& Elsevier]

This study reports high numbers of exhaust emissions particles during engine motoring. Such particles were observed in the exhaust of two heavy duty vehicles with no diesel particle filter (DPF), driven on speed ramp tests and transient cycles. A significant fraction of these particles was nonvolatile in nature. The number-weighted size distribution peak was below 10 nm when a thermodenuder was used to remove semivolatile material, growing up to 40 nm after semivolatile species condensation. These particles were found to contribute to 9-13% of total particle number emitted over a complete driving cycle. Engine motoring particles originated from lube oil and evidence suggests that these are of heavy organic or organometallic material. Particles of similar characteristics have been observed in the core particle mode during normal fired engine operation. Their size and chemical character has implications primarily on die environmental toxicity of non-DPF diesel and, secondarily, on the performance of catalytic devices and DPFs. Lube oil formulation measures can be taken to reduce the emission of such particles. [ABSTRACT FROM AUTHOR]

Demonstrates the air quality improvement in a small indoor ice arena in Finland. Measurement and control of exhaust emissions; Indoor air quality measurement; Protocol for air quality follow-up; Reduction of resurface emissions; Initial air quality and standardization of ventilation in ice arena; Effect of emission control system on indoor air quality.