Search

In view of safe management of the nuclear wastes, a sound knowledge of the atomic-scale properties of U1-xMxO2+y nanoparticles is essential. In particular, their cation valences and oxygen stoichiometries are of great interest as these properties drive their diffusion and migration behaviors into the environment. Here, we present an in-depth study of U1-xCexO2+y, over the full compositional domain, by combining X-ray diffraction and high-energy resolution fluorescence detection X-ray absorption near-edge structure. We show, on one hand, the coexistence of UIV, UV, and UVI and, on the other hand, that the fluorite structure is maintained despite this charge distribution.

The transmutation of minor actinides (in particular, Np and Am), which are among the main contributors to spent fuel α-radiotoxicity, was studied in the SUPERFACT irradiation. Several types of transmutation UO2-based fuels were produced, differing by their minor actinide content (241Am, 237Np, Pu), and irradiated in the Phénix fast reactor. Due to the high content in rather short-lived alpha-decaying actinides, both the archive, but also the irradiated fuels, cumulated an alpha dose during a laboratory time scale, which is comparable to that of standard LWR fuels during centuries/millenaries of storage. Transmission Electron Microscopy was performed to assess the evolution of the microstructure of the SUPERFACT archive and irradiated fuel. This was compared to conventional irradiated spent fuel (i.e., after years of storage) and to other 238Pu-doped UO2 for which the equivalent storage time would span over centuries. It could be shown that the microstructure of these fluorites does not degrade significantly from low to very high alpha-damage doses, and that helium bubbles precipitate.

International audience; 238Pu-doped UO2 was characterised periodically to investigate the long-term effects of α-self-irradiation on spent nuclear fuel. Samples of two compositions (1.25 and 5% wt 238Pu), were studied by means of X-ray diffraction (XRD), Raman spectroscopy, and transmission electron microscopy (TEM). The cumulated dose received by the samples was measured in displacements per atom (dpa) to allow comparison between the two samples and to the literature values. XRD characterization showed that the lattice swelling approached saturation at 0.3% of the lattice parameter of the cubic cell at 0.4 dpa damage accumulation. Microstrain decreased for the whole duration of the study, as a result of point defect recombination into dislocation loops that were observed by TEM for dpa as low as 0.072. Raman highlighted the broadening of the T2g band and the increase and broadening of the defect triplet band. Both batches of samples followed the same trend if plotted against dpa, proving that for these dopant concentrations the self-irradiation effects do not depend on the rate of radiation damage creation in the matrix.

International audience; • SIMS and TEM techniques were combined to compare the thermal behaviour of Cs and Xe in UO 2 . • Both elements form bubbles with different growth kinetics. • At 1600 °C, caesium is found to be highly mobile in the UO 2 matrix while Xe distribution does not evolve.

International audience; This study aims to evaluate the influence of a metallic fission product, molybdenum, on the behaviour of caesium in UO2 at high temperature (1600°C) under reducing atmosphere. Both elements were successively introduced by ion implantation (firstly Mo, then Cs) at room temperature at a fluence of 1016 ions/cm². We show that in these co-implanted samples, the defects created by the Mo implantation render possible the nucleation of nanometric size bubbles during Cs implantation at room temperature. SIMS and TEM techniques were coupled in order to characterize the migration of both elements, as well as the UO2 microstructure evolution after annealing at 1600°C. We found that Mo is more mobile in presence of Cs, which may be related to an increase of available vacancies in the material produced by Cs implantation. On the contrary, the concentration profiles of Cs remain quite similar than when it is solely implanted, and its release percentage remain the same both in absence and presence of Mo. After annealing, both elements are found to be associated as Mo metallic precipitates and Cs bubbles distributed over the same depth (~150 nm). Comparing with the Cs bubbles distribution in absence of Mo, it is clear that the formation of Mo metallic precipitates hinders the Cs bubble migration. Our study highlights the role of dislocations on the nucleation of bubbles and metallic precipitates.

In the context of a comprehensive campaign for the characterisation of transmutation fuels for next generation nuclear reactors, the melting behaviour of mixed uranium-americium dioxides has been experimentally studied for the first time by laser heating, for Am concentrations up to 70 mol. % under different types of atmospheres. Extensive post-melting material characterisations were then performed by X-ray absorption spectroscopy and electron microscopy. The melting temperatures observed for the various compositions follow a markedly different trend depending on the experimental atmosphere. Uranium-rich samples melt at temperatures significantly lower (around 2700 K) when they are laser-heated in a strongly oxidizing atmosphere compressed air at (0.300 ± 0.005) MPa, compared to the melting points (beyond 3000 K) registered for the same compositions in an inert environment (pressurised Ar). This behaviour has been interpreted on the basis of the strong oxidation of such samples in air, leading to lower-melting temperatures. Thus, the melting temperature trend observed in air is characterized, in the purely pseudo-binary dioxide plane, by an apparent maximum melting temperature around 2850 K for 0.3 < x(AmO2) < 0.5. The melting points measured under inert atmosphere uniformly decrease with increasing americium content, displaying an approximately ideal solution behaviour if a melting point around 2386 K is assumed for pure AmO2. In reality, it will be shown that the (U, Am)-oxide system can only be rigorously described in the ternary U-Am-O phase diagram, rather than the UO2-AmO2 pseudo-binary, due to the aforementioned over-oxidation effect in air. Indeed, general departures from the oxygen stoichiometry (Oxygen/Metal ratios ≠ 2.0) have been highlighted by the X-ray Absorption Spectroscopy (XAS). Finally, to help interpret the experimental results, thermodynamic computations based on the CALPHAD method will be presented.

The development of tailored targets for the production of radioactive isotopes represents an active field in nuclear research. Radioactive beams find applications in nuclear medicine, in astrophysics, matter physics and materials science. In this work, we study the use of graphene both as carbon source for UO2 carbothermal reduction to produce UCx targets, and also as functional properties booster. At fixed composition, the UCx target grain size, porosity and thermal conductivity represent the three main points that affect the target production efficiency. UCx was synthesized using both graphite and graphene as the source of carbon and the target properties in terms of composition, grain size, porosity, thermal diffusivity and thermal conductivity were studied. The main output of this work is related to the remarkable enhancement achieved in thermal conductivity, which can profitably improve thermal dissipation during operational stages of UCx targets.

Uranium-molybdenum (UMo) alloy powder embedded in an Al matrix is considered as a promising candidate for fuel conversion of research reactors. A modified system with a diffusion barrier X as coating, UMo/X/Al trilayer (X = Ti, Zr, Nb, and Mo), has been investigated to suppress interdiffusion between UMo and the Al matrix. The trilayer systems were tested by swift heavy ion irradiation, the thereby created interaction zone has been analyzed by scanning transmission electron microscopy (STEM) and energy-dispersive X-ray spectroscopy (EDX). Detailed structural characterization are presented and compared to earlier μ-XRD analysis.

Within Europe 241 Am is a feasible alternative to 238 Pu that can provide a heat source for radioisotope thermoelectric generators (RTGs) and radioisotope heating units (RHUs) to be used in Electrical power sources used in outer planet missions. In the EPSO-SPACE* project developed as an exploratory research at JRC, a new type of nuclear power source, to provide heat and electricity for deep space missions is considered. It will consist of a 241 Am based compound with aerogel thermal insulation and thermocouples in close contact with the heat source. The assembly is inside an iridium encapsulation to withstand all relevant accident scenarios. The design will be modular and combinable for required electrical output.Several candidate Americium compounds will be investigated for chemical stability at high temperature and for self-irradiation damage. New thermo-electric converter materials containing actinides will be assessed, and a robust encapsulation designed. Safety analyses will be performed including launch explosion and re-entry accidents. The research will conclude in a conceptual design of a prototype power source. In the first part of this study, americium dioxide will be considered from the point of view of its chemical durability and of its behavior against radiation damage and helium formation, two aspects to be carefully investigated due to the high alpha-activity of the americium. Transmission electron Microscopy (TEM) and helium thermal desorption spectrometry (TDS) experiments will be described and results on aged (more than 30 years) AmO2 reported. Some comparison with 238 PuO2 based RTG’s will be discussed.

The production of very long glass nanofibers with lengths up to several centimeters was demonstrated using the Laser Spinning technique. It employs a laser to melt a small volume of a solid precursor material while a high-pressure gas jet drags the molten material away. Thus, the molten material forms glass fibers as result of its viscous elongation by the drag force and rapid cooling promoted by the gas jet. High quantities of nanofibers can be quickly produced with tailored chemical compositions. Previously reported analyses of the process revealed that the dimensions and temperature of the molten volume together with its viscosity to surface tension ratio are the main factors governing the formation of the nanofibers. Therefore, the influence of the working conditions on these parameters must be understood to control the efficiency of the process. In this work, we demonstrate that the surface tension of the melt can be controlled independently of its temperature, and consequently of its viscosity, by adjusting the relative humidity of the gas jet. This outcome increases the productivity of the process and expands its capability for the synthesis of glass nanofibers from fragile melts.

Laser Spinning is a new technique that has been shown to quickly produce amorphous inorganic nanofibers from bulk material under atmospheric conditions. This technique employs a high power laser to melt a small volume of the precursor material while a supersonic gas jet provokes its rapid elongation and cooling, producing long micro- and nanofibers within a range of diameters. In this work, the quantity of the fibers produced and the distribution of their diameters are measured and statistically analyzed for different operating conditions. The advance speed of the laser beam over the precursor material is experimentally demonstrated to be the most influencing factor on the diameter of the fibers. Other variables of the process, such as assist gas pressure, were found to have less influence.

INTRODUCTION: The objective of this study is to analyze the Spanish scientific publications in requirements engineering, comparing them with those of the European Union countries. METHOD: Identification, using several procedures, of 2625 publications with which the analysis has been carried out. RESULTS: Quantitative data about the volume of scientific publication, researchers’ productivity, publication patterns and collaboration patterns have been obtained for both Spain and the other European Union countries. CONCLUSIONS: Spain averages similar European countries in both volume of publication and researchers’ productivity. On the contrary, several drawbacks regarding publication and collaboration patterns were identified. Concretely, it has been observed that: (1) Spanish researchers publish an important percentage of papers in low-importance outlets and (2) collaboration with other researchers, either from foreign countries or industrial/commercial organizations, is particularly low, so that most of the papers are authored only by members of Spanish university research groups.

Nanocomposites made of non-woven glass fibres with diameters ranging from tens of nanometers up to several micrometers, containing silver nanoparticles, were successfully fabricated by the laser spinning technique. Pellets of a soda-lime silicate glass containing silver nanoparticles with varying concentrations (5 and 10 wt%) were used as a precursor. The process followed to obtain the silver nanofibres did not agglomerate significantly the metallic nanoparticles, and the average particle size is still lower than 50 nm. This is the first time that glass nanofibres containing silver nanoparticles have been obtained following a process different from electrospinning of a sol–gel, thus avoiding the limitations of this method and opening a new route to composite nanomaterials. Antibacterial efficiency of the nanosilver glass fibres, tested against one of the most common Gram negative bacteria, was greater than 99.99% compared to the glass fibres free of silver. The silver nanoparticles are well-dispersed not only on the surface but are also embedded into the uniform nanofibres, which leads to a long lasting durable antimicrobial effect. All these novel characteristics will potentially open up a whole new range of applications., This work was supported by Xunta de Galicia (10DPI303014PR) and the Spanish Ministry of Science and Innovation (MICINN) under the project MAT2009-14542-C02-02.

Laser Spinning is a new technique to produce ultralong amorphous ceramic nanofibers with tailored chemical compositions. In this method, a high power laser is employed to melt a small volume of the precursor material at high temperatures. At the same time, a supersonic gas jet is injected on this molten volume producing its rapid cooling and elongation by viscous friction with the high speed gas flow, hence forming the amorphous nanofibers.An experimental and theoretical analysis of the process was carried out in order to precisely ascertain the influence of the operating conditions on the formation of the fibers. A mathematical model of the cooling and elongation processes was developed to study the influence of the initial physical state of the molten volume on the formation of the nanofibers. Additionally, a second mathematical model was solved to analyze the changes on the fusion front with the operating conditions since they determine the state of the molten material at the beginning of the elongation process. Both models were verified and interrelated by analyses of the experimental results and direct observation, using a high speed camera, of the fusion front and the elongation of a molten filament during Laser Spinning.Laser Spinning is a new technique to produce ultralong amorphous ceramic nanofibers with tailored chemical compositions. In this method, a high power laser is employed to melt a small volume of the precursor material at high temperatures. At the same time, a supersonic gas jet is injected on this molten volume producing its rapid cooling and elongation by viscous friction with the high speed gas flow, hence forming the amorphous nanofibers.An experimental and theoretical analysis of the process was carried out in order to precisely ascertain the influence of the operating conditions on the formation of the fibers. A mathematical model of the cooling and elongation processes was developed to study the influence of the initial physical state of the molten volume on the formation of the nanofibers. Additionally, a second mathematical model was solved to analyze the changes on the fusion front with the operating conditions since they determine the state of the molten material at the beginning of the elongatio...

Software process evaluation is an essential activity for improving software development in an organisation. Actually there is a need for a formalised method of evaluation that encompasses all the factors that affect software production. If a software process evaluation is to faithfully reflect the current status of an organisation, it must also consider the assessment of other factors. A formalised method of evaluation is presented that jointly assesses the three essential factors in software production: processes, technology and human resources. The aim behind this is to provide a solution to the main shortcomings of current software process evaluation methods: partiality of the evaluated factors and non-formalisation of the evaluation processes. Experimentation in various organisations has proven the adequacy of the proposed method for obtaining results that accurately portray the current status of the organisation's software process.

Laser spinning is a new technique which has recently been demonstrated to produce ultralong amorphous ceramic nanofibres with controllable chemical compositions. A laser is employed to melt a small volume of the precursor material at high temperatures, while a supersonic gas jet is then used to rapidly elongate the molten material. The melt forms glass fibres as a result of its viscous elongation and rapid cooling by the convective heat transfer produced by the gas jet.This work analyses the relation between the operating conditions of laser spinning and the physical process that leads to the formation of nanofibres, with the purpose of controlling and designing the optimum conditions for the process. Two decoupled mathematical models were developed to study, on the one hand, the influence of the initial temperature and volume of the molten material on its elongation process, whereas the second model is solved to analyse the physics of the fusion front as a function of the process parameters and relate it to the process of producing the fibres. These models were verified and complemented by experimental tests studied by analyses of the products and direct observation of the fusion front using a high speed camera.

UO2 samples doped with the strong α-emitter 238Pu were periodically characterised to study the potential effects of α-self-irradiation on spent nuclear fuel during storage. The degradation of the thermal properties and microstructure of the samples were monitored using the Laser Flash technique (LAF), X-Ray Diffraction (XRD), and Scanning and Transmission Electron Microscopy (SEM, TEM). The thermal conductivity decreased with a non-linear behaviour as a function of the α-dose. Three clearly different stages in the thermal conductivity degradation could be detected, and saturation was reached at relatively low doses (0.035 dpa). In combination with analyses of the microstrain measured by XRD, and TEM images, these three phases could be attributed to three stages of radiation-induced defect generation and clustering. SEM inspection showed the thermal conductivity degradation cannot be due to loss of integrity or grain boundary opening. The radiation damage produced resulted in the formation of dislocation loops as observed by TEM.

Laser Spinning is a new technique enabling the production of large quantity of very long amorphous ceramic nanofibers. This technique has been successfully tested with different material compositions, probing its capability to produce fibers of inorganic oxides that cannot be produced by any other technique. Precise control of the process allows for the production of amorphous nanofibers of non-ready glass former materials and the unprecedented synthesis of glass nanofibers from very fragile melts. This outcome demonstrates the capability for the synthesis of glass nanofibers with applications in the field of fire retardant fabrics, catalysis or high refractory materials.