Search

Rechargeable aqueous Zn metal batteries are promising systems for grid storage because of their high energy density, low cost, and non-flammability. However, Zn metal anodes have major limitations due to dendrite formation and concurrent water splitting during charge-discharge cycling. Both processes negatively affect coulombic efficiency (CE) and long-term cycling stability. Water-in-salt (WIS) electrolytes were previously proposed to address these challenges, yielding improvements in the cycling stability of Zn metal anodes. While WIS electrolytes help increase CE, they require high amounts of salt (often toxic) and have dramatically increased viscosity, which in turn limit their transport properties, charge-discharge rates, and usability in advanced Zn batteries. In this manuscript, we propose a strategy for simultaneously achieving high CE (>99%), high rate, low cost and reduced environmental footprint. Specifically, we show that by using coordinating anions like acetate a WIS-like Zn coordination environment can be achieved even in relatively dilute conditions, enabling prolonged cycling of Zn metal anodes. Such electrolytes have an order of magnitude higher conductivity and lower viscosity than traditional WIS electrolytes, thus enabling lower overpotentials and higher rate of Zn plating/stripping., Energy & Environmental Science, 16 (5), ISSN:1754-5692, ISSN:1754-5706

In ionic-liquid (IL)-based electrolytes, relevant for current energy storage applications, ion transport is limited by strong ion-ion correlations, generally yielding inverse Haven ratios (ionicities) of below 1. In particular, Li is transported in anionic clusters into the wrong direction of the electric field, requiring compensation by diffusive anion fluxes. Here, we present a concept to exploit ion-ion correlations in concentrated IL electrolytes beneficially by designing organic cations with a Li-coordinating chain.

An in-depth investigation of the solvation structure of the trivalent aluminum cation in Al(OTf)3 solutions reveals major concerns regarding the feasibility of rechargeable aqueous aluminum batteries.

Efficient, rechargeable Mg and Ca batteries Divalent rechargeable metal batteries such as those based on magnesium and calcium are of interest because of the abundance of these elements and their lower tendency to form dendrites, but practical demonstrations are lacking. Hou et al . used methoxyethyl amine chelants in which the ligands attach to the metal atom in more than one place, modulating the solvation structure of the metal ions to enable a facile charge-transfer reaction (see the Perspective by Zuo and Yin). In full battery cells, these components lead to high efficiency and energy density. Theoretical calculations were used to understand the solvation structures. —MSL

The rechargeability of aqueous zinc metal batteries is plagued by parasitic reactions of the zinc metal anode and detrimental morphologies such as dendritic or dead zinc. To improve the zinc metal reversibility, hereby we report a new solution structure of aqueous electrolyte with hydroxyl-ion scavengers and hydrophobicity localized in solvent clusters. We show that although hydrophobicity sounds counterintuitive for an aqueous system, hydrophilic pockets may be encapsulated inside a hydrophobic outer layer, and a hydrophobic anode-electrolyte interface can be generated through the addition of a cation-philic, strongly anion-phobic, and OH

Dynamic covalent chemistry has become an invaluable tool for thedesign and preparation of adaptable yet robust molecular systems.Herein we explore the scope of a largely overlooked dynamiccovalent reaction – amidinium exchange – and report on conditionsthat allow formal amidinium metathesis reactions.

Metallic zinc is an ideal anode due to its high theoretical capacity (820 mAh g−1), low redox potential (−0.762 V versus the standard hydrogen electrode), high abundance and low toxicity. When used in aqueous electrolyte, it also brings intrinsic safety, but suffers from severe irreversibility. This is best exemplified by low coulombic efficiency, dendrite growth and water consumption. This is thought to be due to severe hydrogen evolution during zinc plating and stripping, hitherto making the in-situ formation of a solid–electrolyte interphase (SEI) impossible. Here, we report an aqueous zinc battery in which a dilute and acidic aqueous electrolyte with an alkylammonium salt additive assists the formation of a robust, Zn2+-conducting and waterproof SEI. The presence of this SEI enables excellent performance: dendrite-free zinc plating/stripping at 99.9% coulombic efficiency in a Ti||Zn asymmetric cell for 1,000 cycles; steady charge–discharge in a Zn||Zn symmetric cell for 6,000 cycles (6,000 h); and high energy densities (136 Wh kg−1 in a Zn||VOPO4 full battery with 88.7% retention for >6,000 cycles, 325 Wh kg−1 in a Zn||O2 full battery for >300 cycles and 218 Wh kg−1 in a Zn||MnO2 full battery with 88.5% retention for 1,000 cycles) using limited zinc. The SEI-forming electrolyte also allows the reversible operation of an anode-free pouch cell of Ti||ZnxVOPO4 at 100% depth of discharge for 100 cycles, thus establishing aqueous zinc batteries as viable cell systems for practical applications. A solid–electrolyte interphase that is permeable to Zn(ii) ions but waterproof is formed using an aqueous electrolyte composition. Cycling performances in an anode-free aqueous pouch cell show promise for intrinsically safe energy storage applications.

Aqueous rechargeable zinc metal batteries promise attractive advantages including safety, high volumetric energy density, and low cost; however, such benefits cannot be unlocked unless Zn reversibility meets stringent commercial viability. Herein, we report remarkable improvements on Zn reversibility in aqueous electrolytes when phosphonium-based cations are used to reshape interfacial structures and interphasial chemistries, particularly when their ligands contain an ether linkage. This novel aqueous electrolyte supports unprecedented Zn reversibility by showing dendrite-free Zn plating/stripping for over 6400 h at 0.5 mA cm-2 , or over 280 h at 2.5 mA cm-2 , with coulombic efficiency above 99 % even with 20 % Zn utilization per cycle. Excellent full cell performance is demonstrated with Na2 V6 O16 ⋅1.63 H2 O cathode, which cycles for 2000 times at 300 mA g-1 . The microscopic characterization and modeling identify the mechanism of unique interphase chemistry from phosphonium and its functionalities as the key factors responsible for dictating reversible Zn chemistry.

Widespread commercial adoption of polymer electrolytes for lithium-ion batteries has been hindered by subpar transport properties, namely, ionic conductivities of

Rechargeable Zn metal batteries (RZMBs) may provide a more sustainable and lower-cost alternative to established battery technologies in meeting energy storage applications of the future. However, the most promising electrolytes for RZMBs are generally aqueous and require high concentrations of salt(s) to bring efficiencies toward commercially viable levels and mitigate water-originated parasitic reactions including hydrogen evolution and corrosion. Electrolytes based on nonaqueous solvents are promising for avoiding these issues, but full cell performance demonstrations with solvents other than water have been very limited. To address these challenges, we investigated MeOH as an alternative electrolyte solvent. These MeOH-based electrolytes exhibited exceptional Zn reversibility over a wide temperature range, with a Coulombic efficiency > 99.5% at 50% Zn utilization without cell short-circuit behavior for > 1,800 h. More important, this remarkable performance translates well to Zn || metal-free organic cathode full cells, supporting < 6% capacity decay after > 800 cycles at −40 °C.

A comprehensive understanding of the solid–electrolyte interphase (SEI) composition is crucial to developing high-energy batteries based on lithium metal anodes. A particularly contentious issue concerns the presence of LiH in the SEI. Here we report on the use of synchrotron-based X-ray diffraction and pair distribution function analysis to identify and differentiate two elusive components, LiH and LiF, in the SEI of lithium metal anodes. LiH is identified as a component of the SEI in high abundance, and the possibility of its misidentification as LiF in the literature is discussed. LiF in the SEI is found to have different structural features from LiF in the bulk phase, including a larger lattice parameter and a smaller grain size (

Li metal, with the lowest thermodynamically achievable negative electrochemical potential and the highest specific capacity (3860 mAh g−1), is the ultimate anode choice for Li batteries. However, the highest reported Li plating/stripping Coulombic efficiency (CE) of 99.5% after extensive efforts is still too low for the Li metal-free (all the Li metal in cycling comes from cathode, without anode pre-lithiation) Li metal batteries. The low CE is attributed to both non-uniform Li plating/stripping on the lithiophobic Cu current collector and Li dendrite growth through lithiophilic organic–inorganic solid electrolyte interphase (SEI) formed in carbonate electrolytes. Here, we use a lithiophilic Bismuth graphite blend (Bi–Gr) substrate to replace lithiophobic Cu current collector to seed a uniform Li nucleation, and form a lithiophobic LiF-rich SEI rather than lithiophilic organic-rich SEI to suppress Li dendrite growth. Molecular dynamics simulations reveal the preferential reduction of anions in 2.0 M LiPF6 in tetrahydrofuran/2-methyl tetrahydrofuran (2.0 M LiPF6–mixTHF) electrolyte to generate LiF-rich SEI on plated Li. Bi–Gr substrate and 2.0 M LiPF6–mixTHF electrolyte enable the Li anodes to achieve a record high CE of 99.83% at a high capacity of 1.0 mAh cm−2 and current of 0.5 mA cm−2. The Bi particles serve as dispersed nucleation centers that promote uniform Li deposition with strong adhesion to the substrate to avoid dead Li, while the lithiophobic LiF-rich SEI promotes lateral Li growth and suppresses the vertical Li dendrite growth even at a high current density of 3.0 mA cm−2 and high areal capacities of 3.0 mAh cm−2. The regulation of Li nucleation and growth enables the Li metal-free LiFePO4 full cells to achieve 100 cycles at a practical areal capacity of >2.0 mAh cm−2. This manuscript highlights the benefits of simultaneous substrate design to improve Li nucleation and electrolyte design to promote lithiophobic SEI growth, enabling a promising and practical route Li metal-free Li metal batteries.

Rechargeable zinc metal batteries (RZMBs) offer a compelling complement to existing lithium ion and emerging lithium metal batteries for meeting the increasing energy storage demands of the future. Multiple recent reports have suggested that optimized electrolytes resolve a century-old challenge for RZMBs by achieving extremely reversible zinc plating/stripping with Coulombic efficiencies (CEs) approaching 100%. However, the disparity among published testing methods and conditions severely convolutes electrolyte performance comparisons. The lack of rigorous and standardized protocols is rapidly becoming an impediment to ongoing research and commercialization thrusts. This Perspective examines recent efforts to improve the reversibility of the zinc metal anode in terms of key parameters, including CE protocols, plating morphology, dendrite formation and long-term stability. Then we suggest the most appropriate standard protocols for future CE determination. Finally, we envision future strategies to improve zinc/electrolyte stability so that research efforts can be better aligned towards realistic performance targets for RZMB commercialization. Zinc metal batteries (ZMBs) provide a promising alternative to lithium metal batteries but share the formidable challenges in reversibility. The authors discuss the key performance metrics of ZMBs and propose a protocol to assess the true reversibility of zinc metal anodes.

Polysulfide shuttle effects, active material losses, formation of resistive surface layers, and continuous electrolyte consumption create a major barrier for the lightweight and low-cost lithium-sulfur (Li-S) battery adoption. Tuning electrolyte composition by using additives and most importantly by substantially increasing electrolyte molarity was previously shown to be one of the most effective strategies. Contrarily, little attention has been paid to dilute and super-diluted LiTFSI/DME/DOL/LiNO3 based-electrolytes, which have been thought to aggravate the polysulfide dissolution and shuttle effects. Here we challenge this conventional wisdom and demonstrate outstanding capabilities of a dilute (0.1 mol L-1 of LiTFSI in DME/DOL with 1 wt. % LiNO3) electrolyte to enable better electrode wetting, greatly improved high-rate capability, and stable cycle performance for high sulfur loading cathodes and low electrolyte/sulfur ratio in Li-S cells. Overall, the presented study shines light on the extraordinary ability of such electrolyte systems to suppress short-chain polysulfide dissolution and polysulfide shuttle effects., This work was largely supported by the National Key R&D Research Program of China (No. 2018YFB0905400),the Innovation-Driven Project of Central South University (No.2019CX033), the National Key R&D Research Program of China (No. 2018YFB0905400), the National Natural Science Foundation of China (Nos. U1910210, 51904344, 51925207, 51872277), and the DNL cooperation Fund, CAS (DNL180310), and the Fundamental Research Funds for the Central Universities (Wk2060140026, WK2060000009). The modeling part of the work performed at ARL was supported as part of the Joint Center for Energy Storage Research (JCESR), an Energy Innovation Hub funded by the U.S. Department of Energy, Office of Science, Basic Energy Sciences.

Lithium batteries with Si, Al or Bi microsized (>10 µm) particle anodes promise a high capacity, ease of production, low cost and low environmental impact, yet they suffer from fast degradation and a low Coulombic efficiency. Here we demonstrate that a rationally designed electrolyte (2.0 M LiPF6 in 1:1 v/v mixture of tetrahydrofuran and 2-methyltetrahydrofuran) enables 100 cycles of full cells that contain microsized Si, Al and Bi anodes with commercial LiFePO4 and LiNi0.8Co0.15Al0.05O2 cathodes. Alloy anodes with areal capacities of more than 2.5 mAh cm−2 achieved >300 cycles with a high initial Coulombic efficiency of >90% and average Coulombic efficiency of >99.9%. These improvements are facilitated by the formation of a high-modulus LiF–organic bilayer interphase, in which LiF possesses a high interfacial energy with the alloy anode to accommodate plastic deformation of the lithiated alloy during cycling. This work provides a simple yet practical solution to current battery technology without any binder modification or special fabrication methods. Chunsheng Wang and colleagues develop an electrolyte strategy to enable the use of commercially available microsized alloys, such as Si–Li, as high-performance battery anodes. They ascribe its success to the formation of robust LiF-rich layers as the solid–electrolyte interface.

With high energy density and improved safety, rechargeable battery chemistries with a zinc (Zn) metal anode offer promising and sustainable alternatives to those based on lithium metal or lithium ion intercalation/alloying anode materials; however, the poor electrochemical reversibility of Zn plating/stripping, induced by parasitic reactions with both aqueous and non-aqueous electrolytes, presently limits the practical appeal of these systems1. Although recent efforts in rechargeable Zn metal batteries (RZMBs) have achieved certain advancements in Zn metal reversibility2,3, as quantified by the Coulombic efficiency (CE), a standard protocol for CE has not been established, and results across chemistries and systems are often conflicting. More importantly, there is still an insufficient understanding regarding the critical factors dictating Zn reversibility. In this work, a rigorous, established protocol for determining CE of lithium metal anodes4 is transplanted to the Zn chemistry and is used for systematically examining how a series of factors including current collector chemistry, current density, temperature, and the upper voltage limit during stripping affect the measured reversibility of different Zn electrolytes. With support from density functional theory calculations, this standardized Zn CE protocol is then leveraged to identify an important correlation between electrolyte solvation strength toward Zn2+ and the measured Zn CE in the corresponding electrolyte, providing new guidance for future development and evaluation of Zn electrolytes. Figure 1 shows a schematic of proposed method, including initial results for some of the most promising Zn electrolytes reported in the literature. The capability of supporting Zn plating/stripping is differentiated clearly among these selected Zn electrolytes here. Reference 1. Blanc, L. E., Kundu, D. & Nazar, L. F. Scientific Challenges for the Implementation of Zn-Ion Batteries. Joule 4, 771–799 (2020). 2. Wang, F. et al. Highly reversible zinc metal anode for aqueous batteries. Nat. Mater. 17, 543–549 (2018) 3. Naveed, A., Yang, H., Yang, J., Nuli, Y. & Wang, J. Highly Reversible and Rechargeable Safe Zn Batteries Based on a Triethyl Phosphate Electrolyte. Angew. Chemie Int. Ed. 58, 2760–2764 (2019). 4. Adams, B. D., Zheng, J., Ren, X., Xu, W. & Zhang, J.-G. Accurate Determination of Coulombic Efficiency for Lithium Metal Anodes and Lithium Metal Batteries. Adv. Energy Mater. 8, 1702097 (2018). Figure 1

A water-in-salt electrolyte (WiSE) offers an electrochemical stability window much wider than typical aqueous electrolytes but still falls short in accommodating high-energy anode materials, mainly...

We report a systematic diffraction study of two “water-in-salt” electrolytes and a “water-in-bisalt” electrolyte combining high-energy X-ray diffraction (HEXRD) with polarized and unpolarized neutron diffraction (ND) on both H(2)O and D(2)O solutions. The measurements provide three independent combinations of correlations between the different pairs of atom types that reveal the short- and intermediate-range order in considerable detail. The ND interference functions show pronounced peaks around a scattering vector Q ∼ 0.5 Å(−1) that change dramatically with composition, indicating significant rearrangements of the water network on a length scale around 12 Å. The experimental results are compared with two sets of Molecular Dynamics (MD) simulations, one including polarization effects and the other based on a non-polarizable force field. The two simulations reproduce the general shapes of the experimental structure factors and their changes with concentration, but differ in many detailed respects, suggesting ways in which their force fields might be modified to better represent the actual systems.

A new class of electrolytes have been reported, hybridizing aqueous with non-aqueous solvents, which combines non-flammability and non-toxicity characteristics of aqueous electrolytes with the superior electrochemical stability of non-aqueous systems. Here, we report measurements of the structure of an electrolyte composed of an equal-mass mixture of 21 m LiTFSI-water and 9 m LiTFSI-dimethyl carbonate using high-energy x-ray diffraction and polarized neutron diffraction with isotope substitution. Neutron structure factors from partially and fully deuterated samples exhibit peaks at low scattering vector Q that we ascribe to long-range correlations involving both solvent molecules and TFSI− anions. We compare both sets of measurements with results of molecular dynamics simulations based on a polarizable force field. The structures derived from simulations are generally in agreement with those measured, except that neutron structure factors predicted for two partially deuterated samples show very intense scattering increasing up to the low- Q limit of simulation, indicating a partial segregation between the two solvents not observed in experimental measurements.

The formation of solid-electrolyte interphase (SEI) in "water-in-salt" electrolyte (WiSE) expands the electrochemical stability window of aqueous electrolytes beyond 3.0 V. However, the parasitic hydrogen evolution reaction that drives anode corrosion, cracking, and the subsequent reformation of SEI still occurs, compromising long-term cycling performance of the batteries. To improve cycling stability, an unsaturated monomer acrylamide (AM) is introduced as an electrolyte additive, whose presence in WiSE reduces its viscosity and improves ionic conductivity. Upon charging, AM electropolymerizes into polyacrylamide, as confirmed both experimentally and computationally. The in situ polymer constitutes effective protection layers at both anode and cathode surfaces, and enables LiMn2 O4 ||L-TiO2 full cells with high specific capacity (157 mAh g-1 at 1 C), long-term cycling stability (80% capacity retention within 200 cycles at 1 C), and high rate capability (79 mAh g-1 at 30 C). The in situ electropolymerization found in this work provides an alternative and highly effective strategy to design protective interphases at the negative and positive electrodes for high-voltage aqueous batteries of lithium-ion or beyond.

The electrolytes of the today omnipresent lithium-ion batteries (LIBs) have for more than 25 years been based upon 1 M LiPF6 in a 50:50 EC:DMC mixture—commonly known as LP30. The success of the basic design of the LP30 electrolyte, with many variations and additions made over the years, is unchallenged. Yet, some molecular level fundamentals of LP30 are surprisingly elusive: the structure of the first solvation shell of the Li+ cation is still a topic of current debate; the details of the dynamics are not fully understood; the interpretation of structural and dynamic properties is highly dependent on the analysis methods used; the contributions by different species to the ion transport and the energetics involved are not established. We here apply dynamic structure discovery analysis as implemented in CHAMPION to molecular dynamics simulation trajectories to bring new light on the structure and dynamics within LP30 and especially the (Li+) ion transport to rationalize further development of LIB electrolytes.

The bis(fluorosulfonyl)imide anion N(SO2F)2 − (i.e., FSI−) (also referred to as bis(fluorosulfonyl)amide (i.e., FSA−) and imidodi(sulphuryl fluoride)) has attracted tremendous interest in recent years for its utility in both lithium salts and ionic liquids for battery electrolyte applications. To facilitate the understanding of the characteristics of this anion, crystal structures are reported here for the uncoordinated anion in LiFSI-based solvates with cryptand CRYPT-222 and tetraglyme (G4). These crystalline solvates were analyzed by Raman spectroscopy to aid in assigning the Raman bands to the modes of ion coordination found in liquid electrolytes. These structures, as well as a thorough review of other relevant crystallographic data, provide insights into the rather remarkable properties of the FSI− anion with regard to solvate formation and electrolyte properties.

Advances in supramolecular chemistry are often underpinned by the development of fundamental building blocks and methods enabling their interconversion. In this work, we report the use of an underexplored dynamic covalent reaction for the synthesis of stimuli-responsive [2]rotaxanes. The formamidinium moiety lies at the heart of these mechanically interlocked architectures, because it enables both dynamic covalent exchange and the binding of simple crown ethers. We demonstrated that the rotaxane self-assembly follows a unique reaction pathway and that the complex interplay between crown ether and thread can be controlled in a transient fashion by addition of base and fuel acid. Dynamic combinatorial libraries, when exposed to diverse nucleophiles, revealed a profound stabilizing effect of the mechanical bond as well as intriguing reactivity differences between seemingly similar [2]rotaxanes.

In this work, we demonstrate that intrinsically altering the reaction pathway of a sulfur-based cathode with designed additional redox activities could simultaneously suppress polysulfide shuttling...

The solid–electrolyte interphase (SEI) dictates the performance of most batteries, but the understanding of its chemistry and structure is limited by the lack of in situ experimental tools. In this work, we present a dynamic picture of the SEI formation in lithium-ion batteries using in operando liquid secondary ion mass spectrometry in combination with molecular dynamics simulations. We find that before any interphasial chemistry occurs (during the initial charging), an electric double layer forms at the electrode/electrolyte interface due to the self-assembly of solvent molecules. The formation of the double layer is directed by Li+ and the electrode surface potential. The structure of this double layer predicts the eventual interphasial chemistry; in particular, the negatively charged electrode surface repels salt anions from the inner layer and results in an inner SEI that is thin, dense and inorganic in nature. It is this dense layer that is responsible for conducting Li+ and insulating electrons, the main functions of the SEI. An electrolyte-permeable and organic-rich outer layer appears after the formation of the inner layer. In the presence of a highly concentrated, fluoride-rich electrolyte, the inner SEI layer has an elevated concentration of LiF due to the presence of anions in the double layer. These real-time nanoscale observations will be helpful in engineering better interphases for future batteries. An operando mass spectrometry technique, along with molecular dynamics simulations, unveils the evolution of the solid–electrolyte interphase chemistry and structure in lithium-ion batteries during the first cycle.

Summary As a legacy left behind by classical analytical electrochemistry in pursuit of ideal electrodics, and classical physical electrochemistry in pursuit of the most conductive ionics, the study of non-aqueous electrolytes has been historically confined within a narrow concentration regime around 1 molarity (M). This confinement was breached in recent years when unusual properties were found to arise from the excessive salt presence, which often bring benefits to electrochemical, thermal, transport, interfacial, and interphasial properties that are of significant interest to the electrochemical energy storage community. This article provides an overview on this newly discovered and under-explored realm, with emphasis placed on their applications in rechargeable batteries.