Search

The contact line movement, advancing and receding, of the distilled water droplet was studied on the polished and laser patterned aluminum surfaces. The obtained dependences of the dynamic contact angles on the contact line speed were fitted by the combined theory consisting of molecular-kinetic and hydrodynamic theories. Results obtained on laser patterned surface are found to fit better to the theory in comparison with polished surface. The assumption was made that this result is connected with the low contact angle hysteresis on the patterned surface compared to the polished one. It means that combined theory does not consider the contact angle hysteresis.

The influence of drop irrigation of the condensation part on the thermosyphon operational mode was studied experimentally. The temperature and pressure fall was found in the internal space of the upper chamber after applying the liquid on the upper wall of the thermosyphon. The temperature difference along the height of vapor channel increases and the effective resistance decreases. When complete evaporation of liquid droplets from thermosyphon, it returns to the quasi-stationary mode of operation.

Paper presents the experimental results of mass evaporation rate from ethanol layer surface into a moving in parallel way air flow. Dependences of the mass evaporation rate on the gas velocity, temperature difference between gas and liquid layer, and liquid layer thickness were obtained. The assumption about the formation of the concentration boundary layer at the interface was made. It is found that with increasing the gas flow velocity the gradient of vapor concentration in the gas phase increases; as a result the evaporation rate rises. When changing the liquid layer thickness, the local maximum of evaporation rate was observed, but for 2 mm thickness layer two maxima were found. Probably, it is due the appearance of unstable structures on the liquid surface.

The paper presents an analysis of known dependencies for determining the critical heat flux density in diphasic thermosyphons. The critical heat flux density for the created experimental model of thermosyphon were calculated on the basis of the theoretical contributions of 1) the occurrence of a “flooding” regime in a thermosyphon characterized by a disturbance of the hydrodynamic stability of the phase interface and the entrainment of the liquid phase by the gas flow; 2) the mutual influence of gravitational forces and surface tension; 3) S.S. Kutateladze hydrodynamic theory of the heat transfer crisis during boiling. It is found that the existing theoretical contributions which can be used to calculate the critical heat flux density and subsequently determine the minimum filling ratio of a thermosyphon are conditionally applicable.

The concept of conducting the experiments for studying thin liquid film boiling and evaporation was developed. Implementing this conception on developed experimental setup, we will obtain the data on the change of liquid film thickness in thermosiphon and temperature distribution in the liquid film, also the evaporation rate of liquid film and heat transfer coefficient change will be calculated using the measured values in the experiment. Three series of preliminary experiment were conducted. As a result, the main influencing factors and their values were defined.

The investigation of dynamic contact angle between distilled water droplet and superhydrophobic surface was conducted experimentally. To obtain the values of contact angle during spreading, shadow method was implemented. We used Schlieren method to control the droplet symmetry. The droplet was formed on the surface by syringe pump using nontraditional bottom-up methodology. The drop growth rate was varied by the syringe pump from 0.005 ml/s to 0.32 ml/s. DCA versus drop volume was obtained for different values of the drop growth rate. Some features of spreading on superhydrophobic surface were pointed out. Interestingly, that the dynamic contact angle increases during all stages previously selected for copper substrates (1 – droplet formation; 2 – spreading; 3 – formation of the equilibrium contact angle). However, at the droplet growth rate 0.005ml/s we found decrease in the contact angle. The droplet was found to take a shape close to a spherical cap in the range of the drop growth rate 0.005 ml/s – 0.16 ml/s. At higher rates (0.32 ml/s and higher) liquid splashing was observed.

The characteristics of water droplet heating and evaporation on structured hydrophobic and hydrophilic surfaces in the range of static contact angles from 73° to 155° were studied experimentally using high-speed video recording. Two fundamentally different technologies for applying coatings on a metal surface were used in comparison with the results on a polished surface. Microscopic studies were conducted to identify the features of the formed coatings. The wetting properties were characterized by means of the static contact angle and the contact angle hysteresis: on polished surface No. 1 (contact angle—73°, hysteresis—11°), on structured surface No. 2 (contact angle—125°, hysteresis—9°), and on structured surface No 3 (contact angle—155°, hysteresis—7°). The experimental dependences of the droplet evaporation rate on the different surfaces under normal conditions (ambient air temperature—293 K, atmospheric pressure, humidity—35%) were obtained. The evaporation regimes of droplets on the surfaces under study were identified. Water droplets evaporated in the pinning mode on surfaces No. 1 and No. 2. When a water droplet evaporated on surface No 3, the droplet was in the constant contact angle regime for ≈90% of its lifetime. Based on the experimental data obtained, a two-dimensional model of conjugate heat and mass transfer was developed, which describes the heating and evaporation of a liquid droplet on structured hydrophobic and hydrophilic surfaces at a wide range of contact angles. Satisfactory agreement was obtained between the numerical simulation results and experimental data. Using the model, the fields of temperature, concentration and other key characteristics were established at different points in time. Recommendations for its application in the development of gas–vapor–droplet applications were formulated. [ABSTRACT FROM AUTHOR]