Search

Your search keyword '"Oskirko, V."' showing total 35 results
Start Over Author "Oskirko, V."
35 results on '"Oskirko, V."'

32. Voluminous high-density plasma generator based on high-current pulsed magnetron discharge

Author

Sochugov, Nikolay S., Zakharov, Alexander N., Oskirko, V. O., Semenov, Vladimir A., Semenyuk, N. S., Kozyrev, Andrey V., Томский государственный университет Физический факультет Кафедра физики плазмы, and Томский государственный университет Физический факультет Научные подразделения ФФ

Subjects
плазменно-иммерсионная обработка, магнетронные распылительные системы, магнетронные разряды, физика плазмы
Published
2012

33. Properties of TiAlN Coatings Obtained by Dual-HiPIMS with Short Pulses.

Author

Grenadyorov A, Oskirko V, Zakharov A, Oskomov K, Rabotkin S, Semenov V, Solovyev A, and Shmakov A

Abstract

The paper focuses on the dual high-power impulse magnetron sputtering of TiAlN coatings using short pulses of high power delivered to the target. The surface morphology, elemental composition, phase composition, hardness, wear resistance, and adhesive strength of TiAlN coatings with different Al contents were investigated on WC-Co substrates. The heat resistance of the TiAlN coating was determined with synchrotron X-ray diffraction. The hardness of the TiAlN coating with a low Al content ranged from 17 to 30 GPa, and its wear rate varied between 1.8∙10 -6 and 4.9∙10 -6 mm 3 ·N -1 ·m -1 depending on the substrate bias voltage. The HF1-HF2 adhesion strength of the TiAlN coatings was evaluated with the Daimler-Benz Rockwell C test. The hardness and wear rate of the Ti 0.61 Al 0.39 N coating were 26.5 GPa and 5.2∙10 -6 mm 3 ·N -1 ·m -1 , respectively. The annealing process at 700 °C considerably worsened the mechanical properties of the Ti 0.94 Al 0.06 N coating, in contrast to the Ti 0.61 Al 0.39 N coating, which manifested a high oxidation resistance at annealing temperatures of 940-950 °C.

Published
2023
Full Text
View/download PDF

34. (Cr 1-x Al x )N Coating Deposition by Short-Pulse High-Power Dual Magnetron Sputtering.

Author

Grenadyorov A, Oskirko V, Zakharov A, Oskomov K, and Solovyev A

Abstract

The paper deals with the (Cr 1-x Al x )N coating containing 17 to 54 % Al which is deposited on AISI 430 stainless steel stationary substrates by short-pulse high-power dual magnetron sputtering of Al and Cr targets. The Al/Cr ratio in the coating depends on the substrate position relative to magnetrons. It is shown that the higher Al content in the (Cr 1-x Al x )N coating improves its hardness from 17 to 28 GPa. Regardless of the Al content, the (Cr 1-x Al x )N coating manifests a low wear rate, namely (4.1-7.8) × 10 -9 and (3.9-5.3) × 10 -7 mm 3 N -1 m -1 in using metallic (100Cr6) and ceramic (Al 2 O 3 ) counter bodies, respectively. In addition, this coating possesses the friction coefficient 0.4-0.7 and adhesive strength quality HF1 and HF2 indicating good interfacial adhesion according to the Daimler-Benz Rockwell-C adhesion test.

Published
2022
Full Text
View/download PDF

Catalog

Books, media, physical & digital resources
See catalog results