Search

Strong anisotropy of seismic velocity in the Earth's crust poses serious challenges for seismic imaging. Where in situ seismic properties are not available, the anisotropy can be determined from velocity analysis of surface and borehole seismic profiles. This is well established for dense, long-offset reflection seismic data. However, it is unknown how applicable this approach is for sparse seismic reflection data with low fold and short offsets in anisotropic metamorphic rocks. Here, we show that anisotropy parameters can be determined from a sparse 3-D data set at the COSC-1 borehole site in the Swedish Caledonides and that the results agree well with the seismic anisotropy parameters determined from seismic laboratory measurements on core samples. Applying these anisotropy parameters during 3-D seismic imaging improves the seismic image of the high-amplitude reflections especially in the vicinity of the lower part of the borehole. Strong reflections in the resulting seismic data show good correlation with the borehole-derived lithology. Our results aid the interpretation and extrapolation of the seismic stratigraphy of the Lower Seve Nappe in Jamtland and other parts in the Caledonides.

Continental collision causes deformation in the crust along shear zones. However, the physical and chemical conditions at which these zones operate and the deformation processes that enable up to hundreds of km of tectonic transport are still unclear because of the depth at which they occur and the challenges in imaging them. Ancient exhumed collision zones allow us to investigate these processes much better, for example at the COSC‐1 borehole in the central Scandinavian Caledonides. This study combines data from the COSC‐1 borehole with different seismic measurements to provide constraints on the spatial lithological and textural configuration of the Seve Nappe Complex. This is one of the few studies that shows that core‐log‐seismic integration in metamorphic rocks allows to identify the spatial distribution of major lithological units. Especially gamma ray logs in combination with density data are powerful tools to distinguish between mafic and felsic lithologies in log‐core correlation. Our results indicate that reflections along the borehole are primarily caused by compositional rather than textural changes. Reflections in the Seve Nappe Complex are not as distinct as in greater depths but continuous and several of them can be linked to magmatic intrusions, which have been metamorphically overprinted. Their setting indicates that the Seve Nappe Complex consists of the remnants of a volcanic continental margin. Our results suggest that ductile‐deformed middle crustal reflectivity is primarily a function of pre‐orogenic lithological variations which has to be considered when deciphering mountain building processes. Plain Language Summary Areas where continents collide experience different kind of deformation. However, these processes and the conditions at which they take place are difficult to study because of the great depth at which they occur. Former collision zones that are closer to the surface these days allow the investigation of these processes much better

Metamorphic and deformed rocks in thrust zones show particularly high seismic anisotropy causing challenges for seismic imaging and interpretation. A good example is the Seve Nappe Complex in central Sweden, an old exhumed orogenic thrust zone that is characterized by a strong but incoherent seismic reflectivity and considerable seismic anisotropy. However, only little is known about their origin in relation to composition and structural influences on measurements at different seismic scales. Here, we present a new integrative study of cross‐scale seismic anisotropy analyses combining mineralogical composition, microstructural analyses and seismic laboratory experiments from the COSC‐1 borehole, which sampled a 2.5 km‐deep section of metamorphic rocks deformed in an orogenic root now preserved in the Lower Seve Nappe. While there is strong crystallographic preferred orientation in most samples in general, variations in anisotropy depend mostly on bulk mineral composition and dominant core lithology as shown by a strong correlation between these. This relationship enables to identify three distinct seismic anisotropy facies providing a continuous anisotropy profile along the borehole. Moreover, comparison of laboratory seismic measurements and electron‐backscatter diffraction data reveals a strong scale‐dependence, which is more pronounced in the highly deformed, heterogeneous samples. This highlights the need for comprehensive cross‐validation of microscale anisotropy analyses with additional lithological data when integrating seismic anisotropy over seismic scales.

A methodology for a comprehensive probabilistic tsunami hazard analysis is presented for the major sources of tsunamis (seismic events, landslides, and volcanic activity) and preliminarily applied in the Gulf of Naples (Italy). The methodology uses both a modular procedure to evaluate the tsunami hazard and a Bayesian analysis to include the historical information of the past tsunami events. In the urn:x-wiley:jgrc:media:jgrc23818:jgrc23818-math-0001 the submarine earthquakes and the submarine mass failures are initially identified in a gridded domain and defined by a set of parameters, producing the sea floor deformations and the corresponding initial tsunami waves. Differently volcanic tsunamis generate sea surface waves caused by pyroclastic density currents from Somma‐Vesuvius. In the urn:x-wiley:jgrc:media:jgrc23818:jgrc23818-math-0002 the tsunami waves are simulated and propagated in the deep sea by a numerical model that solves the shallow water equations. In the urn:x-wiley:jgrc:media:jgrc23818:jgrc23818-math-0003 the tsunami wave heights are estimated at the coast using the urn:x-wiley:jgrc:media:jgrc23818:jgrc23818-math-0004's amplification law. The selected tsunami intensity is the wave height. In the urn:x-wiley:jgrc:media:jgrc23818:jgrc23818-math-0005 the probabilistic tsunami analysis computes the long‐term comprehensive Bayesian probabilistic tsunami hazard analysis. In the prior analysis the probabilities from the scenarios in which the tsunami parameter overcomes the selected threshold levels are combined with the spatial, temporal, and frequency‐size probabilities of occurrence of the tsunamigenic sources. The urn:x-wiley:jgrc:media:jgrc23818:jgrc23818-math-0006 probability density functions are integrated with the urn:x-wiley:jgrc:media:jgrc23818:jgrc23818-math-0007 derived from the historical information based on past tsunami data. The urn:x-wiley:jgrc:media:jgrc23818:jgrc23818-math-0008 probability density functions are evaluated to produce the

As part of the ICDP priority program “Collisional Orogeny of the Scandinavian Caledonides (COSC)” we are investigating the geophysical properties of the rocks from the Seve Nappe Complex (SNC) using the COSC-1 borehole (Sweden). This project has two main objectives. The first, geological aim is to establish a high-resolution seismic stratigraphy applying Core-Log-Seismic-Integration (CLSI) to a metamorphic setting to improve our understanding of the tectonic and structural geological processes that led to the formation of the SNC and, in particular, how shear stress was partitioned and how it affected the geophysical properties. The second, methodological objective aims at learning how the CLSI techniques can be applied for metamorphic rocks although they have been developed mainly for hydrocarbon reservoirs in lithified sediment rocks. Here, we use information from two sets of wireline logs and tie them to a 2D and 3D seismic surveys from the SNC, a multi-azimuthal walkaway vertical seismic profile, and a high-resolution zero-offset vertical seismic profile, and combine them through Log-Seismic-Integration (LSI). From density and sonic information we have generated synthetic seismograms and compared them to zero offset seismic traces and traces from the processed surface 3D seismic data that were extracted at the location of the borehole. As expected, the results show significant deviations between synthetic and measured seismograms due to seismic wave propagation artefacts, noise both in the seismic and in the downhole logging data, imperfect coupling of the tools in the boreholes and uncertainty in the depth measurements during logging as well as anisotropy in the seismic velocities. Nevertheless, we identify a number of prominent reflections that can be linked e.g. to amphibolite zones as well as to measured seismograms which will allow us to extrapolate the lithology from the borehole. In order to reveal physical properties of the methamorphic setting the next

The Stress Map of the Mediterranean and Central Europe 2016 displays 5011 A-C quality stress data records of the upper 40 km of the Earth’s crust from the WSM database release 2016 (Heidbach et al, 2016, http://doi.org/10.5880/WSM.2016.001). Focal mechanism solutions determined as being potentially unreliable (labelled as Possible Plate Boundary Events in the database) are not displayed. Further detailed information on the WSM quality ranking scheme, guidelines for the various stress indicators, and software for stress map generation and the stress pattern analysis is available at www.world-stress-map.org.