Search

These days, because power quality (PQ) issues are costing industrial customers a lot of money, both electrical utilities and end-users are paying a lot of attention to them. The most significant and frequent PQ concerns for sensitive loads are voltage sag and swell. This manuscript proposes an optimization technique for enhancing the control system of a unified power quality conditioner (UPQC) connected solar photovoltaic system in the distributed generation system. The proposed strategy is the archerfish hunting optimizer (AHO). The objective of the AHO approach is to optimizing UPQC operation in distribution systems, focusing on targeted power quality enhancement. The optimal control pulses are produced by the series active power filter and the shunt active power filter, depending on the load-side and source circumstances. During the load variation states the AHO technique manages the power loss, total harmonic distortion (THD), and voltage instability issue respectively. The performance of the AHO methodology is carried out on the MATLAB platform and compared with existing methods, like particle swarm optimization (PSO), latent semantic analysis (LSA), and ant-lion optimizer (ALO). The existing methods THD are 6.35%, 7.85%, and 9.19%. The proposed method of THD is 4.22%. From the outcome, it concluded that the proposed method based on the THD is low contracted to present techniques. [ABSTRACT FROM AUTHOR]

ABSTRACT This paper presents a methodology to estimate, in the design stage, the total harmonic distortion of the current injected into the power grid by two‐stage voltage source inverters (VSI). As such inverters operate in a closed loop, the quality of the grid current is highly dependent on the dynamics of the control loops. Thus, it is necessary to focus on an approach to model the behavior of the grid current considering the closed‐loop disturbances. The proposed approach allows deriving an equation to predict the behavior of the current injected into the grid and estimate its harmonic distortion, becoming an important tool for optimal design of grid‐connected inverters. To validate the accuracy of the developed methodology, experimental results are presented in different operating scenarios. [ABSTRACT FROM AUTHOR]

In this research, we investigate the power quality of the grid where an Electric Arc Furnace (EAF) with a very high load operates. An Electric Arc Furnace (EAF) is a highly nonlinear load that uses very high and variable currents, causing major power quality issues such as voltage sags, flickers, and harmonic distortions. These disturbances produce electrical grid instability, affect the operation of other equipment, and require strong mitigation measures to reduce their impact. To investigate these issues, data are collected from the Point of Common Coupling where the Electric Arc Furnace is fed. The following three main factors are identified for evaluating power quality: apparent power, active and reactive power, and distorted power. Along with these powers, Total Harmonic Distortion, an important indicator of power quality, is calculated. These data are collected during the full process of producing a complete steel batch. To create a Deep Neural Network that can model and forecast power quality parameters, a network is developed using LSTM layers, Convolutional Layers, and GRU Layers, all of which demonstrate good prediction performance. The results of the prediction models are examined, as well as the primary metrics characterizing the prediction, using the following: MAE, RMSE, R-squared, and sMAPE. Predicting active and reactive power and Total Harmonic Distortion (THD) proves useful for anticipating power quality problems in an Electric Arc Furnace (EAF). By reducing the EAF's impact on the power system, accurate predictions will anticipate and minimize disturbances, optimize energy consumption, and improve grid stability. This research's principal scientific contribution is the development of a hybrid deep neural network that integrates Convolutional Neural Networks (CNNs), Long Short-Term Memory (LSTM), and Gated Recurrent Unit (GRU) layers. This deep neural network was designed to predict power quality metrics, including active power, reactive power, distortion power, and Total Harmonic Distortion (THD). The proposed methodology indicates an important step in improving the accuracy of power quality forecasting for Electric Arc Furnaces (EAFs). The hybrid model's ability for analyzing both time-series data and complex nonlinear patterns improves its predictive accuracy compared to traditional methods. [ABSTRACT FROM AUTHOR]

This paper proposes goal-function-based decentralized control of microgrids. In addition to being an instrument for maintaining the grid voltage and frequency stability, each grid-tie inverter generates a current component with the aim of compensating for voltage distortion in the node where it is connected. The designed goal-function does not need to rely on the assumption that a microgrid is dominantly inductive or resistive to derive its control law, as is mostly the case with the droop-based approach. The priorities of the proposed scheme can be adjusted according to user preferences. In addition, the control algorithm is independent of network topology, can be applied in both islanded and non-islanded microgrids, and secure system scalability. The proposed method is verified by detailed simulations. [ABSTRACT FROM AUTHOR]

Copyright of Przegląd Elektrotechniczny is the property of Przeglad Elektrotechniczny and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

The effects of harmonics, interharmonics, and subharmonics on low-voltage distribution networks, leading to a deterioration in electrical power quality, have become more evident in recent years. The main harmonic sources are power electronic devices due to their implicit nonlinearity. Interharmonic and subharmonic components are mainly caused by a lack of synchronization between the grid frequency and the switching frequency of the power converters. This can be caused by asynchronous modulated devices, or more commonly by fluctuations in the fundamental grid frequency. Interharmonic currents cause interharmonic voltage distortions that affect grid-synchronized or frequency-dependent systems. The IEC-61000-4-7 proposes a general guide on harmonics, interharmonic measurements, and instrumentation in current supply systems. However, the techniques proposed in the standard are intended for measurement and do not enable a precise identification of the interharmonic components in a signal. This work proposes new definitions for the spectral energy aggrupation to improve signal component detection for the IEC standard. Furthermore, an adaptive Kalman filter algorithm is developed that enables the exact identification in real time of the frequency, amplitude, and phase of these components. The proposed system will become the basis for the implementation of a new range of measurement systems that provide improved accuracy and real-time operation. The work is supported by simulated results analysing various scenarios (including transients after changes in harmonic content in the grid voltage) that demonstrate the effectiveness of the proposed method. [ABSTRACT FROM AUTHOR]

This study aims to ameliorate the contribution capability of doubly-fed induction generator (DFIG) to participate in standalone microgrid operation. The islanded microgrid consists of a solar photovoltaic array for solar energy conversion and battery energy storage in addition to DFIG-based wind energy conversion system. Using a simplified control approach, the study describes multi-mode operation of a DFIG-based AC/DC microgrid using a stator-side solid-state transition switch (SSTS). Using SSTS operation, the DFIG stator can be seamlessly disconnected and reconnected from the point of common coupling without interrupting power to the loads in the microgrid. Additionally, non-ideal AC loads can be handled efficiently without the need for computationally exhaustive approaches to enhance stator voltages and currents. [ABSTRACT FROM AUTHOR]

This article proposes a voltage compensation control strategy for the distribution network based on the unified power quality conditioner (UPQC) with battery energy storage systems (BESS) to achieve comprehensive management of the power quality and improve the system dynamic responses. Specifically, aiming at that amplitude and phase jump of the terminal voltage, a capacity configuration compensation scheme is proposed to achieve voltage vector compensation. The series converter is designed to compensate for the amplitude and phase of the load voltage. The parallel converter is designed to realize power compensation and ensure that the grid voltage and current are sinusoidal and in phase. A voltage control approach based on the nonlinear disturbance observer (NDO) is developed for BESS to stabilize the DC bus voltage and improve the anti-interference performance of the current. An NDO is designed to accomplish current disturbance tracking and provide disturbance feedforward compensation. Simulations validate that the proposed approach is effective and feasible. [ABSTRACT FROM AUTHOR]

ABSTRACT This study delves into the advancements, challenges, and opportunities in the solar grid technology, emphasizing its integration into the existing power infrastructure. The proposed ML‐FOGI (multilayer fourth‐order generalized integrator) algorithm presents a promising solution for modern grid synchronization requirements, addressing challenges posed by the integration of renewable energy into the distributed generation. This technology enhances system robustness and dynamic response, particularly in weak distribution grids characterized by voltage distortions and imbalances. This innovative approach enhances system stability and performance, particularly in polluted grid conditions. Through MATLAB/Simulink modelling and experimental validation, the effectiveness of the proposed control strategy is investigated across diverse testing conditions. Emphasizing the significant role of the control strategy in enhancing power quality and grid stability in the solar photovoltaic systems, this research underscores the importance of robust and adaptive control mechanisms for optimizing performance and ensuring grid reliability in modern microgrid. This study delves into this complex issue of working of the grid connected photovoltaic (GCPV) system, emphasizing the importance of balanced unit templates and a stable DC link voltage with unpredictable grid harmonics. This research aims to enhance the resilience of solar PV systems against grid disturbances by drawing inspiration from the adaptable nature of ADALINE filters and adhering to the IEEE519 requirements. This study employs OPAL‐RT's resilient experimental configuration. [ABSTRACT FROM AUTHOR]

The increasingly widespread use of new power equipment has brought new disturbances to the power system and has placed increasing demands on power quality. In order to make full use of the power quality indicators in the national standards and to make a more comprehensive and integrated evaluation of power quality, this study proposes a power quality evaluation method based on graph convolutional network. A power quality assessment system with graded indicators is proposed according to the current national standards. The correlation between the various power quality assessment indicators is initially determined, and on this basis the indicator relationship diagram is determined, a graph neural network model is built and trained, and the error rate of the test set is 9.02%. A comparison and analysis with other assessment methods using actual measurement data of a power system proves that the proposed method is more effective in assessing power quality over a long time span. [ABSTRACT FROM AUTHOR]

The problem of Power Quality analysis is becoming crucial to ensuring the proper functioning of complex systems and big plants. In this regard, it is essential to rapidly detect anomalies in voltage and current signals to ensure a prompt response and maximize the system's availability with the minimum maintenance cost. In this paper, anomaly detection algorithms based on machine learning, such as One Class Support Vector Machine (OCSVM), Isolation Forest (IF), and Angle-Based Outlier Detection (ABOD), are used as a first tool for rapid and effective clustering of the measured voltage and current signals directly on-line on the sensing unit. If the proposed anomaly detection algorithm detects an anomaly, further investigations using suitable classification algorithms are required. The main advantage of the proposed solution is the ability to rapidly and efficiently detect different types of anomalies with low computational complexity, allowing the implementation of the algorithm directly on the sensor node used for signal acquisition. A suitable experimental platform has been established to evaluate the advantages of the proposed method. All the different models were tested using a consistent set of hyperparameters and an output dataset generated from the principal component analysis technique. The best results achieved included models reaching 100% recall and a 92% F1 score. [ABSTRACT FROM AUTHOR]

The ongoing replacement of synchronous machine generators (SMs) with converter-interface generators (CIGs) is raising the voltage unbalance of power systems, affecting power quality and grid stability. This paper focuses on a key power quality index for power systems, i.e., the voltage unbalance factor. The purpose of this work is twofold. First, it presents the generalization of a three-phase power flow algorithm developed by University of Padova, named PFPD_3P, to assess the voltage unbalance factors of power systems supplied by CIGs. In particular, it is demonstrated that CIGs can be modelled as three-phase PV/PQ constraints embedding their positive-, negative- and zero-sequence admittances. Then, the concept of three-phase contingency analysis is introduced. Indeed, for static security evaluation, the classical single-phase contingency analysis may no longer be sufficient, as it lacks power quality computations, e.g., voltage/current unbalance factors. Numerical simulations evaluating the unbalance factors due to different generation mix scenarios and contingencies are tested on the Italian extra-high-voltage/high-voltage (EHV/HV) grid. The choice of this network relies on its representativeness, as CIGs are the majority of new installations in the Italian generation mix. [ABSTRACT FROM AUTHOR]

In Korea, the demand for complete underground installation of power distribution equipment installed on roads and green areas is increasing. In addition, KEPCO is making efforts to build a more reliable system for the underground distribution system. To meet these needs, this paper proposes the S-substation. In the S-substation, an RMU, a large power transformer, and an LV-Board (including ATCB and MCCB) are installed within the underground structure. This paper proposes three models to apply the S-substation to the underground distribution system. Power flow analysis is conducted for each model by simulating a variety of loads and DERs, and the frequency fluctuations are also examined under different distribution system events. An economic analysis is also conducted to select the optimal model. The economic analysis focuses on VOLL and construction costs. Based on power flow and economic analysis, one model is selected, and the underground distribution system that the model is applied is presented. [ABSTRACT FROM AUTHOR]

Multi-functional photovoltaic (PV) inverters incorporate ancillary services to enhance power quality and mitigate stability issues in distribution networks. These next-generation PV inverters will achieve a higher utilization of the inverter's rated capacity, improving the cost-effectiveness of PV technology. However, the power required to perform ancillary services, such as load compensation capabilities, could exceed the inverter's capacity, risking the components' integrity. Therefore, multi-functional control algorithms must limit the power capacity according to the system's nominal currents. Despite this, most control proposals do not address this issue when load balancing capabilities are included for PV inverter control. This paper proposes a flexible control strategy for three-phase multi-functional PV inverters, considering load balancing functionalities while keeping the inverter currents within safe operating limits. The proposal introduces two control parameters whose variation results in different load compensation capabilities. These parameters can be adapted dynamically according to the inverter rated capacity not used for active power injection and the load compensation requirements. Additionally, a control algorithm is proposed to limit the inverter current according to the nominal values supported by the device. This algorithm also allows setting compensation objectives following a priority scheme in which the injection of the PV active power is prioritized over the load compensation functionalities. Reactive power compensation and load balancing functionalities are also considered at a lower level of hierarchical priority. The proposal was evaluated through experimental tests on a multi-functional PV inverter prototype under various operational conditions. The experimental results show an excellent control strategy performance, achieving the control objectives under unbalanced load conditions. [ABSTRACT FROM AUTHOR]

Summary: Problems like intermittent photovoltaic (PV) power, disconnected PV arrays, etc. are brought on by the extensive integration of PV generation. In this article, a single‐stage PV‐integrated grid‐tethered system is controlled using a reconfigurative multiple random features kernel mean p‐power (MRFKMP) control algorithm. The algorithm circumvents the dependence of kernel parameter in the classic random Fourier features mapping and lower the computing complexity in the traditional multiple kernel learning adaptive filter. MRFKMP algorithm with a linear filter structure can reduce both the computational and storage cost. This is the novel application of MRFKMP algorithm to extract fundamental component of nonlinear load currents in PV‐integrated grid‐tied system. Furthermore, to increase the reliability of the system, a reconfigurable control is developed, which adaptive regulates DC link voltage from PV mode (PVM) during PV hours to active power filtering mode (AFM) during PV nonavailability/PV disconnection. On a created laboratory testbed, the applied control's practical feasibility for numerous scenarios is evaluated. Comparison with existing control algorithms reveals that the MRFKMP controller outperforms the LMF based PV system by 79% less peak‐to‐peak load current ripple and 60% less than the best performing SRF control algorithm. The grid current THD is 2.60%, which is 30% low than that presented by SRF technique. [ABSTRACT FROM AUTHOR]

Active power filters (APFs) play a vital role in reducing the current harmonics and improving power quality. This work studies a shunt APF (SAPF) based on the threephase voltage source converter (VSC). This paper investigates the new robust control approach using error dynamics. Stable first-order error dynamics are considered when designing the control inputs. Three control inputs are obtained to control the currents at any phase by choosing and optimizing the appropriate parameters. This strategy is also simple to implement in practical applications because it is the same as the proportionalderivative controller design. In addition, the new control method can be utilized for any system with low dynamic information so that the destructive effects of lumped uncertainties in the output channels of the SAPF can be alleviated. The minimum voltage and current measurements are used to control the SAPF, and the grid current harmonics will be reduced by achieving the stabilization of tracking error dynamics. Some numerical simulations are performed by MATLAB software to confirm the proposed method. [ABSTRACT FROM AUTHOR]

This paper evaluates the performance of various PWM techniques for a 3-level inverter-based shunt active power filter by statistical parameters. It is well stated in the literature that the uses of power electronics-based devices create several power quality problems, such as poor power factor, harmonics in source current, poor voltage regulation, etc. Shunt active filters effectively alleviate these issues. A 3-level inverter, as a compensator depletes the harmonics in a single-phase grid-tied system. Level-shift, phase-shift, and hybrid PWM techniques generate switching pulses for 3-level inverter operation. These PWM techniques are compared for harmonic distortion at the source current, input power factor, and active filtering efficiency by statistical parameters such as mean squared error, root-mean-squared error, mean absolute deviation, mean absolute percentage error, standard deviation, variance, mean absolute error, and mean relative error. The above statistical parameters have been used to determine the optimum PWM technique for shunt active power filter operation. It is revealed from the results that for the PS PWM technique, the MSE is found to be less, i.e., 0.049441, and also has a low THD, i.e., 1.22% in source current. The behaviour of these PWM schemes is analysed through MATLAB/Simulink 2021b software. This paper contributes extensive information on PWM schemes for 3-level inverter-based compensator. It will help to comprehend various aspects of the power quality of a single-phase distribution system. [ABSTRACT FROM AUTHOR]

The impact of the quality of electricity on the pantograph is an important parameter for the supply of locomotives in railway companies (RCs). The subject of this research is the analysis of the quality of electricity on the pantograph of the 441-series locomotivelocated at distances of 1 km or 35 km from the power station in the electric traction system of Serbian Railways. The analysis included the simulation of the system in the MATLAB-Simulink software package (R2016a), which resulted in data that were often difficult to measure due to the complexity of the electric traction system. The obtained values indicate that the total harmonic voltage distortion on the pantograph of the 441 locomotive is 16.34% for 1 km and 51.06% for 35 km, while the EN 50160 standard prescribes a maximum of 8%. The total harmonic distortion current in the electric traction substation and through the locomotive pantograph is 33.42% (for 1 km) and 32.53% (for 35 km), showing anomalies in the supply of locomotives in RCs. [ABSTRACT FROM AUTHOR]

The increasing use of nonlinear loads in power systems introduces voltage and current components at non-fundamental frequencies, leading to harmonic distortion, which negatively impacts electrical and electronic devices. A common mitigation strategy involves identifying harmonic sources and installing filters nearby. However, due to the high cost of power quality (PQ) meters, comprehensive harmonic level monitoring across the entire power system is impractical. To address this, various methodologies for Harmonic State Estimation (HSE) have been developed, which estimate distortion levels on unmonitored system buses using data from a minimal set of monitored ones. Many HSE techniques rely on optimization algorithms with numerous tuning parameters, complicating their application. This paper proposes a novel methodology for fundamental frequency power flow and harmonic state estimation using the Jaya algorithm, which is characterized by fewer tuning parameters for easier adjustment. It also introduces a strategy to determine the minimal number of buses that need monitoring to achieve system observability. The methodology is validated on the IEEE-14 and IEEE-30 bus systems, demonstrating its effectiveness. The results of the proposed methodology are compared with those obtained using Evolutionary Strategies (ESs), highlighting its enhanced accuracy and computational efficiency. [ABSTRACT FROM AUTHOR]

The noticeable dynamic development of electromobility poses new challenges for the energy industry and users of electric vehicles. One of these challenges is coping with the change in the way we refuel. In the case of electric vehicles, the batteries can also be charged via home electrical installations. The presence of a new, non-linear load with significant power may affect the quality parameters of electricity in this installation and therefore indirectly affect the operation of other loads. In order to investigate the possible impact of the electric vehicle charging process on these parameters, a number of measurements were carried out. This paper presents the results of observing voltage distortions in the installation as a result of the harmonics of the current supplying the AC/DC converter in the vehicle. The test results confirm the compliance of the voltage with the requirements of the standards; however, the large share of current harmonics requires the analysis of the anti-shock protections existing in the installation to ensure that they are effective when currents at higher frequencies flow. The research results may be a guide for designers and users of home electrical installations. [ABSTRACT FROM AUTHOR]

Considering the widespread presence of switching devices on the power grid (including renewable energy system inverters), network distortion is more prominent. To maximize network efficiency, our goal is to minimize these distortions. Measuring the voltage and current total harmonic distortion (THD) using power meters and other specific equipment, and assessing power factor and peak currents, represents a crucial step in creating an efficient and stable smart grid. In this paper, we propose a power meter capable for measuring both standard electrical parameters and power quality parameters such as the voltage and current total harmonic distortion factors. The resulting device is compact and DIN-rail-mountable, occupying only three modules in an electrical cabinet. It integrates both wired and wireless communication interfaces and multiple communication protocols, such as Modbus RTU/TCP and MQTT. A microSD card can be used to store the device configuration parameters and to record the measured values in case of network fault events, the device's continuous operation being ensured by the integrated backup battery in this situations. The device was calibrated and tested against three industrial power meters: Siemens SENTRON PAC4200, Janitza UMG-96RM, and Phoenix Contact EEM-MA400, obtaining an overall average measurement error of only 1.22%. [ABSTRACT FROM AUTHOR]

This paper presents the design of active harmonic current compensator (AHCC) to mitigate the current harmonics generated by supply side for an induction furnace application. Induction furnaces have nonlinear and time-varying properties, resulting in harmonics and voltage/current imbalances. AHCC are high-speed compensators that enhance the performance of induction furnaces and solve power quality issues. The proposed system is designed with modified higher order sliding control (MHOSC) algorithm and extended form of reactive power theory to generate a three-phase reference compensating current. The control method examines the sliding surface parameter uncertainties in order to obtain a controlled direct current (DC) link current when using nonlinear converters. The proposed work compares the performance of proportional integral (PI) tuned sliding mode controllers with emotional tuned intelligent controllers (ETIC). The compensated current reference signal is used to provide switching pulses for AHCC. A major advantage of MHOSC is its ability to endure external disruptions and unpredicted parameter changes, which improves reference current tracking without introducing undesirable oscillations (chattering). Implementation of the proposed control algorithm is validated in MATLAB / Simulink demonstrating that the designed AHCC compensates the harmonic current to an acceptable level (total harmonic distortion of source current is 1.54%) satisfying IEEE 519-2014 standard. [ABSTRACT FROM AUTHOR]

Off-grid wind energy systems play a pivotal role in providing clean and sustainable power to remote areas. However, the intermittent nature of wind and the absence of grid connectivity pose significant challenges to maintaining consistent power quality. The wind energy conversion system plays a central role in tapping renewable energy from wind sources. Operational parameters such as rotor and stator currents, output voltages of rectifiers and converters, and grid phase voltage variations are crucial for stable power generation and grid integration. Additionally, optimizing power conversion output through voltage gain analysis in boost converters is essential. Moreover, ensuring electricity quality via total harmonic distortion reduction in inverters is vital for grid compatibility. Goal. Enhancing the power quality of grid-integrated wind energy conversion systems. Methods. The proposed topology is implemented in MATLAB/Simulink with optimized control strategies for enhancing power quality in off-grid wind energy systems. Results. Control strategies with a grid-connected wind energy conversion system yields substantial improvements in power quality. This includes effectively mitigating voltage fluctuations and harmonics, resulting in smoother operation and reduced disturbances on the grid. Practical value. The proposed topology has proven to be extremely useful for off grid-integrated wind system. References 18, table 1, figures 11. [ABSTRACT FROM AUTHOR]

This paper deals with Distributed Generation (DG) system requiring power quality features such as current harmonics, reactive power compensation, and power factor improvement in grid tied operation. The motivation is to combine DG system with the capabilities of shunt active filter to perform real power injection, current harmonics mitigation and power factor improvement. The control algorithm employed in this setup utilizes a reference current generator based on p-q theory together with a pulse width modulation controller for switching pulse generation. The control strategy utilizes PI controller with Genetic Algorithm (GA) and Particle Swarm Optimization (PSO) for finding optimal PI controller parameters. The effectiveness of the proposed method is verified using MATLAB/Simulink and experimental model developed for 3kWp inverter. The PI-PSO controller injects 0.588kW active power into the grid results in sharing 54% of load power demand and the current harmonics is reduced from 23.70% to 1.63%. The obtained results demonstrate that the grid tied inverter maintains harmonic standards in accordance with the IEEE-519 standard while injecting maximum possible active power to the line. [ABSTRACT FROM AUTHOR]

A fourth-order generalized integrator (GI)-based frequency locked loop (AFOGI-FLL) controller is proposed to provide switching pulses for a three-phase IGBT-based voltage source converter. Accurate frequency synchronization, lower- and higher-order harmonic elimination, power quality refinement, and reactive power compensation are the features of the presented controller. As a renewable energy solution to meet energy demands, grid-interfaced photovoltaic systems are described in this paper. To stabilize DC link voltage, a novel ANFIS-based hybrid intelligent controller is proposed. In addition, a comparative analysis has been performed between the proposed controller and the third-order generalized integrator (TOGI). The comparative analysis results show that fourth-order generalized integrator has higher DC offset elimination capability and better dynamic performance as well and THD is less compared with the TOGI controllers. The THD of the proposed controller is 1.10% which is less than the IEEE standard. The proposed controller robustness is validated by an experimental prototype setup and test results exhibit the performance under non-linear loading. Additionally, the feasibility of the proposed control scheme is demonstrated by using MATLAB/SIMULINK software. The system is well executed under irradiance variations, load fluctuations, and frequency variations as well. The laboratory prototype is used to demonstrate the proposed system's simulated behavior and experimental test results. [ABSTRACT FROM AUTHOR]

This paper presents a novel architecture to enhance the performance of grid‐connected photovoltaic (PV) systems through the introduction of several key novelties. Firstly, a packed U‐cell seven‐level (PUC7)‐based single‐phase solar active filter is implemented, offering a comprehensive solution for harmonics mitigation, reactive power compensation, and efficient power extraction from the PV source, while facilitating the injection of real power into the grid. Secondly, the p‐q power injection algorithm is modified to accommodate the extraction of solar power from the PV generator to the grid, simultaneously addressing the need for harmonic current injection to improve power quality. This modification ensures dynamic performance by extracting reference current with harmonic content and solar power information, thereby enhancing the system's overall efficiency. Lastly, the proposed architecture undergoes real outdoor testing, validating its performance in various key aspects including maximum power tracking, reduction of total harmonic distortion in comparison with previous work, operation at unity power factor, and testing the effective operation of the multifunction feature. These contributions collectively demonstrate the effectiveness of the proposed system in enhancing power injection quality and reactive power compensation under real outdoor conditions of PV systems connected to the grid. [ABSTRACT FROM AUTHOR]

The presence of non-linear, time-variant loads in power networks introduces harmonics and other power quality issues in voltage and current waveforms. With the growing prevalence of power electronics, managing harmonic distortion has become a significant challenge in modern power distribution systems. This study aims to assess and analyze power quality at various locations within an academic institution (Sultan Qaboos University). The study encompasses the outputs of PV converters, uninterruptible power supplies (UPS), chillers with variable-speed motors, 11 kV/415 V transformers at both the College of Engineering and the Center of Information Systems, as well as two main substations supplying power to the university (33 kV/11 kV). Data collected—such as harmonic content in current and voltage waveforms and Total Harmonic Distortion (THD)—were meticulously analyzed to identify the factors affecting waveform quality. Measurements were conducted using advanced power quality instruments (Fluke 435-II), and the data were analyzed using MATLAB software. The study reveals that most results adhered to both the Oman grid code and international standards. The findings and methodology presented in this paper provide a critical benchmark for guiding standards compliance as Sultan Qaboos University, and other academic institution, undertakes the modernization of aging equipment and the expansion of new high-tech facilities. [ABSTRACT FROM AUTHOR]

With the connection of distributed power generation and a large number of nonlinear loads to the power grid, the problem of power quality disturbance is becoming more and more prominent, and the loss of key equipment in the distribution network is seriously affected. At present, the transformer loss in the condition of multiple power quality disturbances is difficult to be accurately measured, and the loss influence degree of each transformer is difficult to be quantified by various power quality indicators. Therefore, according to the three typical power quality disturbance mechanisms of voltage deviation, three-phase unbalance and harmonic, a experimental platform which could simulate the actual operating conditions of the transformer and generate multiple power quality disturbance conditions was designed. In addition, the grey correlation analysis method was used to process the experimental data, and the correlation degree between each power quality index and transformer loss was obtained. The results show that the transformer loss will be affected by three power quality indicators, which will affect the energy efficiency of the transformer. The additional loss of the distribution network transformer is most significantly affected by the coupling between the three-phase unbalanced disturbance and other disturbances, while the additional loss is less affected by the coupling between the voltage deviation disturbance and other disturbances. This conclusion can be considered a valuable reference for the analysis of energy efficiency in distribution networks and the control of power quality. [ABSTRACT FROM AUTHOR]

Hybrid Renewable Energy Systems (HRES) have recently been proposed as a way to improve dependability and reduce losses in grid-connected load systems. This research study suggests a novel hybrid optimization technique that regulates UPQC in order to address the Power Quality (PQ) problems in the HRES system. The load system serves as the primary link between the battery energy storage systems (BESS), wind turbine (WT), and solar photovoltaic (PV) components of the HRES system. The major objective of the study is to reduce PQ issues and make up for the load requirement inside the HRES system. The addition of an Optimized Fractional Order Proportional Integral Derivative (O-FOPID) controller improves the efficiency of the UPQC. The Crow-Tunicate Swarm Optimization Algorithm (CT-SOA), an enhanced variant of the traditional Tunicate Swarm Optimization (TSA) and Crow Search Optimization (CSO), is used to optimize the control parameters of the FOPID controller. Utilizing the MATLAB/Simulink platform, the proposed method is put into practice, and the system's performance is assessed for sag, swell, and Total Harmonic Distortion (THD). The THD values for the PI, FOPID, and CSA techniques, respectively, are 5.9038%, 4.9592%, and 3.7027%, under the sag condition. This validates the superiority of the proposed approach over existing approaches. [ABSTRACT FROM AUTHOR]

Voltage fluctuations are one of the most common problems in low-voltage networks. Very often, these disturbances cause damage to or the incorrect operation of electrical devices. Unfortunately, at present, the monitoring of these disturbances relies on short-term and long-term flicker indicators, which only assess the severity of one of the effects of voltage fluctuations. Another measure of voltage fluctuations that has greater diagnostic potential is voltage fluctuation indices, i.e., the amplitude and rate of voltage fluctuations. One advantage of these indices that has been highlighted in recent years is their potential ability to recreate voltage fluctuations using these indices. This article presents research results that allow for the verification of the potential of voltage fluctuation indices as a method for recreating voltage fluctuations. For verification purposes, various cases of voltage variation recorded in a modern low-voltage network are used. The analysis of the possibility of recreating voltage fluctuations from voltage fluctuation indices presented in this article, in association with previously carried out numerical simulation studies and experimental laboratory studies, constitutes a complementary whole and indicates further directions in voltage fluctuation research in terms of the electromagnetic compatibility of low-frequency conducted disturbances. [ABSTRACT FROM AUTHOR]

Electric vehicle technology is transitioning from mobility based on fossil fuel combustion to one based on vehicle electrification, in which the primary energy is increasingly renewable, and the generation of pollutants and CO2 emissions is being reduced. This paper provides a tour of the key aspects of these systems, reviewing their most important historical, legislative, and grid impact topics. For this purpose, a literature review of publications up to 2022 is conducted. The last decade is the subject of a deeper analysis, shedding light on the essential characteristics of this technology and fundamentally focusing on its integration into electrical distribution networks. This work is carried out based on a review of a selection of articles written by authors worldwide who have researched these topics. We ordered and analyzed the temporal evolution of the defined categories, obtaining their research line direction. A meta-analysis of grid impact was also carried out, prompting clear conclusions about the state of the art and potential future works. [ABSTRACT FROM AUTHOR]

Constructing agricultural microbial gasification plants near livestock farms is essential for technical, economic, and environmental reasons. Utilising substrates from these farms allows for producing electricity, heat, and environmentally friendly manure. However, biogas plants often face technical challenges. This study evaluates the power quality of an agricultural biogas plant on a dairy farm. It was found that the plant was connected via a cable with an insufficient conductor cross-section, leading to significant voltage overshoots exceeding 14.6%, which prevented the activation of the second generator. Both generators could operate after replacing the feed-in cable, but considerable fluctuations in the feed-in voltage persisted. Further measurements indicated the need for changes in the digester design. Specifically, replacing the current two mixers with more lower-powered mixers operating alternately was proposed. Sharing these solutions more broadly can help prevent similar issues in future microbial gas plant constructions and optimise electricity production. [ABSTRACT FROM AUTHOR]

AbstractThe Chernobyl accident taught us an important lesson regarding the significance of the emergency diesel generator (EDG), which is crucial for supplying a nuclear facility with emergency alternating-current power. A worst-case scenario would occur if the EDG failed to start functioning. In response to this problem, this research addresses the issue and suggests an optimal design for another alternative electrical source using solar energy. Until now, employing this technology presented a challenge as a solar energy system generates electrical harmonics that are transmitted from the photovoltaic (PV) grid to the electrical network. These harmonics can negatively impact the performance and operation of nuclear facilities.Consequently, this study proposes a comprehensive investigation that tackles this issue by implementing a LCL filter to mitigate the harmonics in the PV network. This paper not only provides an alternative solution in the event of a diesel generator breakdown, but also studies the effect of this solution on the station’s performance and how to improve it. A mathematical model based on the MATLAB program is developed to simulate the application of the LCL filter strategy. The proposed technique is tested through simulation with an actual case, demonstrating its reliability and high-quality outcomes. [ABSTRACT FROM AUTHOR]

Currently, the solar photovoltaic (PV) systems are becoming more and more important in order to meet the world's increasing demand for electricity. In this study, a unique Hybrid Group Search Integrated Rider (HGSR)-MPPT control technique is developed to track the maximum solar energy from the PV panels in order to meet the grid systems' need for electricity. Then, the output voltage of the PV is boosted using the cutting-edge Cuk Step-Up converter, which has a higher voltage gain efficiency and lower stress voltage between the switches. Consequently, the Self-Adaptive Rao Control (SARC) technique is implemented to produce the pulses required to actuate the converter's switching components. More specifically, the improved switched capacitor five-level inverter circuit is modelled in this study to improve the grid unit's power quality with low leakage current, switching stress, and minimal component consumption. In order to improve the performance of the MLI's switching operating modes, the unique Deep Reinforced Q-Learning Control (DRQLC) technique is implemented. The output voltage, current, power, THD, and voltage gain efficiency of the proposed controlling mechanisms' simulation results are evaluated and analyzed. • To track the maximum solar energy from the PV panels. • The improved switched capacitor five-level inverter circuit Proposed. • Deep Reinforced Q-Learning Control (DRQLC) technique is implemented. • Cuk Step-Up converter is being used to boost the output voltage of PV. • Five level inverter and DQRLC control technique produce good grid performance in terms of 99% efficiency and 1.12% of THD. [ABSTRACT FROM AUTHOR]

The large-scale integration of renewable energy sources and power electronic devices has led to increasingly dispersed and networked characteristics of power quality disturbances in distribution systems. Traditional control devices, limited by their fixed-point control, no longer meet the development needs of modern distribution systems. Considering the distribution and structural characteristics of the current new-type sources and loads, a multifunctional inverter power quality coordinated control strategy based on comprehensive evaluation is proposed. This strategy aims to achieve power quality coordinated control by utilizing optimal compensation capacity while the grid-connected inverter provides active power output. Firstly, the traditional ipiq power quality detection method is analyzed and improved to enable detection of harmonics, reactive power, and three-phase imbalance currents in single-phase systems or threephase four-wire systems. Secondly, in the power quality assessment, a balanced algorithm is employed to obtain the comprehensive evaluation index of power quality, thereby improving the deficiencies of single-weight evaluation. Next, to ensure the grid-connected inverter achieves optimal power quality coordinated control with minimal compensation capacity, an optimization compensation function is established between compensation capacity and comprehensive power quality index. This function is optimized using non-dominated sorting genetic algorithm to enhance equipment utilization and system economy. Finally, the feasibility and effectiveness of the proposed method are validated through simulations, demonstrating the achievement of optimal capacity configuration for power quality coordinated control while ensuring active power output by the grid-connected inverter. [ABSTRACT FROM AUTHOR]

The primary objective of this paper focuses on developing a control approach to improve the operational performance of a three-level neutral point clamped (3LNPC) shunt active power filter (SAPF) within a grid-tied PV system configuration. Indeed, this developed control approach, based on the used 3LNPC-SAPF topology, aims to ensure the seamless integration of a photovoltaic system into the three-phase four-wire grid while effectively mitigating grid harmonics, grid current unbalance, ensuring grid unit power factor by compensating the load reactive power, and allowing power sharing with the grid in case of an excess of generated power from the PV system, leading to overall high power quality at the grid side. This developed approach is based initially on the application of the four-wire instantaneous p-q theory for the identification of the reference currents that have to be injected by the 3LNPC-SAPF in the grid point of common coupling (PCC). Whereas, the 3LNPC is controlled based on using the finite control set model predictive control (FCS-MPC), which can be accomplished by determining the convenient set of switch states leading to the voltage vector, which is the most suitable to ensure the minimization of the selected cost function. Furthermore, the used topology requires a constant DC-link voltage and balanced split-capacitor voltages at the input side of the 3LNPN. Hence, the cost function is adjusted by the addition of another term with a selected weighting factor related to these voltages to ensure their precise control following the required reference values. However, due to the random changes in solar irradiance and, furthermore, to ensure efficient operation of the proposed topology, the PV system is connected to the 3LNPN-SAPF via a DC/DC boost converter to ensure the stability of the 3LNPN input voltage within the reference value, which is achieved in this paper based on the use of the maximum power point tracking (MPPT) technique. For the validation of the proposed control technique and the functionality of the used topology, a set of simulations has been presented and investigated in this paper following different irradiance profile scenarios such as a constant irradiance profile and a variables irradiance profile where the main aim is to prove the effectiveness and flexibility of the proposed approach under variable irradiance conditions. The obtained results based on the simulations carried out in this study demonstrate that the proposed control approach with the used topology under different loads such as linear, non-linear, and unbalanced can effectively reduce the harmonics, eliminating the unbalance in the currents and compensating for the reactive component contained in the grid side. The obtained results prove also that the proposed control ensures a consistent flow of power based on the sharing principle between the grid and the PV system as well as enabling the efficient satisfaction of the load demand. It can be said that the proposal presented in this paper has been proven to have many dominant features such as the ability to accurately estimate the power sharing between the grid and the PV system for ensuring the harmonics elimination, the reactive power compensation, and the elimination of the neutral current based on the zero-sequence component compensation, even under variable irradiance conditions. This feature makes the used topology and the developed control a valuable tool for power quality improvement and grid stability enhancement with low cost and under clean energy. [ABSTRACT FROM AUTHOR]

To enhance the power supply reliability of the microgrid cluster consisting of AC/DC hybrid microgrids, this paper proposes an innovative structure that enables backup power to be accessed quickly in the event of power source failure. The structure leverages the quick response characteristics of thyristor switches, effectively reducing the power outage time. The corresponding control strategy is introduced in detail in this paper. Furthermore, taking practical considerations into account, two types of AC/DC hybrid microgrid structures are designed for grid-connected and islanded states. These microgrids exhibit strong distributed energy consumption capabilities, simple control strategies, and high power quality. Additionally, the aforementioned structures are constructed within the MATLAB/Simulink R2023a simulation software. Their feasibility is verified, and comparisons with the existing studies are conducted using specific examples. Finally, the cost and efficiency of the application of this study are discussed. Both the above results and analysis indicate that the structures proposed in this paper can reduce costs, improve efficiency, and enhance power supply stability. [ABSTRACT FROM AUTHOR]

Metro trains have non-linear load characteristics, which means that the power sent to them gets distorted. Problems are caused by changes in power, swells, harmonics, and other disturbances. In this research, an artificial intelligence-driven control method was used on a unified power quality conditioner (UPQC) to help reduce power quality problems and improve power quality. Three advanced control methods are built and compared using MATLAB Simulink. Some of these methods are the ANN Controller, the NARMA-L2 Controller, and the PI Controller, improved using the Adaptive Lizard Algorithm. The controls' usefulness is judged by how well they lower the total harmonic distortion (THD) in the source current. The results show that all three AI-based controls work much better than the system that was not paid for. The ANN Controller works the best, followed by the NARMA-L2 Controller, and the PI Controller improved with the Adaptive Lizard Algorithm. These AI-driven control methods can enhance power quality and ensure that metro rail systems run smoothly and efficiently, as shown by how well they work. Modern transportation networks need more advanced ways to handle power quality, and this research helps make those solutions come together. [ABSTRACT FROM AUTHOR]

This work presents a variable step Champernowne Adaptive Filter (VS-CAF) based control architecture for a grid-integrated solar photovoltaic system. The control structure is implemented to successfully synchronize the two-stage solar photovoltaic at the point of common coupling where the source and domestic loads are connected. The control architecture ensures solar power injection and improvised power quality at the unity power factor. Moreover, the control structure provides only the balanced positive sequence fundamental sinusoidal source currents at solar irradiation alteration and load disturbances. The VS-CAF is exploited to estimate the peak of the fundamental component out of the harmonics-rich domestic load currents. To examine the efficacy of the suggested control technique, a 40 kW solar photovoltaic is simulated using MATLAB/Simulink. The performance assessment of the grid-tied solar generation system is carried out at solar irradiation alteration, zero solar irradiation, and detachment of one phase of the three-phase load. Various simulation results are carried out to verify the successful integration of solar photovoltaics into the three-phase grid following the IEEE-519 standard and satisfactory performance during various working conditions. Moreover, the simulation results are also verified with real-time results taken from the Opal-RT simulator. [ABSTRACT FROM AUTHOR]

Contingency analysis has been vastly explored within the context of power systems operation and security assessment. However, the impact of power quality indices into the contingency ranking and selection has not been well investigated in the literature. In order to fulfil this gap, a novel approach is proposed in this paper considering the effects of transmission lines outages in the voltage magnitudes and harmonic proliferation in power systems. The compensation theorem is applied to obtain the approximate effect of small changes in the elements of an electric network based on sensitivity analysis with the purpose of determining estimated harmonic voltages and currents in a lower computational time when compared with the traditional application of the iterative Newton–Raphson load flow methodology. Computational simulations are carried out using the IEEE 30 bus test system modified by the inclusion of non linear loads modelled as harmonic current injections. A comparative analysis is also presented considering the contingency selection using the proposed method, load flow algorithms and different ranking factors considering the impact of single contingencies into the power system voltages and total harmonic distortion variations. [ABSTRACT FROM AUTHOR]

This study introduces an integrated power quality (PQ) conditioner, referred to as UPQC, that is linked with photovoltaic (PV) and battery energy systems (BSS) in order to address and solve PQ issues. It is proposed to employ the Levenberg–Marquardt (LM) backpropagation (LMBP) trained artificial neural network control (ANNC) technique for generating reference signal for converters in UPQC. This approach eliminates the need for traditional abc to dq0 to αβ conversions. Additionally, the hybrid algorithm (FFHSA) in combination of harmony search algorithm (HSA), and firefly algorithm (FFA) is also implemented for the optimal selection of adaptive neuro-fuzzy interface system (ANFIS) parameters to maintain direct current link capacitor voltage (DLCV) constant. The prime goal of the developed hybrid ANNC-FFHSA is to stabilize the DLCV with low settling time during load and solar irradiation (G), Temperature (T) changes, minimization of distortions in the source current signal to diminish total harmonic distortion (THD) in turn boosting the power factor (PF), suppression of fluctuations like disturbances, swell, sag and unbalances in the supply voltage. The suggested method is validated by four test cases with several combinations of variable irradiation (G), temperature and loads. On the other hand, to reveal the superiority of the developed method, the comparison is carried out with the genetic algorithm (GA) and Ant colony algorithm (ACA) along with instantaneous power (p–q) and Synchronous reference frame (SRF) conventional methods. The proposed approach significantly diminishes the total harmonic distortion to values of 3.61%, 3.48%, 3.48%, and 4.51%, which are notably lower compared to the values reported in the existing literature and also improves the power factor to almost unity. The design and implementation of this method were carried out using MATLAB/Simulink software. [ABSTRACT FROM AUTHOR]

The integration of electric vehicles (EVs) into the power grid could pose challenges to power quality (PQ) depending on quantity of EVs and when they are connected. To mitigate these impacts without using drastic measures, such as disconnecting EVs, this study investigates centralized control strategies within parking facilities that prioritize EV charging based on individual State of Charge (SoC) levels. The study utilizes the IEEE 34 Bus system and conducts 3888 simulations for different scenarios to assess the impact of the quantity and placement of EVs in parking lots. The study applies the Monte Carlo method to compare the performance of different proposed controls: (i) limiting the charging current to a fixed level and (ii) varying the current based on the voltage droop step. Furthermore, Power Hardware‐in‐the‐Loop (PHIL) simulations were carried out to validate the hierarchical control using the droop step control, demonstrating the best average performance in the previous scenarios. The findings indicated that the control responded within the expected timeframe and successfully addressed voltage sag issues, maintaining PQ in the distribution system in most cases, with its performance being influenced by the placement of parking lots in the network. Additionally, it was confirmed through quartiles that the classification based on SoC leads to a more balanced charging time for different SoC levels. [ABSTRACT FROM AUTHOR]

In this manuscript, a new control approach is counselled for DSTATCOM to resolve power quality (PQ) related issues. The Non-dual Adaptive Controller (NDAC) is employed with DSTATCOM to enhance the performance in terms of stability. The DSTATCOM is the constituent of voltage source inverter shunt DC-capacitor. A hysteresis block is employed for switching pulse triggering. The counselled scheme is a new method of shunt compensation and offers superior performance, for the lower frequency band in comparision with traditional strategies. Now-a-days we are dealing with huge nonlinear loads which draws non sinusoidal currents and also they generate large amount of harmonics. There are various advantages of using this new modified adaptive controllers over the tradition controllers. We are going to compare the performance of this new counselled controllers performance with the existing one in this literature. This new controller is initially simulated over MATLAB 2016 and then the efficacy of the counselled control approach (NDAC) is investigated using Laboratory prototype. Hardware setup is then authenticated through prototype with the help of dSPACE 1104. The execution reflects wide variation in the performances of both the controllers and also shows the supremacy of Non-dual adaptive controllers in terms of various aspects like harmonic current reduction, reduction in Total harmonic distortions during load dynamics. [ABSTRACT FROM AUTHOR]

Power Quality, Equipment and Personnel safety of any distributed generation (DG) system connected to utility Grid merely depends on accurate detection of Islanding and non-islanding Power quality disturbances. The main objective of the proposed research is to detect islanding events with very narrow non-detection zone (NDZ) and classification of power quality disturbances with higher accuracy using signal processing and intelligent method together. A noise robust down sampling empirical mode decomposition (DEMD) is used to extract signature of islanding and power quality (PQ) disturbance features from the collected voltage signals and multilayer perceptron neural network (MLNN) is proposed to classify islanding and non-islanding (PQ) events. The performance of the proposed (DEMD-MLNN) technique is verified with IEEE-9 bus distributed generation system dominated by solar &wind energy penetration. The simulation work is carried out in MATLAB/Simulink platform. The efficacy of the proposed DEMD-MLNN is verified by large number of numerical experimentations with and without noise and comparing with existing competitive well-known techniques. [ABSTRACT FROM AUTHOR]

Harmonic state estimation (HSE) is an useful technique for determining harmonic voltages and currents in electric power systems based on synchronized measurements and network impedances parameters. However, measurements and parameters data can be corrupted by gross errors yielding unsatisfactory estimation results. Despite recent methods have been proposed for HSE in power systems, there are few works considering both harmonic state variables and parameters estimation. In order to solve this problem, this paper presents a generalized harmonic state estimation considering uncertain network parameters and synchronized measurements. In the proposed approach, harmonic voltage and current phasors are obtained by measurement units allocated along the system. Network parameters, such as line and load impedances, are treated as inequality constraints in an optimization problem formulation considering both system state variables and parameters to be determined by the proposed HSE. The main contribution of this research paper is the use of a deterministic approach for estimating both harmonic state variables and parameters with reduced estimation errors when compared with the traditional weighted least squares (WLS) technique. Computational simulations are carried out using the IEEE test systems and results are also validated using RSCAD (Real-Time Simulation Software Package) software. [ABSTRACT FROM AUTHOR]

This research article details the design and implementation of a nonlinear adaptive filtering (NAF) technique using an exponential functional link network (EFLN) for a shunt hybrid active power filter (SHAPF) control to solve the current-associated power quality issues on the utility side at the distribution level of electrical power systems. Separation of the fundamental component from the harmonics, achieving unity power factor operation, reducing the reactive power drawn from the source, balancing the currents during transients, and reduction of total harmonic distortion (THD) of the source current are the issues considered to resolve. The proposed technique solves these issues by generating the sinusoidal reference current and separating the fundamental current from the harmonics. When compared to conventional and existing adaptive filtering techniques such as least mean square (LMS), least mean fourth (LMF), and variable step size LMS (VSS-LMS), the proposed EFLN-NAF method excels in terms of speedy convergence, adaptability in noise-specific environments and reduced steady-state coefficient error. MATLAB/Simulink software is utilized to perform the simulations to examine the suggested strategy for the chosen SHAPF topology both in static and dynamic scenarios. For a 15 kW and 3kVAr requirement of the nonlinear load, simulation results proved that the designed PPF for 2kVAr is able to share the reactive power with the APF, thereby reducing its rating and cost. The proposed method of filtering has been proven to be fast converging with 0.049 s, and the THD in steady state is brought to 1.32 % in steady-state and to 3.77 % during transient conditions, which are under standard limits. A hardware prototype of the experimental setup is constructed at the laboratory scale with OPAL-RT (OP4510) as the controller. With an active and reactive power demand of 1.1 kW and 210VAr, the designed PPF supplies 110 VAr, whereas the rest is supplied by the APF. The practical THD in source current is observed to be 2.081 %, which meets the standards. The results from both simulations and experiments are validated, and the efficacy of the proposed technique in mitigating the aforementioned power quality issues is proved. [Display omitted] • A passive power filter design to share the reactive power requirement in addition to mitigating the predominant harmonics of the 5th and 7th order. • A robust nonlinear adaptive filter implementation based on exponential functional link network (EFLN-NAF) algorithm to the shunt hybrid active power filter (SHAPF) control for reference current generation and fundamental component separation from harmonics. • Solution for current-associated power quality issues such as reducing the reactive power burden, achieving unity power factor operation, and mitigating the harmonics, thereby reducing the source current THD value. • Simulation of the proposed technique for the control of shunt hybrid active power filter and evaluation of the outcomes for resolving the power quality issues in both steady-state and dynamic conditions. • Development of a hardware prototype at a laboratory scale using OPAL-RT (OP4510) real-time simulator as a controller for the proposed technique for the control of SHAPF and evaluation of the outcomes. [ABSTRACT FROM AUTHOR]

Copyright of Power Generation Technology is the property of Power Generation Technology Editorial Office and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

The burgeoning energy demands induced by modern civilization necessitate the procurement of additional electrical energy reserves to effectively address this escalating challenge. However, the installation of new power generation units necessitates building/upgrade of accompanying transmission infrastructure, a task fraught with complexities. To augment the loading capacity of existing transmission lines, power engineers have devised efficient solutions, one of which involves the integration of novel devices. This paper delves into the management of reactive power within vulnerable transmission networks, focusing particularly on the pivotal role of Flexible AC Transmission System (FACTS) devices. Among the diverse array of FACTS technologies engineered to fortify grid resilience, the Static Synchronous Compensator (STATCOM) which emerges as a transformative asset. The paper explores the integration of STATCOM within the 132 kV transmission network of the Diyala city ring power system to enhance its stability and operational efficiency. Simulations of the Diyala power network and load flow analysis were conducted using MATLAB/Simulink environment. The results unveiled a notable enhancement in power quality upon the integration of STATCOM, as compared to the base scenario devoid of such augmentation. These findings bear significant implications, offering valuable insights for the Iraqi grid operator and other nations grappling with analogous challenges pertaining to frail power networks. Incorporating such advanced devices into national electrical systems could potentially mitigate operational inefficiencies, defer infrastructure investment and bolster overall grid resilience. [ABSTRACT FROM AUTHOR]

The paper presents a normalized, varying step size-based least mean square-based control for a standalone microgrid and Ant Lion optimization-based maximum power point tracking. This modified version of the incremental conductance algorithm addresses issues like slow dynamic response, fixed step size issues, and steady state oscillations. Comparative analysis with well-known techniques shows that Ant Lion optimizes the tracking of maximum power points more accurately, with fewer oscillations and increased efficiency. Power management and power quality are maintained through proposed adaptive voltage source converter control. The proposed voltage control shows better performance under various dynamic and steady conditions. [ABSTRACT FROM AUTHOR]

Over the past two decades, Renewable Energy Sources (RESs) have gained global popularity. Control issues are becoming more difficult as the system inertia decreases due to the absence of typical synchronous generators. Innovative methods like fault current limiters, energy storage devices, and alternative control systems are utilized to deal with these difficulties. This study provides a summary of the challenges associated with incorporating high-level RESs into the existing grid. The increased penetration of the RESs has a negative impact on the system oscillations and harmonics, generating the need for power quality improvement techniques, such as adaptive control, adding energy systems, power stream assessment, or weight stream examination. This paper presents a framework of the power stream issue, its arrangement as well as different game plan methods. The power stream model of a power structure can be built using the significant association, weight, and age data. [ABSTRACT FROM AUTHOR]