Search

This paper presents experimental studies to investigate the compressive and shear behaviors of cold-formed thin-walled steel-foam concrete composite walls. Three compressive walls and three shear walls were tested. The failure mode and load-displacement curve of the specimen were obtained from the compressive experiment. The compressive wall infilled with foam concrete mainly experienced distortion buckling of the end stud and local crushing failure of the concrete. The stud openings had a limited effect on the compressive bearing capacity of the composite wall. The failure mode and load-deformation curve were obtained in shear tests. The ductility index, shear stiffness, yield load, peak load, energy dissipation, and stiffness degradation were analyzed. The shear composite wall filled with foam concrete mainly occurred concrete crushing failure, local or distortional buckling failure of the end stud, and cracking failure of the calcium silicate board. The shear stiffness, shear capacity, ductility, and energy dissipation of the composite wall could be significantly improved after filling with foam concrete. [ABSTRACT FROM AUTHOR]

This paper aims to explore the enhancement effect of spiral stirrup on concrete-filled cold-formed steel built-up box (CF-CFB) columns. Herein, four specimens were designed and fabricated to explore the impact of the spiral stirrup and riveted form on the axial compression performance of CF-CFB columns. Then, the finite element model of spiral stirrup-reinforced concrete-filled cold-formed steel built-up box (RCF-CFB) stub columns was established, and a systemic parametric investigation was conducted to explore the impact of geometric and material parameters on the compression performance of RCF-CFB stub columns. Afterwards, the analysis included an assessment of contact stress and stress distribution was conducted to uncover the confining effect. The analysis results revealed that the failure mode of the RCF-CFB column was tube buckling and concrete crush, accompanied by the spliced tube separating at the buckling area. The built-in reinforcement could significantly improve the performance of the built-up column, while riveted forms of spliced steel tubes had little effect. Furthermore, the axial bearing capacity of the RCF-CFB column would increase with the enhancement in steel yield strength, concrete strength, tube thickness, and longitudinal bar diameter. Finally, a calculating method to predict the axial bearing capacity of the RCF-CFB column was proposed, and the applicability of the method was demonstrated by comparison with experimental and FE data. • Compression tests were carried out on the performance of the concrete-filled cold-formed steel built-up box columns. • An analysis model of concrete-filled cold-formed steel built-up box stub columns was established and validated. • A practical method for predicting the axial compression load capacity was proposed. [ABSTRACT FROM AUTHOR]

This paper presented a series of tests to investigate the behaviour of the extended end-plate connection utilizing high strength Q960 steel. A total of 8 specimens were tested, including two under ambient temperature and three under high temperature. The results of the tests indicated that increasing the end-plate thickness from 8 mm to 12 mm significantly enhances the flexural capacity and initial rotational stiffness of the connections but reduces the critical temperature and ultimate rotation. In addition, a higher beam bending moment ratio was found to increase the ultimate rotation of the connections while having minimal impact on the critical temperature. Then, the finite element model of the connections was established to investigate the parametric effect, including column axial pressure ratio, beam bending moment ratio, and end-plate thickness on fire resistance. The numerical analysis indicated that increased column axial pressure ratio and end-plate thickness decreased fire endurance, critical temperature, and ultimate rotation of the connections. On the other hand, increasing the beam-bending moment ratio enhanced the ultimate rotation of the connections. Lastly, a rotation-temperature relationship model was proposed to accurately predict the temperature-rotation curve of high-strength steel Q960 end-plate connections, which was validated with experimental data. • Fire tests on response of high strength Q960 steel connections were carried out. • Numerical models were developed to simulate the behaviour of Q960 teel connections at elevated temperatures. • Parametric studies were performed to investigate the effect of key factors on fire resistance of the connections. • A rotation-temperature relationship model was proposed to predict the fire behaviour of Q960 steel connections. [ABSTRACT FROM AUTHOR]

• This paper applied the lightweight aggregate concrete (LWAC) into partially encased steel-concrete composite (PEC) stub columns. • The axial compression test was conducted to explore the work properties of partially encased steel-concrete composite stub columns with LWAC. • The finite element models of the PEC-LC column were established to conduct a systemic parametric investigation. • The axial strength calculation method of PEC-LC columns was proposed considering the flange strength reduction and core concrete enhancement. This paper applied lightweight aggregate concrete (LWAC) in the partially encased steel-concrete composite (PEC) stub columns to achieve the advantages of lightweight and easy assembly. A total of 8 axial-loaded specimens were tested to explore the effect of concrete type, concrete strength, link spacing, longitudinal rebars, and height-to-width ratio on the compressive behavior of the partially encased steel-concrete composite stub columns with lightweight aggregate concrete (PEC-LC). Then, the finite element models of PEC-LC columns were established to conduct a systemic parametric investigation. The results demonstrated that the PEC-LC column experienced failure due to concrete crushing and local buckling of flanges, similar to the PEC column. Compared to the PEC column, the PEC-LC column exhibited a similar load-bearing capacity but poorer post-peak compressive performance, which could be improved by closer link spacing. Consequently, applying LWAC to reduce the self-weight of prefabricated members is a feasible option. Besides, the contact stress and the stress distribution at typical cross-sections were analyzed to reveal the confinement effect of H-shaped steel and links on the filled LWAC. Finally, A calculation method for estimating the axial compression capacity of the PEC-LC column was proposed, taking into account the reduction in flange strength and enhancement of core concrete. The accuracy of the calculation method was verified by comparison with experimental and numerical data. Overall, this research serves as a valuable reference for promoting the adoption of the PEC-LC column in assembled structures. [ABSTRACT FROM AUTHOR]

To greatly facilitate hoisting and assembly of prefabricated partially encased steel-concrete composite (PEC) columns, lightweight aggregate concrete (LAC) is applied into the PEC columns to form the partially encased composite columns with lightweight aggregate concrete (PEC-LAC). This paper reported experimental studies on the axial compressive behavior of PEC-LAC columns with various slenderness ratios. Following this, finite element (FE) modeling methods considering geometrical and residual stress imperfections were developed to reproduce the test responses. FE analysis was carried out to investigate the effect of geometrical and material parameters on PEC-LAC slender columns subjected to axial compression along the minor axis and major axis. It was found from the contact stress analysis that PEC-LAC slender columns with axial loading along the major axis provide a stronger confinement effect than that with axial loading along the minor axis. Based on the comparison of reduction factors between the test/FE and calculated results, the buckling curve of AISC 360 and the buckling curve (b) of T/CECS 719 can economically and conservatively describe the buckling curve of PEC-LAC slender columns regardless of the flexural buckling direction; the buckling curves (b) and (a) of EC4 were recommended to predict buckling curves of PEC-LAC columns with flexural buckling about the major and minor axis, respectively. • The axial compressive behavior of PEC-LAC columns with various slenderness ratios was tested. • FE models for PEC-LAC columns were developed and the systemic parametric investigation was conducted. • The slenderness ratio limits for elastoplastic instability and elastic instability were revealed. • Some suggestions for predicting the buckling curves of PEC-LAC columns were presented. [ABSTRACT FROM AUTHOR]