Search

Acid mine drainage is an extraordinarily acidic and highly heavy metal ion-contaminated leachate, seriously threatening the environment. In this work, an industrial solid waste of steel slag is the adsorbent to remediate the simulated acid mine drainage containing a large amount of Fe(II) ions. Due to the excellent physicochemical properties and structures, steel slag exhibited remarkable Fe(II) removal performance. Its maximum removal efficiency was up to 100%. The initial pH, the dosage and particle size of steel slag, and initial concentration of heavy metal ions on Fe(II) removal efficiency were determined. The pseudo-second-order model and Freundlich isotherm model well described the adsorption behavior of steel slag, implying that the adsorption of Fe(II) by steel slag was mainly multilayer chemisorption. The thermodynamic study demonstrated that the adsorption process was endothermic and spontaneous; the enthalpy change was calculated to equal 91.21 kJ/mol. Mechanism study showed that the entire removal process of Fe(II) by steel slag was completed by electrostatic adsorption, chemical precipitation, and surface complexation in cooperation, and the chemical precipitation was the dominant mechanism. Meaningfully, this study provides a valuable strategy and path for engineering applications of AMD remediation by steel slag, which is prospective as an ideal candidate for Fe(II) ions elimination, inspiring the future development of "Treating the wastes with wastes."

To reduce the density of bamboo-based concrete formwork on the premise of meeting the performance requirements, the bamboo was first treated by cold plasma, and then by increasing the distance between the adjacent bamboo strips of the radial bamboo curtain in the middle layer, the internal porosity was increased. The production of lightened bamboo based concrete formwork, which meets China’s forestry industry standards, was achieved. Four groups of bamboo-based concrete formworks with different slab structures were designed. The key results showed that slab structures have an extremely significant effect on the density, MOR, MOE, IB, and TS of the bamboo-based concrete formwork. A group of optimal slab structures was obtained by comparing their physical and mechanical properties (1st and 9th floor-phenolic resin impregnated paper, 2nd and 8th floor-bamboo mat, 3rd and 7th floor-tangential bamboo curtain, 4th and 6th floor-radial spaced bamboo curtain). Based on the required physical and mechanical properties, its density was 0.62 g·cm-3, which was 27.1% lower than that of traditional bamboo plywood template (0.85 g·cm-3) circulating on the current market. This lightened BBCF can save raw materials, facilitate transportation and reduce labor intensity in the application process so that it will be widely used in building construction.

The dynamic adsorption isotherms of CO2-EGR were measured by using a Intelligent Gravimetric Analysis system.In the beginning stage of CO2 injection, all the injected CO2 enters into the adsorbent and the mole fraction of CH4 (yCH4) keeps 1.0. The CH4 recovery factor (RCH4) increases. The during of this stage (tcd) depends on the selectivity of CO2 over CH4 ( SCO2/CH4). A adsorbent with large SCO2/CH4 has long tCD. When SCO2/CH4 is greater than 1.0, CO2 reduces the fraction of CH4 in the adsorbed phase (xCH4) and more CH4 is driven out. In the second stage,the injected CO2 competes with CH4 for adsorption. The cumulative RCH4 of this stage is much larger than that of the initial stage. However, yCH4 decrease sharply. pCH4 in the whole CO2 injection is always larger than that before CO2 injection, suggesting CH4 desorption results from the displacement by CO2 rather than from pressure depletion.

The dynamic adsorption isotherms of CO2-EGR were measured by using a Intelligent Gravimetric Analysis system.In the beginning stage of CO2 injection, all the injected CO2 enters into the adsorbent and the mole fraction of CH4 (yCH4) keeps 1.0. The CH4 recovery factor (RCH4) increases. The during of this stage (tcd) depends on the selectivity of CO2 over CH4 ( SCO2/CH4). A adsorbent with large SCO2/CH4 has long tCD. When SCO2/CH4 is greater than 1.0, CO2 reduces the fraction of CH4 in the adsorbed phase (xCH4) and more CH4 is driven out. In the second stage,the injected CO2 competes with CH4 for adsorption. The cumulative RCH4 of this stage is much larger than that of the initial stage. However, yCH4 decrease sharply. pCH4 in the whole CO2 injection is always larger than that before CO2 injection, suggesting CH4 desorption results from the displacement by CO2 rather than from pressure depletion.

Poisoning effects by alkali metal chlorides is one of the major reasons for the deactivation of SCR catalyst in biomass-fired plants. In this study, the influence of KCl on two vanadium-based catalysts with different promoters, V2O5-WO3/TiO2 and V2O5-Ce(SO4)2/TiO2, was investigated. The catalytic activity of the fresh V2O5-WO3/TiO2 was higher than that of V2O5-Ce(SO4)2/TiO2 at low temperatures. V2O5-Ce(SO4)2/TiO2 performed better than V2O5-WO3/TiO2 when KCl was deposited on the catalyst surface. Both poisoned catalysts were efficiently regenerated by SO2 treatment. The characterization results show that the reducibility and acidity of the catalysts were weakened by KCl deposition but regenerated by SO2.

The overlaid laminated bamboo lumber (OLBL) was developed for structural applications with an aim to substitute commonly-used building materials such as steel and concrete. The OLBL was, via a hot press, fabricated by cross-laminating bamboo layers, bamboo mats and phenolic impregnated adhesive papers. Since the weight of OLBL was governed by the high density bamboo layer, the panels made of OLBL had a relatively high density value of about 850 kg/m3. In this study, a lightweight panel was developed by a proper arrangement of radial bamboo curtain. The major and minor directions of a panel were the parallel- and perpendicular-to-its length direction, respectively. It was found that 1) the density of an OLBL panel could be reduced by about 20%; 2) the failure occurred in the bamboo node(s); 3) there was a significant difference in effective modulus of elasticity and effective modulus of rupture between two panel directions; and 4) there was a good relationship between the density and strength in the minor direction.

Studying the heat transfer characteristics of alternating current (AC) arc-fault to electrodes is a key issue in electrical fires. In this paper, an instantaneous heat transfer numerical model of AC arc-fault is developed based on the magneto-hydrodynamic principle. The temperature distribution of the AC arc at the microseconds level and the influence of heat transfer on electrodes at the seconds level when the arc heats are studied. The numerical simulation of the axial temperature of the electrodes is verified by experiments, and the temperature variation in the electrodes at different currents and times is discussed. The results show that the arc temperature varies periodically similar to the current at the microseconds level but it does not go out when the current passes zero. The high-temperature region of electrodes diffuses with the increase in current or time. However, the axial temperature gradient of the electrode decreases with time and increases with current. Furthermore, the range of temperature increase in the electrode position decreases with the increase in current and time, but the electrode position near the arc has a higher initial temperature increase.

Coal is still a major energy source, mostly used in power plants. However, the coal combustion emits harmful SO 2 and fly ash. Wet flue gas desulfurization (WFGD) technology is extensively used to control SO 2 emissions in power plants. However, only limited studies have investigated the synergistic dust removal by the WFGD system. Spray scrubbers and sieve-tray spray scrubbers are often used in WFGD systems to improve the SO 2 removal efficiency. In this study, the synergistic dust removal of WFGD systems for a spray scrubber and a sieve-tray spray scrubber was investigated using the experimental and modelling approaches, respectively. For the spray scrubber, the influence of parameters, including dust particle diameters and inlet concentrations of dust particles, and the flow rates of flue gas and slurry of limestone/gypsum on the dust removal efficiency, was investigated. For the sieve-tray spray scrubber, the influence of parameters such as the pore diameter and porosity of sieve trays on the dust removal efficiency was examined. The study found that the dust removal efficiency in the sieve-tray spray scrubber was approximately 1.1–10.6% higher than that of the spray scrubber for the same experimental conditions. Based on the parameters investigated and geometric parameters of a scrubber, a novel droplets swarm model for dust removal efficiency was developed from the single droplet model. The enhanced dust removal efficiency of sieve tray was expressed by introducing a strength coefficient to an inertial collision model. The dust removal efficiency model for the sieve-tray spray scrubber was developed by combining the droplets swarm model for the spray scrubber with the modified inertial collision model for the sieve tray. The results simulated using both models are consistent with the experimental data obtained.

To improve the reuse rate of bamboo materials, laminated bamboo lumber (LBL) with high bond strength has been developed for structural use using bamboo residues (BRs). The laminated structure design is an important factor affecting LBL performance, and thus, it is essential to study various LBL blank structures. The major direction is parallel to the panel length, and the minor direction is perpendicular to the panel length. In this study, BRs were cut into A and B units along the major and minor directions, respectively. The LBL with good performance was selected by different forming methods and modified by O2 plasma. It was found that 1) the volume utilization rate of BRs in LBL is above 85%; 2) the wet bonding strength of LBL products is increased by 58.58% compared to ordinary plywood, when the O2 plasma modification time is 6 min and 12 min respectively, the wet bonding strength is increased by 75.69% and 76.27% compared to ordinary plywood; 3) when bamboo pieces are arranged in parallel, the modulus of rupture in the major direction is ~ 2 times greater than in the minor direction, while a staggered arrangement can effectively reduce the bamboo anisotropic effect; 4) the destruction of LBL mainly occurs at the joints; 5) after O2 plasma modification, the wettability of green bamboo and yellow bamboo was significantly improved, followed by bamboo flesh.

The purpose of the present study was to investigate the effect of the A(2A) receptor antagonist (SCH 442416) on the mRNA expression of glutamate aspartate transporter (GLAST) and glutamine synthetase (GS) in rat retinal Müller cells under hypoxic conditions in vitro. Immunofluorescent staining of GS and GFAP was used for the identification of Müller cells. The GLAST and GS mRNA expression of Müller cells treated with 0.1, 1 and 10 μM SCH 442416 under hypoxic conditions was examined by real-time PCR. Müller cells increased the mRNA expression of GLAST under hypoxic conditions; those treated with 0.1 μM SCH 442416 showed a further significant increase in the mRNA expression of GLAST in vitro. Although the mRNA expression of GS was decreased under hypoxic conditions, the mRNA expression was increased when Müller cells were treated with 0.1 μM SCH 442416. A(2A) receptor antagonist increased the GLAST and GS expression of Müller cells and accelerated the clearance of extracellular glutamate under hypoxic conditions in vitro.

The aim of this study was to investigate the expression of Kir 2.1 and Kir 4.1 channels at an elevated hydrostatic pressure in vitro, and to determine whether adenosine may modulate the mRNA expression of Kir 2.1 and Kir 4.1 channels in retinal Müller cells at an elevated hydrostatic pressure in vitro. Müller cells treated with 1 μM adenosine at 40 mmHg/24 h, and mRNA expression of Kir 2.1 and Kir 4.1 channels were examined using real-time PCR. Müller cells significantly increased the mRNA expression of Kir 2.1 and Kir 4.1 channels at 40 mmHg/24 h. When further treated with 1 μM adenosine at 40 mmHg/24 h, the mRNA expression of the Kir 2.1 channels decreased, while the mRNA expression of the Kir 4.1 channels continued to increase. When the pressure was elevated, Müller cells were still able to take up K(+) and mediate the potassium concentration of the retina. Adenosine upregulated the expression of the Kir 4.1 channels, but weakly affected the expression of the Kir 2.1 channels.

The diagnosis of Duchenne muscular dystrophy (DMD) has historically utilized either PCR or requires Southern blot analysis, a southern blot analysis, however, is not amenable to incorporation in a microdevice format. A PCR amplification-based method has been developed, and we have previously coupled this amplification with microchip separation of the PCR fragments for DMD diagnosis. Diagnoses of affected patients were performed by comparing exon concentrations to those of control samples amplified at the same time. To accurately identify mutations in patient samples, this work established normal ranges for the concentration of each amplified exon fragment using control samples amplified over successive days. Our studies show that the number of cycles used in the amplification process affects this range. Affected patient samples were analyzed using these normal ranges and the mutations detected by Southern blot analysis were also diagnosed using the microchip separation method. Employing the microchip separation method decreases the time required for the analysis, but the time required for DNA purification and PCR amplification must also be decreased for faster total analysis of patient samples. Development of microchip methods for these processing steps is one approach for reducing the individual times, while also providing the possibility of integrating these steps in a single device. Here we report on the microchip extraction of genomic DNA from whole blood using a novel sol–gel matrix that is easily formed in microdevices. IR-mediated PCR amplification of a β-globin fragment from genomic DNA followed by electrophoretic analysis on a single integrated microdevice is presented for the first time. Work towards the development of a micro-total analysis device for DMD diagnosis, through integration of all processing steps on a single device, is also discussed.

Two novel polysiloxanes containing the metal complex, Co(TACN)(3+)2 (TACN= 1,4,7-triazacyclononane) were used as coatings for capillary electrophoresis (CE) and capillary electrochromatography (CEC). Through crosslinking and covalent bonding, the positively charged polymers were bonded to silica supports. In both CE and CEC, these coatings exhibited strong, pH-independent, and anodic electroosmotic flow (EOF), and had excellent long-term stability. Successful separations of aromatic acids were achieved in CE. In CEC, separation of alkylbenzenes (7 min) and basic compounds (20 min) was achieved with higher resolving power than conventional octadecyl silica packings. These polymers represent a new class of coatings for CE and CEC that generate pH-independent EOF.

Two novel polysiloxane-based polymers, which contain metal complexes, have been prepared. To prepare the Co(TACN)3+(2) (TACN= 1,4,7-triazacyclononane) based polymers, an orthoamide derivative of TACN was added to bromobutane-substituted methylpolysiloxane and hydrolyzed with base. Co(II) was then coordinated to the TACN, followed by cobalt oxidation to make polymer A or followed by N-octyl TACN coordination and cobalt oxidation to make polymer B. In both materials, TACN forms thermodynamically and kinetically stable Co(TACN)3+(2) complexes in which the six coordination sites of the Co(III) are occupied by nitrogens from the TACN. The polymers were coated on fused-silica capillary columns and spherical silica particles, which were used for capillary electrophoresis and capillary electrochromatography, respectively. The open and packed columns showed strong and pH-independent reversed electroosmotic flow.

Effective microchip extraction of deoxyribonucleic acid (DNA) from crude biological matrixes has been demonstrated using silica beads or hybrid phases composed of beads and sol-gel. However, the use of monolithic sol-gels alone for extraction of human genomic DNA has been more difficult to define. Here we describe, for the first time, the successful use of monolithic tetramethyl orthosilicate-based sol-gels for effective micro-solid-phase extraction (muSPE) of DNA in a glass microchip format. A functional monolithic silica phase with micrometer-scale pores in the silica matrix resulted from addition of poly(ethylene glycol), a poragen, to the precursor mixture. This allowed a monolithic sol-gel bed to be established in a microchip channel that provided large surface area for DNA extraction with little flow-induced back pressure. DNA extraction efficiencies for simple systems (lambda-phage DNA) were approximately 85%, while efficiencies for the reproducible extraction of human genomic DNA from complex biological matrixes (human blood) were approximately 70%. Blockage of the sol-gel pores by components in the lysed blood was observed in repeat extraction on a single device as a decrease in the extraction efficiency. The developed muSPE protocol was further evaluated to show applicability to clinical samples and bacterial cultures, through extraction of PCR-amplifiable DNA.

The feasibility of using monolithic sol-gels for micro-solid phase extraction (μSPE) of deoxyribonucleic acid (DNA) in a microchip format is explored in this work. The monolithic sol-gel bed in a microchip allows efficient DNA purification and extraction with back pressures that are significantly lower than a particle-packed extraction bed. The applicability of the developed μSPE DNA extraction protocol to clinical samples, for example blood and serum, is successfully demonstrated.