Search

Floating offshore wind (FOW) is a renewable energy source that is set to play an essential role in addressing climate change and the need for sustainable development. However, due to the increasing threat of climate emergency, more wind turbines are required to be deployed in deep water locations, further offshore. This presents heightened challenges for accessing the turbines and performing maintenance, leading to increased costs. Naturally, methods to reduce operational expenditure (OpEx) are highly desirable. One method that shows potential for reducing OpEx of FOW is LIDAR‐assisted pitch control. This approach uses wind velocity measurements from a nacelle‐mounted LIDAR to enable feedforward control of floating offshore wind turbines (FOWTs) and can result in reductions to the variations of structural loads. Results obtained from a previous study of combined feedforward collective and individual pitch control (FFCPC + FFIPC) are translated to OpEx reductions via reduced component failure rates for future FOW developments, namely, in locations awarded in the recent ScotWind leasing round. The results indicate that LIDAR‐assisted pitch control may allow for an up to 5% reduction in OpEx, increasing to up to 11% with workability constraints included. The results varied across the three ScotWind sites considered, with sites furthest from shore reaping the greatest benefit from LIDAR‐assisted control. This work highlights the potential savings and reduction in the overall levelised cost of energy for future offshore wind turbine projects deliverable through the implementation of LIDAR‐assisted pitch control. [ABSTRACT FROM AUTHOR]

The practical aspect of human developmental biology education is often limited to the observation and use of animal models to illustrate developmental anatomy. This is due in part to the difficulty of accessing human embryonic and fetal specimens, and the sensitivity inherent to presenting these specimens as teaching materials. This report presents a new approach using three-dimensional (3D) printed replicas of actual human materials in practical classes, thus allowing for the inclusion of accurate examples of human developmental anatomy in the educational context. A series of 3D prints have been produced from digital data collected by computed tomography (CT) imaging of an archived series of preserved human embryonic and fetal specimens. The final versions of 3D prints have been generated in a range of single or multiple materials to illustrate the progression of human development, including the development of internal anatomy. Furthermore, multiple copies of each replica have been printed for large group teaching. In addition to the educational benefit of examining accurate 3D replicas, this approach lessens the potential for adverse student reaction (due to cultural background or personal experience) to observing actual human embryonic/fetal anatomical specimens, and reduces the potential of damage or loss of original specimens. This approach, in combination with ongoing improvements in the management and analysis of digital data and advances in scanning technology, has enormous potential to allow embryology students access to both local and international collections of human gestational material.

Nacelle‐mounted, forward‐facing light detection and ranging (LIDAR) technology can deliver benefits to rotor speed regulation and loading reductions of floating offshore wind turbines (FOWTs) when assisting with blade pitch control in above‐rated wind speed conditions. Large‐scale wind turbines may be subject to significant variations in structural loads due to differences in the wind profile across the rotor‐swept area. These loading fluctuations can be mitigated by individual pitch control (IPC). This paper presents a novel LIDAR‐assisted feedforward IPC approach that uses each blade's rotor azimuth position to allocate an individual pitch command from a multi‐beam LIDAR. In this study, the source code of OpenFAST wind turbine modelling software was modified to enable LIDAR simulation and LIDAR‐assisted control. The LIDAR simulation modifications were accepted by the National Renewable Energy Laboratory (NREL) and are now present within OpenFAST releases from v3.5 onwards. Simulations of a 15 MW FOWT were performed across the above‐rated wind spectrum. Under a turbulent wind field with an average wind speed of 17 ms−1, the LIDAR‐assisted feedforward IPC delivered up to 54% reductions in the root mean squared errors and standard deviations of key FOWT parameters. Feedforward IPC delivered enhancements of up to 12% over feedforward collective pitch control, relative to the baseline feedback controller. The reductions to the standard deviation and range of the rotor speed may enable structural optimization of the tower, while the reductions in the variations of the loadings present an opportunity for reduced fatigue damage on turbine components and, consequently, a reduction in maintenance expenditure. [ABSTRACT FROM AUTHOR]

The teaching of anatomy has consistently been the subject of societal controversy, especially in the context of employing cadaveric materials in professional medical and allied health professional training. The reduction in dissection-based teaching in medical and allied health professional training programs has been in part due to the financial considerations involved in maintaining bequest programs, accessing human cadavers and concerns with health and safety considerations for students and staff exposed to formalin-containing embalming fluids. This report details how additive manufacturing or three-dimensional (3D) printing allows the creation of reproductions of prosected human cadaver and other anatomical specimens that obviates many of the above issues. These 3D prints are high resolution, accurate color reproductions of prosections based on data acquired by surface scanning or CT imaging. The application of 3D printing to produce models of negative spaces, contrast CT radiographic data using segmentation software is illustrated. The accuracy of printed specimens is compared with original specimens. This alternative approach to producing anatomically accurate reproductions offers many advantages over plastination as it allows rapid production of multiple copies of any dissected specimen, at any size scale and should be suitable for any teaching facility in any country, thereby avoiding some of the cultural and ethical issues associated with cadaver specimens either in an embalmed or plastinated form.

The teaching of medical pathology has undergone significant change in the last 30–40 years, especially in the context of employing bottled specimens or 'pots' in classroom settings. The reduction in post-mortem based teaching in medical training programs has resulted in less focus being placed on the ability of students to describe the gross anatomical pathology of specimens. Financial considerations involved in employing staff to maintain bottled specimens, space constraints and concerns with health and safety of staff and student laboratories have meant that many institutions have decommissioned their pathology collections. This report details how full-colour surface scanning coupled with CT scanning and 3 D printing allows the digital archiving of gross pathological specimens and the production of reproductions or replicas of preserved human anatomical pathology specimens that obviates many of the above issues. With modern UV curable resin printing technology, it is possible to achieve photographic quality accurate replicas comparable to the original specimens in many aspects except haptic quality. Accurate 3 D reproductions of human pathology specimens offer many advantages over traditional bottled specimens including the capacity to generate multiple copies and their use in any educational setting giving access to a broader range of potential learners and users. [ABSTRACT FROM AUTHOR]