Search

Due to the volume expansion effect during charge and discharge processes, the application of transition metal oxide anode materials in lithium-ion batteries is limited. Composite materials and carbon coating are often considered feasible improvement methods. In this study, three types of TiO2@Fe3O4@C microspheres with a core–double-shell structure, namely TFCS (TiO2@Fe3O4@C with 0.0119 g PVP), TFCM (TiO2@Fe3O4@C with 0.0238 g PVP), and TFCL (TiO2@Fe3O4@C with 0.0476 g PVP), were prepared using PVP (polyvinylpyrrolidone) as the carbon source through homogeneous precipitation and high-temperature carbonization methods. After 500 cycles at a current density of 2 C, the specific capacities of these three microspheres are all higher than that of TiO2@Fe2O3 with significantly improved cycling stability. Among them, TFCM exhibits the highest specific capacity of 328.3 mAh·g−1, which was attributed to the amorphous carbon layer effectively mitigating the capacity decay caused by the volume expansion of iron oxide during charge and discharge processes. Additionally, the carbon coating layer enhances the electrical conductivity of the TiO2@Fe3O4@C materials, thereby improving their rate performance. Within the range of 100 to 1600 mA·g−1, the capacity retention rates for TiO2@Fe2O3, TFCS, TFCM, and TFCL are 27.2%, 35.2%, 35.9%, and 36.9%, respectively. This study provides insights into the development of new lithium-ion battery anode materials based on Ti and Fe oxides with the abundance and environmental friendliness of iron, titanium, and carbon resources in TiO2@Fe3O4@C microsphere anode materials, making this strategy potentially applicable. [ABSTRACT FROM AUTHOR]

Thermoelectric materials have drawn much attention over the last two decades due to the increase in global energy demand. However, designing efficient thermoelectrics reveals itself as a tough task for their properties (Seebeck coefficient, electrical conductivity, thermal conductivity) are mutually opposed. Hence, most recently, new design approaches have appeared, among which high-throughput methods have been implemented either experimentally or computationally. In this work, a high-throughput computer program has been designed to generate over 4000 structures based on a small set of complex layered chalcogenide compounds taken from the mAIVBVI nA2VB3VI homologous series, where AIV is Ge, AV is Sb and BVI is Te. The computer-generated structures have been investigated using density-functional theory methods, and the electronic and transport properties have been calculated. It has been found, using the quantum theory of atoms in molecules and crystals, that a wide variety of bond types constitutes the bonding network of the structures. All the structures are found to have negative formation energies. Among the obtained final structures, 43 are found with a wide band gap energy (>0.25 eV), 358 with semi-conductor/metal characteristics, and 731 with metallic characteristics. The transport properties calculations, using the Boltzmann equation, reveal that two p-type and 86 n-type structures are potentially promising compounds for thermoelectric applications. [ABSTRACT FROM AUTHOR]

In recent years, layered chalcogenides have attracted interest for their appealing thermoelectric properties. We investigated the Ge2Sb2Te5 compound in two different stacking sequences, named stacking 1 (S1) and stacking 2 (S2), wherein the Ge and Sb atomic positions can be interchanged in the structure. The compound unit cell, comprising nine atoms, is made of two layers separated by a gap. We show, using the quantum theory of atoms in molecules, that the bonding across the layers has characteristics of transit region bonding, though with a close resemblance to closed-shell bonding. Both S1 and S2 are shown to bear a similar small gap. The full determination of their thermoelectric properties, including the Seebeck coefficient, electrical conductivity and electronic and lattice thermal conductivities, was carried out by solving the Boltzmann transport equation. We show that stacking 1 exhibits a larger Seebeck coefficient and smaller electrical conductivity than stacking 2, which is related to their small electronic gap difference, and that S1 is more suitable for thermoelectric application than S2. Moreover, under certain conditions of temperature and doping level, it could be possible to use S1-Ge2Sb2Te5 as both a p and n leg in a thermoelectric converter. Under biaxial, tensile and compressive strains, we observe that the thermoelectric properties are improved for both S1 and S2. Furthermore, the increase in the power factor of S1 in the cross-plane direction, namely perpendicular to the gap between the layers, shows that strains can counteract the electronic transport hindrance due to the gap. [ABSTRACT FROM AUTHOR]

A single crystalline layered semiconductor In1.2Ga0.8S3 phase was grown, and by intercalating p-aminopyridine (NH2-C5H4N or p-AP) molecules into this crystal, a new intercalation compound, In1.2Ga0.8S3·0.5(NH2-C5H4N), was synthesized. Further, by substituting p-AP molecules with p-ethylenediamine (NH2-CH2-CH2-NH2 or p-EDA) in this intercalation compound, another new intercalated compound—In1.2Ga0.8S3·0.5(NH2-CH2-CH2-NH2) was synthesized. It was found that the single crystallinity of the initial In1.2Ga0.8S3 samples was retained after their intercalation despite a strong deterioration in quality. The thermal peculiarities of both the intercalation and deintercalation of the title crystal were determined. Furthermore, the unit cell parameters of the intercalation compounds were determined from X-ray diffraction data (XRD). It was found that increasing the c parameter corresponded to the dimension of the intercalated molecule. In addition to the intercalation phases' experimental characterization, the lattice dynamical properties and the electronic and bonding features of the stoichiometric GaInS3 were calculated using the Density Functional Theory within the Generalized Gradient Approximations (DFT-GGA). Nine Raman-active modes were observed and identified for this compound. The electronic gap was found to be an indirect one and the topological analysis of the electron density revealed that the interlayer bonding is rather weak, thus enabling the intercalation of organic molecules. [ABSTRACT FROM AUTHOR]

In this study, lychee-like TiO2@Fe2O3 microspheres with a core-shell structure have been prepared by coating Fe2O3 on the surface of TiO2 mesoporous microspheres using the homogeneous precipitation method. The structural and micromorphological characterization of TiO2@Fe2O3 microspheres has been carried out using XRD, FE-SEM, and Raman, and the results show that hematite Fe2O3 particles (7.05% of the total mass) are uniformly coated on the surface of anatase TiO2 microspheres, and the specific surface area of this material is 14.72 m2 g−1. The electrochemical performance test results show that after 200 cycles at 0.2 C current density, the specific capacity of TiO2@Fe2O3 anode material increases by 219.3% compared with anatase TiO2, reaching 591.5 mAh g−1; after 500 cycles at 2 C current density, the discharge specific capacity of TiO2@Fe2O3 reaches 273.1 mAh g−1, and its discharge specific capacity, cycle stability, and multiplicity performance are superior to those of commercial graphite. In comparison with anatase TiO2 and hematite Fe2O3, TiO2@Fe2O3 has higher conductivity and lithium-ion diffusion rate, thereby enhancing its rate performance. The electron density of states (DOS) of TiO2@Fe2O3 shows its metallic nature by DFT calculations, revealing the essential reason for the high electronic conductivity of TiO2@Fe2O3. This study presents a novel strategy for identifying suitable anode materials for commercial lithium-ion batteries. [ABSTRACT FROM AUTHOR]

Thermoelectric materials have attracted extensive attention because they can directly convert waste heat into electric energy. As a brand-new method of alloying, high-entropy alloys (HEAs) have attracted much attention in the fields of materials science and engineering. Recent researches have found that HEAs could be potentially good thermoelectric (TE) materials. In this study, special quasi-random structures (SQS) of PbSnTeSe high-entropy alloys consisting of 64 atoms have been generated. The thermoelectric transport properties of the highest-entropy PbSnTeSe-optimized structure were investigated by combining calculations from first-principles density-functional theory and on-the-fly machine learning with the semiclassical Boltzmann transport theory and Green–Kubo theory. The results demonstrate that PbSnTeSe HEA has a very low lattice thermal conductivity. The electrical conductivity, thermal electronic conductivity and Seebeck coefficient have been evaluated for both n-type and p-type doping. N-type PbSnTeSe exhibits better power factor (PF = S2σ) than p-type PbSnTeSe because of larger electrical conductivity for n-type doping. Despite high electrical thermal conductivities, the calculated ZT are satisfactory. The maximum ZT (about 1.1) is found at 500 K for n-type doping. These results confirm that PbSnTeSe HEA is a promising thermoelectric material. [ABSTRACT FROM AUTHOR]

In this study, 20Li2O-60V2O5-(20 − x)B2O3-xBi2O3 (x = 5, 7.5, 10 mol%) glass materials have been prepared by the melt-quenching method, and the structure and morphology of the glass materials have been characterized by XRD, FTIR, Raman, and FE-SEM. The results show that the disordered network of the glass is mainly composed of structural motifs, such as VO4, BO3, BiO3, and BiO6. The electrochemical properties of the glass cathode material have been investigated by the galvanostatic charge-discharge method and cyclic voltammetry, and the results show that with the increases of Bi2O3 molar content, the amount of the VO4 group increases, and the network structure of the glass becomes more stable. To further enhance the electrochemical properties, glass-ceramic materials have been obtained by heat treatment, and the effect of the heat treatment temperature on the structure and electrochemical properties of the glass has been studied. The results show that the initial discharge capacity of the glass-ceramic cathode obtained by heat treatment at 280 °C at a current density of 50 mA·g−1 is 333.4 mAh·g−1. In addition, after several cycles of charging and discharging at a high current density of 1000 mA·g−1 and then 10 cycles at 50 mA·g−1, its discharge capacity remains at approximately 300 mAh·g−1 with a capacity retention rate of approximately 90.0%. The results indicate that a proper heat treatment temperature is crucial to improving the electrochemical properties of glass materials. This study provides an approach for the development of new glass cathode materials for lithium-ion batteries. [ABSTRACT FROM AUTHOR]