Search

The launch of Landsat 9 (L9) on 27 September 2021 marks the ongoing commitment of the Landsat mission to delivering users with calibrated Earth observations for fifty years. The two imaging sensors on L9 are the Thermal Infrared Sensor-2 (TIRS-2) and the Operational Land Imager-2 (OLI-2). Shortly after launch, the image data from OLI-2 and TIRS-2 were evaluated for both radiometric and geometric quality. This paper provides a synopsis of the evaluation of the spatial response of the TIRS-2 instrument. The assessment focuses on determining the instrument’s ability to detect a perfect knife edge. The spatial response was evaluated both pre- and post-launch. Pre-launch testing was performed at NASA Goddard Space Flight Center (GSFC) under flight-like thermal vacuum (TVAC) conditions. On orbit, coastline targets were identified to evaluate the spatial response and compared against Landsat 8 (L8). The pre-launch results indicate that the spatial response of the TIRS-2 sensor is consistent with its predecessor on board L8, with no noticeable decline in image quality to compromise any TIRS science objectives. Similarly, the post-launch analysis shows no apparent degradation of the TIRS-2 focus during the launch and the initial operational timeframe.

With the launch of Landsat-9 on 27 September 2021, Landsat continues its fifty-year continuity mission of providing users with calibrated Earth observations. It has become a requirement that an underflight experiment be performed during commissioning to support sensor cross-calibration. In this most recent experiment, Landsat-9 flew under Landsat-8 for nearly three days with over 50% ground overlap, from 13 to 15 November 2021. To address the scarcity of reference data that are available to support calibration and validation early-on in the mission, a ground campaign was planned and executed by the Rochester Institute of Technology (RIT) on 14 November 2021 to provide full spectrum measurements for early mission comparisons. The primary experiment was conducted in the Outer Banks, North Carolina at Jockey’s Ridge Sand Dunes. Full-spectrum ground-based measurements were acquired with calibrated reference equipment, while a novel Unmanned Aircraft System (UAS)-based platforms acquired hyperspectral visible and near-infrared (VNIR)/Short-wave infrared (SWIR) imagery data and coincident broadband cooled thermal infrared (TIR) imagery. Results of satellite/UAS/ground comparisons were an indicator, during the commissioning phase, that Landsat-9 is behaving consistently with Landsat-8, ground reference, and UAS measurements. In the thermal infrared, all measurements agree to be within 1 K over water and to within 2 K over sand, which represents the most challenging material for estimating surface temperature. For the surface reflectance product(s), Landsat-8 and -9 are in good agreement and only deviate slightly from ground reference in the SWIR bands; a deviation of 2% in the VNIR and 5–8% in the SWIR regime. Subsequent longer-term studies indicate that Landsat 9 continues to perform as expected. The behavior of Thermal Infrared Sensor-2 (TIRS-2) against reference is also shown for the first year of the mission to illustrate its consistent performance.

Land Surface Temperature (ST) represents the radiative temperature of the Earth’s surface and is used as input to hydrological, agricultural, and meteorological science applications. Due to the synoptic nature of satellite imaging systems, ST products derived from space-borne platforms are invaluable for estimating ST at the local, regional, and global scale. In the past two decades, an emphasis has been placed on the need to develop algorithms necessary to deliver accurate surface temperature products to support the needs of science users. However, corresponding efforts to validate these products are hindered by the availability of quality ground-based reference measurements. The NOAA Surface Radiation Budget (SURFRAD) network is commonly used to support ST validation efforts, but their instrumentation is broadband (4−50 μ m) and several of their sites lack spatial uniformity. To address the apparent deficiencies within existing validation networks, this work discusses a prototype radiometer that was developed to provide surface temperature estimates to support validation efforts for spaceborne thermal instruments. Specifically, a prototype radiometer was designed, built, and calibrated to acquire ground reference data to be used to validate ST product(s) derived from Landsat 8 image data. Lab-based efforts indicate that these prototype instruments are accurate to within 1.28 K and initial field measurements demonstrate agreement to Landsat-derived ST products to within 1.37 K.

The split window technique has been used for over thirty years to derive surface temperatures of the Earth with image data collected from spaceborne sensors containing two thermal channels. The latest NASA/USGS Landsat satellites contain the Thermal Infrared Sensor (TIRS) instruments that acquire Earth data in two longwave infrared bands, as opposed to a single band with earlier Landsats. The United States Geological Survey (USGS) will soon begin releasing a surface temperature product for Landsats 4 through 8 based on the single spectral channel methodology. However, progress is being made toward developing and validating a more accurate and less computationally intensive surface temperature product based on the split window method for Landsat 8 and 9 datasets. This work presents the progress made towards developing an operational split window algorithm for TIRS. Specifically, details of how the generalized split window algorithm was tailored for the TIRS sensors are presented, along with geometric considerations that should be addressed to avoid spatial artifacts in the final surface temperature product. Validation studies indicate that the proposed algorithm is accurate to within 2 K when compared to land-based measurements and to within 1 K when compared to water-based measurements, highlighting the improved accuracy that may be achieved over the current single-channel methodology being used to derive surface temperature in the Landsat Collection 2 surface temperature product. Surface temperature products using the split window methodologies described here can be made available upon request for testing purposes.