Search

The challenges commonly associated with conventional high pressure die casting (HPDC) have led to increased interest in semi-solid metal (SSM) forming processes. In the present study, semi-solid slurries of A356 alloy prepared by the Swirled Enthalpy Equilibration Device (SEED) process were used for manufacturing components with complex shape by using a high pressure die casting machine. The segregation phenomenon and the effect of heat treatment on the microstructure evolution and mechanical properties were investigated. The results showed that the alloy consists of primary spherical α-Al grains, secondary solidified α-Al grains, eutectic Si, iron-rich intermetallic phases and low porosities. The microstructural investigations revealed that the eutectic Si particles underwent fragmentation, spheroidization and coarsening with increasing solution temperature. Furthermore, the solution treatment results in the dissolution of the π-Al8FeMg3Si6 phase and the growth of the β-Al5FeSi phase. The hardening peaks at 170 °C could be obtained with ageing for 5 h. Due to both solution and precipitation strengthenings, the yield strength, ultimate tensile strength and hardness of A356 alloy after heat treatment increase significantly compared to those in the as-rheocast state: they reach 266 MPa, 343 MPa and 110 HV0.2, respectively. The analysis of fracture surfaces of rheo-HPDC samples in both the as-rheocast and the heat-treated states revealed a mixed mechanism of dimples and quasi-cleavage. The microstructure inside the part was found to be quasi-homogeneous while the segregation phenomenon in different zones of the part is affected by die geometry during the filling process. The results imply that the SEED-HPDC process has the potential to be industrialized by implementing appropriate heat treatments for producing complex components with good mechanical properties.

Copyright of Progress in Physics of Metals / Uspehi Fiziki Metallov is the property of G.V. Kurdyumov Institute for Metal Physics, N.A.S.U and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

The microstructures, mechanical properties, thermal conductivities, and corrosion behavior of novel high-thermal-conductivity hypoeutectic Al-Si alloys, prepared by rheological high-pressure die-casting (Rheo-HPDC) and HPDC, were investigated and compared. The microstructure of the Rheo-HPDC alloy, including the primary α-Al (α 1 ), secondary α-Al (α 2 -Al), β-Al 5 FeSi, and Si phases, was significantly more refined than that of the HPDC alloy. Compared to the HPDC alloy, the Rheo-HPDC alloy exhibited superior mechanical properties and thermal conductivity, and its ultimate tensile strength (UTS), yield strength (YS), elongation, hardness, and thermal conductivity were improved by 27%, 21%, 72%, 10% and 8%, respectively. Pitting corrosion of the Rheo-HPDC alloy was observed to originate at the interfaces between the Fe-rich intermetallics and the α 2 -Al particles. Corrosion was observed to propagate in the eutectic areas upon prolonged immersion in 3.5 wt% NaCl solution. Electrochemical testing, scanning Kelvin probe (SKP) measurements, and corrosion-morphology analyses reveal that the Rheo-HPDC alloy has better corrosion resistance, primarily due to the decrease in the potential difference between the Fe-rich intermetallics and the matrix, the refinement of the eutectic Si and intermetallics, and the decrease in the areal ratio of eutectic Si to α 2 -Al. [ABSTRACT FROM AUTHOR]

Microstructure, mechanical properties and corrosion behavior of a novel Al-8Si-Fe alloy fabricated by Rheo-HPDC were investigated. Compared with the HPDC alloy, the microstructure (α 1 /α 2 -Al, Si and β-Al 5 FeSi phases) of the alloy was greatly refined by Rheo-HPDC. The Rheo-HPDC alloy showed improved mechanical properties and thermal conductivity to those prepared by HPDC, and the increasing rates of UTS, YS, elongation, hardness and thermal conductivity were 31%, 19%, 59%, 12% and 10%, respectively. Rheo-HPDC Al-8Si-Fe alloy also indicated a significant improvement in corrosion resistance as demonstrated by the results of immersion, electrochemical and scanning kelvin probe (SCP) tests. [ABSTRACT FROM AUTHOR]

Cerium-based conversion coatings were deposited on Rheo-High Pressure Die Cast (HPDC) Al-Si alloys by immersion in cerium nitrate aqueous solutions. Rheocast Al-Si alloys have a heterogeneous microstructure and present a challenge for the conversion treatment. Different parameters were studied to optimize the conversion coating, and NaCl or H 2 O 2 were also added to the solution to modify or accelerate the deposition process. The mechanism of the coating formation was studied by means of focused ion beam milling (FIB) assisted SEM. The results show that applying cerium-based conversion coating to Al-Si alloys, is possible and a preferential deposition is obtained due to the presence of iron-rich intermetallic particles inside the eutectic region. The formation mechanism of selectively deposited cerium-based conversion coating includes dissolution of aluminium matrix, selective dissolution of aluminium from the noble intermetallic particles, oxidation of iron from the intermetallic particles, and the deposition of cerium hydroxide/oxide layer. The results reveal that the improvement in corrosion resistance in the presence of selectively deposited cerium-based conversion coating is more significant compared to the homogenous coating deposited from the conversion solution containing H 2 O 2 . [ABSTRACT FROM AUTHOR]

A simplified process, namely forced convection stirring (FCS), was proposed to prepare four different semisolid slurries of Al and Mg alloys. A simple rheological high pressure die-casting (Rheo-HPDC) process was developed by combining the FCS device with a HPDC machine. The temperature and composition fields of the melt in the FCS process were simulated. The microstructures and mechanical properties of the alloys formed by the FCS Rheo-HPDC were studied and compared with those formed by HPDC and other Rheo-HPDC processes. The results showed that the FCS process can prepare slurries in which the primary particles are fine, spherical and uniformly distributed in the matrix and the process can effectively suppress macrosegregation. The strong convection rapidly promotes the uniformity of the temperature and composition of the melt. Compared to HPDC and other Rheo-HPDC alloys, the alloys formed by FCS Rheo-HPDC have an improved ultimate tensile strength, yield strength, elongation and hardness, due to the refinement of microstructure and the decrease of porosity. Heat treatments can be utilized to further enhance the mechanical properties of FCS Rheo-HPDC alloys. [ABSTRACT FROM AUTHOR]

• A simple and efficient DCC process to prepare semisolid slurry was developed. • The semisolid viscosity model of A356 alloy was fitted. • The microstructure of the DCC Rheo-HPDC alloy was greatly refined compared to its HPDC analog. • DCC Rheo-HPDC alloy showed better mechanical properties than the HPDC alloy. • The nucleation mechanism and growth law of primary grain in DCC were clarified. A simple and efficient semisolid slurry preparation technique, called distributary-confluence channel (DCC), was developed to prepare high-quality semisolid slurries of aluminum and magnesium alloys. The DCC process was coupled with the use of a high pressure die-casting (HPDC) machine to successfully achieve near-net forming and implement production applications with rheological high pressure die-casting (Rheo-HPDC) for various Al and Mg alloy castings. The changes in the flow state and in the physical field of the melt during the slurry preparation via the DCC technique were investigated by numerical simulations. The nucleation mechanism and the growth law of the primary grain during the DCC process were discussed. The microstructures, porosities, and mechanical properties of the aluminum and magnesium alloys prepared via DCC Rheo-HPDC were studied. The results show that semisolid slurries containing a large amount of primary grains with an average size < 50 μm, a shape factor >0.8, and uniformly dispersed in the liquid matrix can be prepared via DCC. The simulation results indicate that the melt exhibits opposite velocity vectors on the upper part and on the lower part of the DCC. Moreover, it encounters and collides at the confluence to generate convection, which is beneficial to obtain uniform melt temperature, composition fields, nuclei exfoliation, and spherical growth. The random particle tracking simulation results show that the DCC process improves the composition field of the slurry. The DCC process facilitates the melt nucleation by using multi-channel chilling and increasing the nucleation area. The self-stirring generated during the flow of the melt produces a large amount of free nuclei inside the melt. There exist two main mechanisms behind the formation of the spherical primary grains. The one is the mechanism of explosive nucleation and spheroidal growth, the other is the dendrite arm necking, fusing, grain ripening, and rounding. Furthermore, by comparing identical alloy castings produced via traditional HPDC and other Rheo-HPDC processes, the DCC Rheo-HPDC castings present finer and rounder grains, a lower porosity, and more performant mechanical properties. [ABSTRACT FROM AUTHOR]

An air-cooled stirring rod (ACSR) process for efficiently preparing large volumes of semisolid slurry was introduced. A new low-cost casting Al–Si–Fe–Mg–Sr alloy was used to prepare large thin-walled heat-dissipating shells using both conventional HPDC and ACSR rheological high pressure die-casting (Rheo-HPDC) technologies. Their microstructures, thermal conductivities, elevated temperature and room temperature mechanical properties, and corrosion behaviors were compared. Furthermore, this work analyzed the mechanisms responsible for the microstructure refinement and performance enhancement in ACSR Rheo-HPDC alloys. The results showed that only 25 s was needed to prepare 32 kg of the semisolid slurry using ACSR process. The alloy prepared by ACSR Rheo-HPDC generated a large number of fine spherical primary α-Al particles with a volume fraction greater than 40%. The Rheo-HPDC alloy showed a moderate strength, high plasticity, and high heat conductivity. The heat conductivity, ultimate tensile strength and elongation of the Rheo-HPDC alloy were 184 W/(m.K), 264 MPa and 12.2% respectively, while those of the HPDC alloy were 167 W/(m.K), 228 MPa and 5.8% respectively. The improvement of heat conductivity of the alloy formed via ACSR Rheo-HPDC was mainly ascribed to the decrease of electron scattering by the refinement of eutectic silicons and Fe-rich intermetallics. This allowed the electron flow to pass through the eutectic Si region more easily. The refined and uniformly-distributed heat-resistant β-Al 5 FeSi intermetallics effectively prevented grain boundary sliding, so the Rheo-HPDC alloy showed superior high-temperature mechanical properties. The Rheo-HPDC alloy presented a more excellent corrosion resistance to the conventional HPDC alloy due to the refinement of iron-rich phase and eutectic silicons and the reduction in the potential difference between the matrix and the iron-rich phase. [ABSTRACT FROM AUTHOR]