Search

The development of new photoanode materials for hydrogen production and water treatment is in full progress. In this context, hybrid TiO2-Co3O4/Co(OH)2 photoanodes prepared using the sol–gel method using biosurfactants are currently being developed by our group. The combination of TiO2 with a cobalt-based compound significantly enhances the visible absorption and electrochemical performance of thin films, which is mainly due to an increase in the specific surface area and a decrease in the charge transfer resistance on the surface of the thin films. The formation of these composites allows for a 30-fold increase in the current density when compared to cobalt-free materials, with the best TiO2-CoN0.5 sample achieving a current of 1.570 mA.cm−2 and a theoretical H2 production rate of 0.3 µmol.min−1.cm−2 under xenon illumination. [ABSTRACT FROM AUTHOR]

A comparative study of the degradation of Direct Red 23 (DR23) dye aqueous solutions by electrooxidation was investigated using different anodes: carbon graphite (CG), dimensionally stable anode (DSA), Magnéli phase Ti4O7, and boron-doped diamond (BDD). Stainless steel (SS) and CG plates were tested as cathodes. The effect of operating parameters on the degradation kinetics of the dye was studied. In this study, NaCl and Na2SO4 were selected as supporting electrolytes; the former was found to be more suitable for the degradation of DR23. The degradation of the dye follows a pseudo-first-order kinetics in both media. Higher total organic carbon (TOC) efficiency was achieved by BDD/CG cells. Thus, the treatment efficiency obtained using a current density of 5 mA cm−2, and DR23 concentration of 60 mg L−1 was about 86% using both NaCl and Na2SO4 electrolyte, at 6 h electrolysis time. The energy consumptions per g TOC removed were found to be 2.05 and 2.6 kWh g−1 TOC in NaCl and Na2SO4 electrolytes, respectively. [ABSTRACT FROM AUTHOR]

Metal oxides and metal oxide/carbon composites are entering the development of new technologies and should therefore to be prepared by sustainable chemistry processes. Therefore, a new aspect of the reactivity of cellulose is presented through its solid/gas reaction with vapour of titanium(IV) chloride in anhydrous conditions at low temperature (80 °C). This reaction leads to two transformations both for cellulose and titanium(IV) chloride. A reductive dehydration of cellulose is seen at the lowest temperature ever reported and results in the formation of a carbonaceous fibrous solid as the only carbon-containing product. Simultaneously, the in situ generation of water leads to the formation of titanium dioxide with an unexpected nanoplate morphology (ca. 50 nm thickness) and a high photocatalytic activity. We present the evidence showing the evolution of the cellulose and the TiO2 nanostructure formation, along with its photocatalytic activity. This low-temperature process avoids any other reagents and is among the greenest processes for the preparation of anatase and also for TiO2/carbon composites. The anisotropic morphology of TiO2 questions the role of the cellulose on the growing process of these nanoparticles. [ABSTRACT FROM AUTHOR]

M-doped TiO2 and mixed oxides M xO y-TiO2 (M = V, Bi, W) were synthesized by the reactive mineralization of ash-free filter paper under anhydrous conditions. Mixtures of metal chlorides (TiCl4 with VOCl3, WCl6, or BiCl3) were reacted directly with cellulose, and three different Ti/M atomic ratios were used (99, 19, and 9). The resulting materials consist of original nanoflower assemblies of needle-shaped primary particles. Their physicochemical characteristics were investigated by various techniques (X-ray diffraction, diffuse-reflectance UV/Vis spectroscopy, electron microscopy, and elemental analysis). The incorporation of the doping metal or the formation of mixture of oxides with TiO2 (WO3, Bi2O3) depends on the metal and the proportions used. The photocatalytic activities of the materials were tested for the degradation of phenol. The vanadium-doped materials exhibit true solid-solution formation and their band gaps shift into the visible range. [ABSTRACT FROM AUTHOR]

The mineralization of tetracycline by electrochemical advanced oxidation processes (EAOPs) as well as the study of the toxicity of its intermediates and degradation products are presented. Electro-Fenton (EF), anodic oxidation (AO), and electro-Fenton coupled with anodic oxidation (EF/AO) were used to degrade tetracycline on carbon felt (cathode) and a sub-stoichiometric titanium oxide (Ti4O7) layer deposited on Ti (anode). As compared to EF and AO, the coupled EF/AO system resulted in the highest pollutant removal efficiencies: total organic carbon removal was 69 ± 1% and 68 ± 1%, at 20 ppm and 50 ppm of initial concentration of tetracycline, respectively. The effect of electrolysis current on removal efficiency, mineralization current efficiency, energy consumption, and solution toxicity of tetracycline mineralization were investigated for 20 ppm and 50 ppm tetracycline. The EF/AO process using a Ti4O7 anode and CF cathode provides low energy and high removal efficiency of tetracycline caused by the production of hydroxyl radicals both at the surface of the non-active Ti4O7 electrode and in solution by the electro-Fenton process at the cathodic carbon felt. Complete removal of tetracycline was observed from HPLC data after 30 min at optimized conditions of 120 mA and 210 mA for 20 ppm and 50 ppm tetracycline concentrations. Degradation products were elucidated, and the toxicity of the products were measured with luminescence using Microtox® bacteria toxicity test. [ABSTRACT FROM AUTHOR]

Photocatalytic water splitting into hydrogen is considered as one of the key solutions to the current demand for eco-responsible energy. To improve the efficiency and sustainability of this process, the development of a TiO2-based photoanode by adding bio-sourced surfactants to the sol–gel preparation method has been considered. Three different polymeric biosurfactants (GB, GC, and BIO) have been tested, giving rise to three different materials being structurally and morphologically characterized by XRD, Rietveld refinement, BET, SEM, AFM, and XPS, which was completed by light absorption, photocatalytic (Pilkington test), electronic (EIS and C-AFM), and photoelectrochemical (cyclic voltammetry) measurements. Correlations between the structure/morphology of materials and their functional properties have been established. One specific surfactant has been proven as the most suitable to lead to materials with optimized photoelectrochemical performance in direct relation with their photocatalytic properties essentially controlled by their specific surface area. [ABSTRACT FROM AUTHOR]

The bactericidal activity of an Al2O3-TiO2-Ag granular material against an Escherichia coli strain was confirmed by a culture-based method. In particular, 100% of microorganisms were permanently inactivated in 30 to 45 min. The present work aimed to investigate the mechanisms of the bactericidal action of this material and their dynamics on Escherichia coli using different techniques. Observations by transmission electron microscopy (TEM) at different times of disinfection revealed morphological changes in the bacteria as soon as they were put in contact with the material. Notably highlighted were cell membrane damage; cytoplasm detachment; formation of vacuoles, possibly due to DNA condensation, in association with regions exhibiting different levels of electron density; and membrane lysis. PCR and flow cytometry analyses were used to confirm and quantify the observations of cell integrity. The direct exposure of cells to silver, combined with the oxidative stress induced by the reactive oxygen species (ROS) generated, was identified to be responsible for these morphological alterations. From the first 5 min of treatment with the Al2O3-TiO2-Ag material, 98% of E. coli isolates were lysed. From 30 min, cell viability decreased to reach total inactivation, although approximately 1% of permeable E. coli cells and 1% of intact cells (105 genomic units · ml-1) were evidenced. This study demonstrates that the bactericidal effect of the material results from a synergic action of desorbed and supported silver. Supported silver was shown to generate the ROS evidenced. [ABSTRACT FROM AUTHOR]

Metal oxides and metal oxide/carbon composites are entering the development of new technologies and should therefore to be prepared by sustainable chemistry processes. Therefore, a new aspect of the reactivity of cellulose is presented through its solid/gas reaction with vapour of titanium(IV) chloride in anhydrous conditions at low temperature (80 °C). This reaction leads to two transformations both for cellulose and titanium(IV) chloride. A reductive dehydration of cellulose is seen at the lowest temperature ever reported and results in the formation of a carbonaceous fibrous solid as the only carbon-containing product. Simultaneously, the in situ generation of water leads to the formation of titanium dioxide with an unexpected nanoplate morphology (ca. 50 nm thickness) and a high photocatalytic activity. We present the evidence showing the evolution of the cellulose and the TiO 2 nanostructure formation, along with its photocatalytic activity. This low-temperature process avoids any other reagents and is among the greenest processes for the preparation of anatase and also for TiO 2 /carbon composites. The anisotropic morphology of TiO 2 questions the role of the cellulose on the growing process of these nanoparticles., (© 2016 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.)

The bactericidal activity of an Al2O3-TiO2-Ag granular material against an Escherichia coli strain was confirmed by a culture-based method. In particular, 100% of microorganisms were permanently inactivated in 30 to 45 min. The present work aimed to investigate the mechanisms of the bactericidal action of this material and their dynamics on Escherichia coli using different techniques. Observations by transmission electron microscopy (TEM) at different times of disinfection revealed morphological changes in the bacteria as soon as they were put in contact with the material. Notably highlighted were cell membrane damage; cytoplasm detachment; formation of vacuoles, possibly due to DNA condensation, in association with regions exhibiting different levels of electron density; and membrane lysis. PCR and flow cytometry analyses were used to confirm and quantify the observations of cell integrity. The direct exposure of cells to silver, combined with the oxidative stress induced by the reactive oxygen species (ROS) generated, was identified to be responsible for these morphological alterations. From the first 5 min of treatment with the Al2O3-TiO2-Ag material, 98% of E. coli isolates were lysed. From 30 min, cell viability decreased to reach total inactivation, although approximately 1% of permeable E. coli cells and 1% of intact cells (10(5) genomic units·ml(-1)) were evidenced. This study demonstrates that the bactericidal effect of the material results from a synergic action of desorbed and supported silver. Supported silver was shown to generate the ROS evidenced., (Copyright © 2015, American Society for Microbiology. All Rights Reserved.)