Search

Purpose: To evaluate the performance of fixed complete dental prostheses supported by axial and tilted implants after at least 3 years of follow-up. Materials and Methods: An electronic search plus a hand search up to April 2021 was undertaken. Clinical studies were selected using specific inclusion criteria, independent of the study design. The main outcomes were cumulative implant survival rate, marginal bone level changes, and complications, after ≥ 3 years of follow-up. The difference in outcomes between axial and tilted implants and between the maxilla and mandible was evaluated using meta-analysis and the Mantel-Cox test. Results: Out of 824 articles retrieved, 24 were included. In total, 2,637 patients were rehabilitated with 2,735 full prostheses (1,464 maxillary, 1,271 mandibular), supported by 5,594 and 5,611 tilted and axial implants, respectively. In a range between 3 and 18 years of follow-up, 274 implants failed. The cumulative implant survival rate was 93.91% and 99.31% for implants and prostheses, respectively. The mean marginal bone level change was moderate, exceeding 2 mm in only two studies. Marginal bone loss was significantly lower around axial compared with tilted implants (P < .0001), whereas it was not affected by arch (maxilla vs mandible; P = .17). Conclusion: Fixed complete dental prostheses supported by tilted and axially placed implants represent a predictable option for the rehabilitation of edentulous arches. Further randomized trials are needed to determine the efficacy of this surgical approach and the remodeling pattern of marginal bone in the long term. [ABSTRACT FROM AUTHOR]

Purpose: The aim of this in vitro study was to measure the insertion and removal torque values of dental implant replicas inserted into artificial bone blocks using different surgical burs and drilling protocols. Materials and methods: Four types of artificial, polyurethane bone blocks were used with different thicknesses (1 and 2 mm) and densities (soft‐1 mm, soft‐2 mm, dense‐1 mm, and dense‐2 mm) of the simulated cortical and cancellous bone, respectively. Each bone construct was drilled with Straumann and Densah drills in both clockwise and counterclockwise directions for a total of 16 experimental conditions. For every scenario, 38 implant replicas were inserted and then removed after 1 min. Outcomes of interest were the insertion and removal torque values which were recorded by a torque meter. ANOVA and Tukey HSD tests were used to assess differences across each combination of drill, direction, and bone type. Results: Densah counterclockwise registered statistically greater values for both insertion and removal torque, followed by Densah clockwise, Straumann counterclockwise, and Straumann clockwise. Increasing insertion and removal torque values were progressively reported for bone type (soft‐1 mm, dense‐1 mm, soft‐2 mm, and dense‐2 mm). The mean values of insertion and removal torque were significantly different (p < 0.05) across the four bone types, different burs, and with the two drilling modalities. Conclusions: Densah bur resulted in significantly greater values of torque compared to the Straumann drills for all the experimental conditions. The thickness of the cortical layer and the counterclockwise drilling direction play a significant role in determining the implant insertion torque. [ABSTRACT FROM AUTHOR]

Purpose: To determine the survival rate, incidence of prosthetic complications, and patient satisfaction of implant fixed complete dental prostheses (IFCDPs) after a mean observation period of 1.4 years. Materials and methods: Twenty‐eight (28) eligible participants were recruited according to specific inclusion and exclusion criteria. The definitive metal‐acrylic resin IFCDPs consisted of titanium bars veneered with acrylic resin and acrylic denture teeth. Prosthodontic complications, divided into major and minor, were monitored. Parameters such as gender, jaw location, bruxism, and occlusal scheme were evaluated. Moreover, a questionnaire was administered throughout the study to assess patient satisfaction. Poisson regression as well as repeated measures ANOVA were used for statistical analysis. Results: Fourteen (14) males and 14 females were enrolled and followed‐up at 3, 6, and 12 months. All IFCDPs survived (100% survival rate). The most frequent minor complication was the loss of material used to close the screw access hole (20% out of total complications). The most frequent major complication was chipping of the acrylic denture teeth (77.14% out of total complications). Gender (p = 0.008) and bruxism (p = 0.030) were significant predictors for the total major complications (major wear and major chipping) while occlusal scheme was a significant predictor for major chipping events (p = 0.030). Conclusions: While IFCDPs demonstrated high prosthetic survival rates, they also exhibited a high number of chipping events of the acrylic veneering material, especially in males, bruxers, and individuals with canine guidance occlusion. However, the occurrence of these prosthetic complications did not negatively affect patient satisfaction. [ABSTRACT FROM AUTHOR]

Purpose: Microgaps at the implant-abutment interface allow for microbial colonization, which can lead to peri-implant tissue inflammation. This study sought to determine the marginal accuracy of three different implant.zirconium oxide (zirconia) abutment configurations and one implant.titanium abutment configuration. Materials and Methods: Three combinations of implants with custom-made zirconia abutments were analyzed (n = 5/group): NobelProcera abutments/titanium inserts on Replace Select Tapered TiUnite implants (Nobel Biocare) (NP); Encode abutments/NanoTite Tapered Certain implants (Biomet 3i) (B3i); Astra Tech Dental Atlantis abutments/Biomet 3i NanoTite Tapered Certain implants (At). Five custom-made Encode titanium abutments/NanoTite Tapered Certain implants (Ti) were used as a control group. All abutments were fabricated with computer-aided design/computer-assisted manufacture. One-hundred twenty vertical gap measurements were made per sample using scanning electron microscopy (15 scans × 4 aspects of each specimen [buccal, mesial, palatal, distal] × 2 measurements). Analysis of variance was used to compare the marginal fit values among the four groups, the specimens within each group, and the four aspects of each specimen. Results: Mean (± standard deviation) gap values were 8.4 ± 5.6 µm (NP), 5.7 } 1.9 µm (B3i), 11.8 ± 2.6 µm (At), and 1.6 ± 0.5 µm (Ti). A significant difference was found between B3i and At. No difference resulted between NP with the other two groups. Gap values were significantly smaller for Ti relative to all zirconia systems. For each ceramic abutment configuration, the fit was significantly different among the five specimens. For 12 of the 15 ceramic abutment specimens, gap values sorted by aspect were significantly different. Conclusions: The implant.titanium abutment connection showed significantly better fit than all implant.zirconia abutment configurations, which demonstrated mean gaps that were approximately three to seven times larger than those in the titanium abutment system. [ABSTRACT FROM AUTHOR]

Purpose: This article reports preliminary results of a single-cohort prospective study that sought to evaluate a new surgical protocol for the immediate rehabilitation of edentulous maxilla without using bone grafting. Materials and Methods: Twenty consecutive patients in need of a full-arch maxillary rehabilitation were included in the study. Each patient received four tilted implants that engaged the posterior and the anterior sinus wall and two axial implants in the anterior maxilla. A total of 120 implants (30 Brånemark System MK IV and 90 NobelSpeedy Groovy) was inserted. Acrylic resin provisional prostheses were delivered within 4 hours of implant placement, and definitive restorations were placed 4 to 6 months later. Follow-up visits were scheduled every 6 months for the first 2 years and yearly thereafter. At each follow-up appointment, plaque and bleeding indexes were scored, periapical radiographs were obtained to assess marginal bone level changes, and patient satisfaction was recorded by means of a questionnaire. Results: The follow-up ranged between 18 and 42 months (average, 27.2 months). No implants failed. All prostheses were stable and functional. No adverse events occurred. At 1 year, mean marginal bone loss around axial and tilted implants was similar: 0.8 mm for axial implants (SD 0.4, n = 30) and 0.9 mm for tilted implants (SD 0.5 mm, n = 60) (P > .05). Plaque and bleeding scores decreased over time, and patient satisfaction with both esthetics and function increased. Conclusions: This technique can be considered a viable treatment modality for the immediate rehabilitation of the edentulous maxilla, as it provides optimal support in the posterior region, minimizes distal cantilevers, and avoids bone grafting or sinus augmentation. [ABSTRACT FROM AUTHOR]

Purpose: The purpose of the study was to evaluate, using finite element analysis, the stress patterns induced in cortical bone by three distinct implant-supported prosthetic designs. Materials and Methods: The first two models consisted of a prosthesis supported by four implants, the distal two of which were tilted, with different cantilever lengths (5 mm and 15 mm). The third design consisted of a prosthesis supported by five conventionally placed implants and a 15-mm cantilever. Results: In the tilted model with 5-mm cantilever and in the nontilted model, the maximum value of compressive stress (-18 MPa) was found near the cervical area of the distal implant. Higher values for compressive stress were predicted near the cervical area of the distal implant in the tilted model with a 15-mm cantilever, as compared to the tilted model with the 5-mm cantilever. For the tilted model with the 5-mm cantilever, peak values of tensile stress were predicted near the cervical area of both the distal (1.25 MPa) and the mesial implants (2.5 MPa). For the nontilted model, the peak value was found near the cervical area of the in-between implant (5 MPa). For the tilted model with 15-mm cantilever, tensile stress values were higher than in the tilted model with 5-mm cantilever. Conclusions: No significant difference in stress patterns between the tilted 5-mm and the nontilted 15-mm configuration was predicted. The tilted configuration with a 15-mm cantilever was found to induce higher stress values than the tilted configuration with a 5-mm cantilever. [ABSTRACT FROM AUTHOR]

The aim of this study was to evaluate stress patterns at the bone-implant interface of tilted versus nontilted implant configurations in edentulous maxillae using finite element models of two tilted and one nontilted configuration. Analysis predicted the maximum absolute value of principal compressive stress near the cervical area of the distal implant for all models. The tilted configurations showed a lower absolute value of compressive stress compared with the nontilted, indicating a possible biomechanical advantage in reducing stresses at the bone-implant interface. [ABSTRACT FROM AUTHOR]

During intraoral complete-arch digital implant scanning, one of the most technique-sensitive steps is the implant data acquisition and merging of different surface geometry data sets for prototype prosthesis fabrication due to the absence of fixed landmarks. Recently developed extraoral techniques have allowed for an alternative approach for the digital acquisition of implant position in completely edentulous patients. Specifically, extraoral digital scanning of the conversion prosthesis after connecting reverse scan bodies has been proposed as an efficient approach. The reverse scan body protocol digitally simulates the traditional back-pouring technique long utilized in analog workflows. The present article describes a technique for simplifying the digital workflow for the fabrication of passive-fitting definitive prostheses using the reverse scan body concept., (© 2024 by the American College of Prosthodontists.)