Search

X-ray phase contrast imaging (XPCI) provides higher sensitivity to contrast between low absorbing objects that can be invisible to conventional attenuation-based X-ray imaging. XPCI's main application has been so far focused on medical areas at relatively low energies (< 100 keV). The translation to higher energy for industrial applications, where energies above 150 keV are often needed, is hindered by the lack of masks/gratings with sufficiently thick gold septa. Fabricating such structures with apertures of tens of micrometers becomes difficult at depths greater than a few hundreds of micrometers due to aspect ratio dependent effects such as anisotropic etching, and preferential gold (Au) deposition at the top of the apertures. In this work, these difficulties are overcome by Deep Reactive Ion Etching optimized by a stepped parameters approach and bismuth-mediated superconformal filling of Au, ultimately resulting in 500 micrometers deep silicon masks filled with Au at bulk density. The obtained masks, tested in an Edge Illumination XPCI system with a conventional source and a photon-counting detector, show good agreement with simulations at different energy thresholds. They also demonstrate a higher phase sensitivity for highly absorbing objects when compared to lower aspect ratio masks, proving their potential for industrial non-destructive testing., Comment: 6 figure plus table of content at the end

Semiconductor integrated circuits operated at cryogenic temperature will play an essential role in quantum computing architectures. These can offer equivalent or superior performance to their room-temperature counterparts while enabling a scaling up of the total number of qubits under control. Silicon integrated circuits can be operated at a temperature stage of a cryogenic system where cooling power is sufficient ($\sim$3.5+ K) to allow for analog signal chain components (e.g. amplifiers and mixers), local signal synthesis, signal digitization, and control logic. A critical stage in cryo-electronics development is the characterization of individual transistor devices in a particular technology node at cryogenic temperatures. This data enables the creation of a process design kit (PDK) to model devices and simulate integrated circuits operating well below the minimum standard temperature ranges covered by foundry-released models (e.g. -55 {\deg}C). Here, an efficient approach to the characterization of large numbers of components at cryogenic temperature is reported. We developed a system to perform DC measurements with Kelvin sense of individual transistors at 4.2 K using integrated on-die multiplexers, enabling bulk characterization of thousands of devices with no physical change to the measurement setup., Comment: 9 pages, 4 figures

In 2022 the DART mission spacecraft impacted the asteroid Dimorphos, the secondary body of the binary Didymos system, ejecting a large number of dust particles, rocks and boulders. The ESA Hera mission will reach the system in 2026 for post--impact studies and possible detection of orbiting fragments. We investigate the long term dynamics of the large boulders ejected by DART to test if any of these objects survive in orbit until the arrival of the Hera mission. To model the dynamics of the boulders we use a numerical model which includes the gravity of non-spherical Didymos and Dimorphos, the solar gravity and the radiation pressure. The SPICE kernels are used to define the correct reference frame for the integration. The dynamics of the boulders is highly chaotic and 1% of the initial boulders survive at least for 4 years on quasi--stable orbits. These orbits are characterised by wide oscillations in eccentricity in antiphase with those in inclination (including spin flips), a mechanism similar to the Kozai one. This behaviour may protect these bodies from close encounters with both asteroids. We also compute the distribution on the surfaces of the asteroids of sesquinary impacts which may influence the dust emission, after the initial DART impact, and the surface composition of the asteroids. The probability of observing boulders by the mission Hera is small but not negligible and an almost constant flux of escaping boulders is expected in the coming years since their lifetime after the DART impact covers a large time interval. Most of re--impacts on Dimorphos occur in the hemisphere opposite to the impact site, preferentially close to the equatorial plane., Comment: Accepted in A&A

The NASA/DART (Double Asteroid Redirection Test) spacecraft successfully crashed on Dimorphos, the secondary component of the binary (65803) Didymos system. Following the impact, a large dust cloud was released, and a long-lasting dust tail was developed. We have extensively monitored the dust tail from the ground and from the Hubble Space Telescope (HST). We provide a characterization of the ejecta dust properties, i.e., particle size distribution and ejection speeds, ejection geometric parameters, and mass, by combining both observational data sets, and by using Monte Carlo models of the observed dust tail. The differential size distribution function that best fits the imaging data was a broken power-law, having a power index of --2.5 for particles of r$\le$ 3 mm, and of --3.7 for larger particles. The particles range in sizes from 1 $\mu$m up to 5 cm. The ejecta is characterized by two components, depending on velocity and ejection direction. The northern component of the double tail, observed since October 8th 2022, might be associated to a secondary ejection event from impacting debris on Didymos, although it is also possible that this feature results from the binary system dynamics alone. The lower limit to the total dust mass ejected is estimated at $\sim$6$\times$10$^6$ kg, half of this mass being ejected to interplanetary space., Comment: Accepted by Planetary Science Journal, July 7th, 2023

The NASA Double Asteroid Redirection Test (DART) mission performed a kinetic impact on asteroid Dimorphos, the satellite of the binary asteroid (65803) Didymos, at 23:14 UTC on September 26, 2022 as a planetary defense test. DART was the first hypervelocity impact experiment on an asteroid at size and velocity scales relevant to planetary defense, intended to validate kinetic impact as a means of asteroid deflection. Here we report the first determination of the momentum transferred to an asteroid by kinetic impact. Based on the change in the binary orbit period, we find an instantaneous reduction in Dimorphos's along-track orbital velocity component of 2.70 +/- 0.10 mm/s, indicating enhanced momentum transfer due to recoil from ejecta streams produced by the impact. For a Dimorphos bulk density range of 1,500 to 3,300 kg/m$^3$, we find that the expected value of the momentum enhancement factor, $\beta$, ranges between 2.2 and 4.9, depending on the mass of Dimorphos. If Dimorphos and Didymos are assumed to have equal densities of 2,400 kg/m$^3$, $\beta$= 3.61 +0.19/-0.25 (1 $\sigma$). These $\beta$ values indicate that significantly more momentum was transferred to Dimorphos from the escaping impact ejecta than was incident with DART. Therefore, the DART kinetic impact was highly effective in deflecting the asteroid Dimorphos., Comment: accepted by Nature

Some active asteroids have been proposed to be the result of impact events. Because active asteroids are generally discovered serendipitously only after their tail formation, the process of the impact ejecta evolving into a tail has never been directly observed. NASA's Double Asteroid Redirection Test (DART) mission, apart from having successfully changed the orbital period of Dimorphos, demonstrated the activation process of an asteroid from an impact under precisely known impact conditions. Here we report the observations of the DART impact ejecta with the Hubble Space Telescope (HST) from impact time T+15 minutes to T+18.5 days at spatial resolutions of ~2.1 km per pixel. Our observations reveal a complex evolution of ejecta, which is first dominated by the gravitational interaction between the Didymos binary system and the ejected dust and later by solar radiation pressure. The lowest-speed ejecta dispersed via a sustained tail that displayed a consistent morphology with previously observed asteroid tails thought to be produced by impact. The ejecta evolution following DART's controlled impact experiment thus provides a framework for understanding the fundamental mechanisms acting on asteroids disrupted by natural impact., Comment: accepted by Nature

Diffractive optical elements such as periodic gratings are fundamental devices in X-ray imaging - a technique that medical, material science and security scans rely upon. Fabrication of such structures with high aspect ratios at the nanoscale creates opportunities to further advance such applications, especially in terms of relaxing X-ray source coherence requirements. This is because typical grating-based X-ray phase imaging techniques (e.g., Talbot self-imaging) require a coherence length of at least one grating period and ideally longer. In this paper, the fabrication challenges in achieving high aspect-ratio nanogratings filled with gold are addressed by a combination of laser interference and nanoimprint lithography, physical vapor deposition, metal assisted chemical etching (MACE), and electroplating. This relatively simple and cost-efficient approach is unlocked by an innovative post-MACE drying step with hexamethyldisilazane, which effectively minimizes the stiction of the nanostructures. The theoretical limits of the approach are discussed and, experimentally, X-ray nanogratings with aspect ratios >40 demonstrated. Finally, their excellent diffractive abilities are shown when exposed to a hard (12.2 keV) monochromatic x-ray beam at a synchrotron facility, and thus potential applicability in phase-based X-ray imaging., Comment: 27 pages, 5 figures in main text, plus supporting information

NASA's Double Asteroid Redirection Test (DART) is the first full-scale test of an asteroid deflection technology. Results from the hypervelocity kinetic impact and Earth-based observations, coupled with LICIACube and the later Hera mission, will result in measurement of the momentum transfer efficiency accurate to ~10% and characterization of the Didymos binary system. But DART is a single experiment; how could these results be used in a future planetary defense necessity involving a different asteroid? We examine what aspects of Dimorphos's response to kinetic impact will be constrained by DART results; how these constraints will help refine knowledge of the physical properties of asteroidal materials and predictive power of impact simulations; what information about a potential Earth impactor could be acquired before a deflection effort; and how design of a deflection mission should be informed by this understanding. We generalize the momentum enhancement factor $\beta$, showing that a particular direction-specific $\beta$ will be directly determined by the DART results, and that a related direction-specific $\beta$ is a figure of merit for a kinetic impact mission. The DART $\beta$ determination constrains the ejecta momentum vector, which, with hydrodynamic simulations, constrains the physical properties of Dimorphos's near-surface. In a hypothetical planetary defense exigency, extrapolating these constraints to a newly discovered asteroid will require Earth-based observations and benefit from in-situ reconnaissance. We show representative predictions for momentum transfer based on different levels of reconnaissance and discuss strategic targeting to optimize the deflection and reduce the risk of a counterproductive deflection in the wrong direction., Comment: 30 pages, 7 figures. Planetary Science Journal, in press, accepted 2022 September 22

NASA's Double Asteroid Redirection Test (DART) spacecraft is planned to impact the natural satellite of (65803) Didymos, Dimorphos, around 23:14 UTC on 26 September 2022, causing a reduction in its orbital period that will be measurable with ground-based observations. This test of kinetic impactor technology will provide the first estimate of the momentum transfer enhancement factor $\beta$ at a realistic scale, wherein ejecta from the impact provides an additional deflection to the target. Earth-based observations, the LICIACube spacecraft (to be detached from DART prior to impact), and ESA's follow-up Hera mission to launch in 2024, will provide additional characterization of the deflection test. Together Hera and DART comprise the Asteroid Impact and Deflection Assessment (AIDA) cooperation between NASA and ESA. Here the predicted dynamical states of the binary system upon arrival and after impact are presented. The assumed dynamically relaxed state of the system will be excited by the impact, leading to an increase in eccentricity and slight tilt of the orbit together with enhanced libration of Dimorphos with amplitude dependent on the currently poorly known target shape. Free rotation around the moon's long axis may also be triggered and the orbital period will experience variations from seconds to minutes over timescales of days to months. Shape change of either body due to cratering or mass wasting triggered by crater formation and ejecta may affect $\beta$ but can be constrained through additional measurements. Both BYORP and gravity tides may cause measurable orbital changes on the timescale of Hera's rendezvous., Comment: 23 pages, 13 figures, published in PSJ

The rapid progress of hole spin qubits in group IV semiconductors has been driven by their potential for scalability. This is owed to the compatibility with industrial manufacturing standards, as well as the ease of operation and addressability via all-electric drives. However, owing to a strong spin-orbit interaction, these systems present variability and anisotropy in key qubit control parameters such as the Land\'e $g-$factor, requiring careful characterisation for reliable qubit operation. Here, we experimentally investigate a hole double quantum dot in silicon by carrying out spin readout with gate-based reflectometry. We show that characteristic features in the reflected phase signal arising from magneto-spectroscopy convey information on site-dependent $g-$factors in the two dots. Using analytical modeling, we extract the physical parameters of our system and, through numerical calculations, we extend the results to point out the prospect of conveniently extracting information about the local $g-$factors from reflectometry measurements., Comment: Main manuscript: 12 pages, 8 figures. Supplementary Information: 3 pages, 2 figures

Any population of asteroids, like asteroid families, will disperse in semi-major axis due to the Yarkovsky effect. The amount of drift is modulated by the asteroid spin state evolution which determines the balance between the diurnal and seasonal Yarkovsky force. The asteroid's spin state is, in turn, controlled in part by the YORP effect. The otherwise smooth evolution of an asteroid can be abruptly altered by collisions, which can cause impulsive changes in the spin state and can move the asteroid onto a different YORP track. In addition, collisions may also alter the YORP parameters by changing the superficial features and overall shape of the asteroid. Thus, the coupling between YORP and Yarkovsky is also strongly affected by the impact history of each body. To investigate this coupling we developed a statistical code modeling the time evolution of semi--major axis under YORP-Yarkovsky coupling. It includes the contributions of NYORP (normal YORP), TYORP (tangential YORP) and collisions whose effects are deterministically calculated and not added in a statistical way. We find that both collisions and TYORP increase the dispersion of a family in semi-major axis by making the spin axis evolution less smooth and regular. We show that the evolution of a family's structure with time is complex and collisions randomize the YORP evolution. In our test families we do not observe the formation of a 'YORP-eye' in the semi-major axis vs. diameter distribution, even after a long period of time. If present, the 'YORP-eye' might be a relic of an initial ejection velocity pattern of the collisional fragments.

Hydrogenated amorphous silicon (a-Si:H) has remarkable radiation resistance properties and can be deposited on a lot of different substrates. A-Si:H based particle detectors have been built since mid 1980s as planar p-i-n or Schottky diode structures; the thickness of these detectors ranged from 1 to 50 micron. However MIP detection using planar structures has always been problematic due to the poor S/N ratio related to the high leakage current at high depletion voltage and the low charge collection efficiency. The usage of 3D detector architecture can be beneficial for the possibility to reduce inter-electrode distance and increase the thickness of the detector for larger charge generation compared to planar structures. Such a detector can be used for future hadron colliders for its radiation resistance and also for X-ray imaging. Furthermore the possibility of a-Si:H deposition on flexible materials (like kapton) can be exploited to build flexible and thin beam flux measurement detectors and x-ray dosimeters., Comment: 10 pages 5 figures, 1 table

While theories postulating a dual cognitive system take hold, quantitative confirmations are still needed to understand and identify interactions between the two systems or conflict events. Eye movements are among the most direct markers of the individual attentive load and may serve as an important proxy of information. In this work we propose a computational method, within a modified visual version of the well-known Stroop test, for the identification of different tasks and potential conflicts events between the two systems through the collection and processing of data related to eye movements. A statistical analysis shows that the selected variables can characterize the variation of attentive load within different scenarios. Moreover, we show that Machine Learning techniques allow to distinguish between different tasks with a good classification accuracy and to investigate more in depth the gaze dynamics., Comment: 11 pages, 2 figures, 1 tables