Search

A multifunctional modified layer (DPPTPTA@CuCoP/CNF) was used for the first time in dye-sensitized solar cells, which achieved a conversion efficiency of 25.44 at 6000 lux and ensured long-term stability (90% retention after 3000 h).

In this paper we describe three indacenodithiophene-based conjugated polymers (PITIC-Ph, PITIC-Th, and PITIC-ThF) that we tested as third components for PM6:Y6-based ternary organic photovoltaics (OPVs) to provide high-power conversion efficiencies (PCEs) and long-term thermal stabilities. Among them, the incorporation of PITIC-Ph enhanced the charge dissociation and prohibited the bimolecular (trap-assisted) recombination of the PM6:Y6 blend. Compared with the pre-optimized OPV device, the PCEs of the PITIC-Ph-doped devices improved from 15.0 ± 0.37 to 17.0 ± 0.35% under AM 1.5 G (100 mW cm−2) irradiation. More critically, studies of the thermal stability revealed another phenomenon: embedding PITIC-Ph decreased the degree of thermally driven phase segregation of the PM6:Y6 blend film. The respective OPVs exhibited outstanding thermal stability under stress at 150 °C within a glove box, with the PCE of the PITIC-Ph-doped device remaining high (at 16.4%) after annealing for 560 h.

In this study, we designed a surface phase-matched transmission enhancement top electrode-Ag/indium tin oxide (ITO) structure for highly efficient and aesthetic semitransparent organic photovoltaics (ST-OPVs). The purposed highly transparent back electrodes (Ag/ITO) could selectively decrease visible reflection and increase transparency accordingly. By altering the thicknesses of the Ag and ITO layers, we could control the transmittance curve and increase the transparency of the ST-OPV devices. Devices based on PTB7-Th:IEICO-4F and PM6:Y6:PC71BM displayed outstanding performance (8.1 and 10.2%, respectively) with high photopic-weighted visible light transmittance (36.2 and 28.6%, respectively). The outstanding visible and near-infrared light harvesting of PM6:Y6:PC71BM further allowed a new application: double-sided energy harvesting from solar and indoor illumination. The simple optical design of a top electrode displaying high transparency/conductivity has a wide range of potential applications in, for example, greenhouse photovoltaics, tandem cells, and portable devices.

An acceptor-donor-acceptor (A-D-A)-type non-fullerene acceptor (NFA), PTTtID-Cl, featuring thieno[3,2-b]thieno[2''',3''':4'',5'']-pyrrolo[2'',3'':4',5']thieno[2',3':4,5]thieno-[2,3-d]pyrrole (DTPTt) as the electron-rich core and 2-(5,6-dichloro-3-oxo-2,3-dihydro-1H-inden-1-ylidene)malononitrile (ID-Cl) as the peripheral electron-deficient terminal group was synthesized and characterized. PTTtID-Cl exhibited strong absorption in the range of 700-850 nm in CHCl3 and redshifted absorption centered at 881 nm in a thin film. The near infrared (NIR)-absorption of PTTtID-Cl was combined with a low-bandgap polymer donor (PTB7-Th) to achieve binary and semitransparent organic photovoltaics (OPVs) with a power conversion efficiency (PCE) of 8.9 % and 7.7 % (with an average visible transmittance (AVT) of 16.7 %), respectively. A ternary device with a ratio of PM7/PTTtID-Cl/IT-4F=1:0.15:0.85 (w/w) achieved a short-circuit current density of 19.46 mA cm-2 , an open-circuit voltage of 0.87 V, and a fill factor of 71.2 %, giving a PCE of 12.0 %. In addition, by employing the Ag/ITO/Ag microcavity structure, semitransparent colorful binary organic photovoltaics (OPVs) with superior transparency of 27.9 % at 427 nm and 22.7 % at 536 nm for blue and green devices, respectively, were prepared. The semitransparent colorful devices based on the optimized ternary blend gave PCEs of 8.7 %, 8.4 %, and 9.1 % for blue, green, and red devices, respectively. These results indicate the promising potential of PTTtID-Cl as a NIR-absorption NFA for applications in semitransparent colorful binary and ternary OPVs.

In this study, the core-shell of Fe

In this study, a series of crosslinked membranes were prepared as solid polymer electrolytes (SPEs) for all-solid-state lithium ion batteries (ASSLIBs). An epoxy-containing copolymer (glycidyl methacrylate-co-poly(ethylene glycol) methyl ether methacrylate, PGA) and two amine curing agents, linear Jeffamine ED2003 and hyperbranched polyethyleneimine (PEI), were utilized to prepare SPEs with various crosslinking degrees. The PGA/polyethylene oxide (PEO) blends were cured by ED2003 and PEI to obtain slightly and heavily crosslinked structures, respectively. For further optimizing the interfacial and the electrochemical properties, an interlocking bilayer membrane based on overlapping and subsequent curing of PGA/PEO/ED2003 and PEO/PEI layers was developed. The presence of this amino/epoxy network can inhibit PEO crystallinity and maintain the dimensional stability of membranes. For the slightly crosslinked PGA/PEO/ED2003 membrane, an ionic conductivity of 5.61 × 10−4 S cm−1 and a lithium ion transference number (tLi+) of 0.43 were obtained, along with a specific capacity of 156 mAh g−1 (0.05 C) acquired from an assembled half-cell battery. However, the capacity retention retained only 54% after 100 cycles (0.2 C, 80 °C), possibly because the PEO-based electrolyte was inclined to recrystallize after long term thermal treatment. On the other hand, the highly crosslinked PGA/PEO/PEI membrane exhibited a similar ionic conductivity of 3.44 × 10−4 S cm−1 and a tLi+ of 0.52. Yet, poor interfacial adhesion between the membrane and the cathode brought about a low specific capacity of 48 mAh g−1. For the reinforced interlocking bilayer membrane, an ionic conductivity of 3.24 × 10−4 S cm−1 and a tLi+ of 0.42 could be achieved. Moreover, the capacity retention reached as high as 80% after 100 cycles (0.2 C, 80 °C). This is because the presence of the epoxy-based interlocking bilayer structure can block the pathway of lithium dendrite puncture effectively. We demonstrate that the unique interlocking bilayer structure is capable of offering a new approach to fabricate a robust SPE for ASSLIBs.

Conjugated polyelectrolytes (CPEs) have developed as promising hole transport materials for perovskite solar cells (PSCs). The conjugated backbone serves as an efficient vehicle for transporting holes, and the electric dipole layer formed through the organization of ionic groups on CPEs may improve the hole collection efficiency. In this work, three CPEs anchored with –N(CH3)3+, –SO3− and –NH3+ ions, denoted as BF-NMe3, BF-SO3 and BF-NH3, respectively, were synthesized and applied as the hole transport material (HTM) of inverted planar PSCs. Replacing the benchmark material, poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS), with the three CPEs as the HTM considerably improves the photovoltaic performance of PSCs. The results from scanning electron microscope imaging, X-ray diffraction and time-resolved photoluminescence indicate that the structure of the ionic species rather than the type of charge has a decisive impact on the perovskite morphology. Both cationic BF-NH3 and anionic BF-SO3 layers enable methylammonium lead iodide (MAPbI3) to grow into larger crystals and grains with fewer defects. Moreover, the electrochemical impedance spectroscopy measurements demonstrate that the BF-NH3 and BF-SO3 devices have comparable charge recombination resistance, which is apparently higher than that of the BF-NMe3 and PEDOT:PSS devices. Consequently, the cationic BF-NH3 can act as an excellent HTM as the anionic BF-SO3 and the champion cell based on BF-NH3 exhibits a superior power conversion efficiency of 17.7%.

A series of new metal-free organic dyes based on 3,3′-dithioalkyl-2,2′-bithiophene (SBT) organic chromophores was synthesized for use in dye-sensitized solar cells (DSSCs). Because S(alkyl)⋯S(thiophene) intermolecular interlocking renders the twist angle in the structure as

Nowadays, chronic kidney disease (CKD) becomes a principal barrier in clinical diagnosis and treatment. For clinical patients, chronic kidney disease will potentially lead to multiple lesion that increase the risk of mortality. The most significant challenge in CKD is detecting uremic toxins, including small water-soluble solutes (uric acid, urea and creatinine) and protein-bound solutes (p-cresol and indoxyl sulfate). Surface-enhanced Raman scattering (SERS) platform is rapid and sensitive nanotechnology for bio-detection. Thus, the floating-typed SERS substrate is prepared by embedded silver nanoparticles (AgNPs) on the poly (diallyldimethyl-ammonium) chloride (PDDA) modified graphene oxide (GO) nanosheets for the biomolecules and uremic toxins detection. The optimal interparticle distances of AgNPs are modulated to generate the strong “hot spots” for enhancing Raman signals. The characterizations of AgNPs/GO-PDDA nanosheets are evaluated by transmission electron microscopy, zeta potential, FTIR, X-ray photoelectron spectroscopy, and Raman spectroscopy. The results show that the floating SERS-active substrate provides quantitatively linear measurement (i.e., 3.8 × 10−2 ˜10-5 M of urea) and ultrasensitive SERS detection (i.e., detection limit of adenine: lower than 10-10 M) of biomolecules, which offers great potential for practical clinical applications in rapid and label-free detection of clinical uremic toxins.

Arrays of 20 nm silver nanoparticles (AgNPs) with tunable interparticle gaps have been grown on mesoporous silica (MPS) nanospheres to form AgNPs@MPS nanohybrids for surface-enhanced Raman scatteri...

In this study, a transition-metal selenide, vanadium diselenide (VSe2), with various morphologies was synthesized by employing a surfactant-free hydrothermal method under varied temperature conditi...

We have successfully prepared a floating-typed surface-enhanced Raman scattering (SERS) substrate by the uniform nanoparticle arrays of silver nanoparticles (AgNPs) immobilized on the dendron-exfoliated reduced graphene oxide (rGO) nanosheets. These poly(urea/malonamide) dendrons were precisely synthesized, and then grafted on the dendron-exfoliated rGO nanosheets based on an efficient building block of dual functional 4-isocyanato-4′-(3,3-dimethyl-2,4-dioxo-azetidino)-diphenylmethane (IDD). By using dendron-rGO nanosheets as templates for hosting AgNPs, the particle size (D) and interparticle gap (W) of AgNPs could be manipulated by the incorporation of dendrons of various generations (0.5, 1.5, and 2.5 generations), evaluated by transmission electron microscopy. The results indicate that the nanohybrids with 1.5 generation-dendron exhibited stable, enormous, and linear-quantitative Raman enhancement in malachite green detection (1–100 ppm), due to the lowest W/D ratio (0.85 ± 0.60) and interparticle gap (7.60 ± 5.29 nm). The limit of detection (LOD) of malachite green is lower than 2.7 × 10−11 M (0.01 ppb). AgNPs@rGO-dendritic derivative nanohybrids as floating and flexible SERS substrates provide ultrasensitive and stable SERS detection in the solutions, which offers great potential for practical applications in detecting environmental pollutants.

Thermo-responsive Raman-enhanced nanocapsules were successfully fabricated by Pluronic® F127 (F127) decorated with gold nanoparticles (AuNPs) for surface-enhanced Raman scattering (SERS) detection of biomolecules. F127 nanocapsules changes from hydrophilicity (swelling) to hydrophobicity (de-swelling) when the temperature increases from 15 °C to 37 °C, owing to the lower critical solution temperature (LCST) of F127 is about 26.5 °C. The size of nanocapsules would be enormous shrinking from 160 nm to 20 nm, resulting in a significant decrease in the distance between AuNPs to enhance hot spot effect, which increases the sensitivity of SERS detection. Based on the thermo-sensitive behavior, the ratio of AuNPs and F127 would be manipulated to find the optimal SERS enhancement effect. SERS nanocapsules can rapidly detect biomolecules (adenine and R6G) with limit of detection (LOD) lower than 10

In this study, two nitrile-functionalized spiro-twisted benzoxazine monomers, namely 2,2′-((6,6,6′,6′-tetramethyl-6,6′,7,7′-tetrahydro-2H,2′H-8,8′-spirobi[indeno[5,6-e][1,3]oxazin]-3,3′(4H,4′H)-diyl)bis(4,1-phenylene))diacetonitrile (TSBZBC) and 4,4′-(6,6,6′,6′-tetramethyl-6,6′,7,7′-tetrahydro-2H,2′H-8,8′-spirobi[indeno[5,6-e][1,3]oxazin]-3,3′(4H,4′H)-diyl)dibenzonitrile (TSBZBN) were successfully developed as cross-linkable precursors. In addition, the incorporation of the nitrile group by covalent bonding onto the crosslinked spiro-twisted molecular chains improve the miscibility of SPE membranes with lithium salts while maintaining good mechanical properties. Owing to the presence of a high fractional free volume of spiro-twisted matrix, the –CN groups would have more space for rotation and vibration to assist lithium migration, especially for the benzyl cyanide-containing SPE. When combined with poly (ethylene oxide) (PEO) electrolytes, a new type of CN-containing semi-interpenetrating polymer networks for solid polymer electrolytes (SPEs) were prepared. The PEO-TSBZBC and PEO-TSBZBN composite SPEs (with 20 wt% crosslinked structure in the polymer) are denoted as the BC20 and BN20, respectively. The BC20 sample exhibited an ionic conductivity (σ) of 3.23 × 10−4 S cm−1 at 80 °C and a Li+ ion transference number of 0.187. The LiFePO4 (LFP)|BC20|Li sample exhibited a satisfactory charge–discharge capacity of 163.6 mAh g−1 at 0.1 C (with approximately 100% coulombic efficiency). Furthermore, the Li|BC20|Li cell was more stable during the Li plating/stripping process than the Li|BN20|Li and Li|PEO|Li samples. The Li|BC20|Li symmetric cell could be cycled continuously for more than 2700 h without short-circuiting. In addition, the specific capacity of the LFP|BC20|Li cell retained 87% of the original value after 50 cycles.

Three two-dimensional donor&ndash, acceptor conjugated copolymers consisting of a benzo[1,2-b:4,5-b&cent, ]dithiophene derivative and thieno[3,2-b]thiophene with a conjugated side chain were designed and synthesized for use in bulk heterojunction (BHJ) or nonfullerene polymer solar cells (PSCs). Through attaching various acceptor end groups to the conjugated side chain on the thieno[3,2-b]thiophene moiety, the electronic, photophysical, and morphological properties of these copolymers were significantly affected. It was found that the intermolecular charge transfer interactions were enhanced with the increase in the acceptor strength on the thieno[3,2-b]thiophene moiety. Moreover, a better microphase separation was obtained in the copolymer: PC71BM or ITIC blend films when a strong acceptor end group on the thieno[3,2-b]thiophene moiety was used. As a result, BHJ PSCs based on copolymer:PC71BM blend films as active layers exhibited power conversion efficiencies from 2.82% to 4.41%, while those of nonfullerene copolymer:ITIC-based inverted PSCs ranged from 6.09% to 7.25%. These results indicate the side-chain engineering on the end groups of thieno[3,2-b]thiophene unit through a vinyl bridge linkage is an effective way to adjust the photophysical properties of polymers and morphology of blend films, and also have a significant influence on devices performance.

An efficient scheme for the synthesis of 1,1-cyclopentylenylbisphenol (bisphenol CP) has been developed starting from dicyclopentadiene, a C5 byproduct from the petroleum cracking process. The synthetic steps leading to bisphenol CP consist of mostly isomerization and addition reactions, which are higher in their atom-economy efficiencies than those based upon condensation reactions. In addition, alkoxylation by cyclic carbonates converted bisphenol CP into ethoxylated and propoxylated ether diols. The transformation of hydroxyl functional groups from bisphenols to alkoxylated alcohols increased the reactivity of their hydroxyl groups toward isocyanates, as evidenced by achieving >3 times higher molecular weights of the segmented polyurethanes (PUs) in GPC analysis using alkoxylated diols as chain extenders instead of bisphenols. In addition, the incorporation of five-membered cardo-type groups onto the PU side chains through alkoxyl diols of bisphenol CP also significantly enhances the phase mixing of th...

To achieve sustainability, many kinds of bio-based epoxy resins have been developed. However, to the best of our knowledge, a 100% bio-based epoxy thermoset has rarely been reported since it needs both the epoxy resin and curing agent to be bio-based. This work provides a facile strategy to achieve epoxy thermosets with 100% bio-based content. The strategy includes the preparation of four bio-based epoxy resins 1–4 and their thermosets through the self-curing reaction of 1–4. The epoxy compounds 1–4 were prepared from the esterification of eugenol with succinyl, adipoyl, suberoyl, and 2,5-furan chloride, respectively, followed by the oxidation of the allylic bond. Through NMR, DSC, and FTIR analyses, we confirm that the self-curing reaction of 1–4 occurred through a 4-dimethylpyridine (DMAP)-catalyzed reaction of active esters and epoxides. This work successfully provides a facile strategy to achieve fully bio-based epoxy thermosets.

In this study, we first revealed green materials – poly-lysines (poly-L-lysine and poly-L-lysine blend poly-D-lysine) – as electron-extraction layers (EELs) in organic photovoltaics (OPVs). The distinct configurations of poly-lysine enantiomers were verified by conducting zeta potential analysis, and their work function (WF)-tuning capabilities for indium tin oxide (ITO) were affirmed by ultraviolet photoelectron spectroscopy (UPS). These two poly-lysine groups, with different arrangements of the amino groups that built up different surface dipoles on the ITO substrate, altered the surface energy and WF of ITO. Poly-L-lysine optimized the WF of ITO for efficient carrier transport in the OPV device, in the electron transporting layer-free OPV devices, and we observed a high power conversion efficiency (PCE) of 10.01% in the device configuration of ITO/interlayer/BHJ/MoO3/Ag. As the first examination of poly-lysine enantiomers for OPVs, we provided the WF-tuning functions – increasing polarity as an interfacial dipole is formed at the corresponding interface, and discovered a promising interfacial material possessing high efficiency and benefitting from a long-term stability to perform in a stable PCE with about 80% of its original PCE remaining after continuous heat and light treatment for 400 hours.

A new root canal sealer was developed based on urethane acrylates using polycarbonate polyol (PCPO), a macrodiol prepared in the consumption of carbon dioxide as feedstock. The superior mechanical properties and biostability nature of PCPO-based urethane acrylates were then co-crosslinked with a difunctional monomer of tripropylene glycol diarylate (TPGDA) as sealers for resin matrix. Moreover, nanoscale silicate platelets (NSPs) immobilized with silver nanoparticles (AgNPs) and/or zinc oxide nanoparticles (ZnONPs) were introduced to enhance the antibacterial effect for the sealers. The biocompatibility and the antibacterial effect were investigated by Alamar blue assay and LDH assay. In addition, the antibacterial efficiency was performed by using Enterococcus faecalis (E. faecalis) as microbial response evaluation. These results demonstrate that the PCPO-based urethane acrylates with 50 ppm of both AgNP and ZnONP immobilized on silicate platelets, i.e., Ag/ZnO@NSP, exhibited great potential as an antibacterial composite for the sealer of root canal obturation.

In this study, we synthesized 5,11-dihexyl-4,4,10,10-tetraoctylbenzo[1,2- b:4,5- b']bisthieno[4″,5″- b″:4‴,5‴- b‴]silolo[2″,3″- d:2‴,3‴- d']thiophene (ArSi) as a ladder-type electron-rich core for the preparation of three acceptor-donor-acceptor-type nonfullerene acceptors (NFAs)-ArSiID, ArSiID-F, and ArSiID-Cl-featuring (3-oxo-2,3-dihydro-1 H-inden-1-ylidene)malononitrile (ID), 2-(5,6-difluoro-3-oxo-2,3-dihydro-1 H-inden-1-ylidene)malononitrile (ID-F), and 2-(5,6-dichloro-3-oxo-2,3-dihydro-1 H-inden-1-ylidene)malononitrile (ID-Cl) as peripheral electron-poor units, respectively. These molecules exhibit strong absorption covering the region of 600-850 nm. The incorporation of the halogen atoms onto the terminal units adjusted the energy levels and light-harvesting ability of these materials. We employed the conjugated polymers J51 and PBDB-T, having middle optical energy gaps as donor together with these ArSi derivatives as acceptor to study the blend film morphology and the corresponding organic photovoltaic (OPV) performances. After optimization with device engineering works, a PBDB-T:ArSiID-F-based device with a power conversion efficiency up to 9.4% was achieved. This study is the first case to examine the effects of various halogen modifications on the performance of ArSi derivatives that serve as NFAs for OPVs. Our findings should encourage further investigations on this rarely studied core structure for optoelectronic applications.

A series of twisted N,N-linked benzo[ghi]-perylenetriimide dimers (t-BPTI) with various lengths of the α-branched alkyl side chain at the six-membered imide ring position was designed, synthesized, and characterized. These compounds showed the low-lying LUMO energy level of -3.78 eV, which was similar to that of PC61 BM (-3.71 eV), but with intensive optical absorption in the range 350-500 nm. The twisted molecular geometry with two nearly perpendicular BPTI planes achieved a favorable nanoscale phase separation by relieving the self-aggregation of rigid BPTI units in blend films. The acceptor t-BPTI-3 unit with the longest alkyl side chains has been demonstrated to be an efficient electron acceptor in solution-processed bulk heterojunction organic photovoltaics (OPV), giving a power conversion efficiency of 3.68 % when using conjugated polymer PTB7-Th as the donor and without additional treatments.

Three dimesitylborane-containing fluorophores with various π-conjugated systems attached at the 9th position of carbazole, namely, 9-(4′-bromobiphenyl-4-yl)-9H-carbazole (Cz9Ph2B), 9-(4-(5-(dimesitylboryl)thiophen-2-yl)phenyl)-9H-carbazole (Cz9ThPhB), and 9-(4-(4-(dimesitylboryl)styryl)phenyl)-9H-carbazole (Cz9SB) were synthesized and their photophysical and electroluminescent properties were investigated for application in nondoped blue OLEDs as well as red phosphorescent OLEDs (PhOLEDs). The electron-accepting dimesitylboryl group and various π-conjugated segments appended to the electron-donating carbazole moiety impart the three fluorophores with bipolar transporting ability, and their energy levels are matched with those of the adjacent carrier-transporting layers. These bulky fluorophores are thermally stable with glass transition temperatures and degradation temperatures reaching up to 105 and 383 °C, respectively. In addition, efficient nondoped Cz9PhThB- and Cz9SB-based blue OLEDs with maximum currents of 1.51 and 4.03 cd A−1 and external quantum efficiencies (EQE) of 2.30 and 4.72% were achieved, respectively. Notably, the Cz9Ph2B-based red PhOLEDs exhibits a relatively low turn-on voltage (3.3 V) and high electroluminescence efficiencies (maximum current = 23.12 cd A−1 and EQE = 14.10%). Their performance is superior to that of the corresponding device using conventional 4,4′-N,N′-dicarbazolbiphenyl as the host material. Moreover, a maximum brightness of 39700 cd m−2 was also achieved.

This study demonstrates a simple and convenient two-step one-pot, highly efficient process of recycling poly(bisphenol A carbonate), i.e., PC, into versatile intermediates for polymers such as polyurethanes (PUs). Via a highly efficient and selective amine carbonylation reaction, PC is depolymerized by aliphatic diamines forming hydroxyl-N,N′-diphenylene-isopropylidenyl biscarbamates (hydroxyl DP-biscarbamates) as major interim prepolymers. Both short- and long-chained prepolymers are prepared with their respective diamines, and the prepolymers are chain-extended with commercially available regents such as diisocyanates to produce a variety of PU polymers. Hence, PC is cleaved into pieces of soluble hydroxyl DP-biscarbamates first and then reassembled into new linear polymers without resorting to a separation process. Different from PC-recycling processes reported in the literature, each carbonate group of PC in this new process is fully utilized for making one carbamate group and one hydroxyl terminated ...

NORYL™ SA9000 resin is a commercialized telechelic PPO oligomer with phenyl methacrylate end groups. However, neat SA9000 thermoset is brittle after thermally curing. To find a method to enhance the toughness of neat SA9000 thermoset, three model reactions are designed. The first one is the 4-dimethylaminopyridine (DMAP)-catalyzed homopolymerization of glycidyl phenyl ether. The second one is the reaction of glycidyl phenyl ether and phenyl acetate in the presence of DMAP. The third one is the reaction of glycidyl phenyl ether and phenyl methacrylate in the presence DMAP. Through 1H NMR analysis, the product is 1,3-diphenoxy-2-acetoxypropane and 1,3-diphenoxy-2-methacryalatepropane, respectively, for model reactions 2 and 3. According to the structure of products, we identify the reaction mechanisms between the phenyl acetate and epoxy, and between the phenyl methacrylate and epoxy. Based on the knowledge, we used two commercialized epoxy resin (DGEBA and HP7200) to copolymerize with SA9000 in the presence of DMAP and tert-butyl cumyl peroxide (TBCP). The toughness of the thermosets are significantly improved, which means the brittle drawback of neat SA9000 thermoset has been solved. Homogeneous, flexible thermosetting films with high glass transition temperatures, low dielectric constants, and extremely low dissipation factors are obtained.

Through the use of organic/inorganic hybrid dispersants—which are composed of polymeric dispersant and two-dimension nanomaterial graphene oxide (GO)—copper nanoparticles (CuNPs) were found to exhibit nano stability, air-stable characteristics, as well as long-term conductive stability. The polymeric dispersant consists of branched poly(oxyethylene)-segmented esters of trimellitic anhydride adduct (polyethylene glycol−trimethylolpropane−trimellitic anhydride, designated as PTT). PTT acts as a stabilizer for CuNPs, which are synthesized via in situ polymerization and redox reaction of the precursor Cu(CH3COO)2 within an aqueous system, and use graphene oxide to avoid the reduction reaction of CuNPs. The results show that after 30 days of storage the CuNPs/PTT/GO composite film maintains a highly conductive network (9.06 × 10−1 Ω/sq). These results indicate that organic/inorganic PTT/GO hybrid dispersants can effectively maintain the conductivity stability of CuNPs and address the problem of CuNP oxidation. Finally, the new CuNPs/PTT/GO composite film was applied to the electrocardiogram (ECG) smart clothes. This way, a stable and antioxidant-sensing electrode can be produced, which is expected to serve as a long-term ECG monitoring device.