Search

Abstract The triglyceride-glucose (TyG) index is emerging as a promising marker for insulin resistance and serves as an independent risk predictor for cardiovascular outcomes. The coronary angiography-derived index of microcirculatory resistance (AMR) is computed to evaluate coronary microcirculation. However, the association between the TyG index and the AMR in patients with type 2 diabetes mellitus (T2DM) and ST-segment elevation myocardial infarction (STEMI) remains unclear. We consecutively recruited 168 patients with T2DM and STEMI who underwent primary percutaneous coronary intervention (pPCI) at Taizhou People’s Hospital from January 2022 to December 2023. Patients were classified into low AMR group (AMR < 2.5) and high AMR group (AMR ≥ 2.5). The TyG index was calculated using the formula: ln [plasma triglyceride (mg/dL) × fasting blood glucose (mg/dL)/2]. The study enrolled 81 patients in the low AMR group and 87 in the high AMR group, with the TyG index being significantly higher in the high AMR group. Multivariable logistic regression analysis revealed a significant association between the TyG index and high AMR after adjusting for confounding variables (odds ratio: 2.449, 95% confidence interval: 1.421–4.220, and p = 0.001). The area under the curve for the TyG index predicting high AMR was 0.650 (95% confidence interval: 0.57–0.73, p

Abstract Passive solar membrane distillation (MD) is an emerging technology to alleviate water scarcity. Recently, its performance has been enhanced by multistage design, though the gains are marginal due to constrained temperature and vapor pressure gradients across the device. This makes condenser cooling enhancement a questionable choice. We argue that condenser heating could suppress the marginal effect of multistage solar MD by unlocking the moisture transport limit in all distillation stages. Here, we propose a stage temperature boosting (STB) concept that directs low-temperature heat to the condensers in the last stages, enhancing moisture transport across all stages. Through STB in the last two stages with a heat flux of 250 W m−2, a stage-averaged distillation flux of 1.13 L m−2 h−1 S−1 was demonstrated using an 8-stage MD device under one-sun illumination. This represents an 88% enhancement over the state-of-the-art 10-stage solar MD devices. More notably, our analysis indicates that 16-stage STB-MD devices driven by solar energy and waste heat can effectively compete with existing photovoltaic reverse osmosis (PV-RO) systems, potentially elevating freshwater production with low-temperature heat sources.

Abstract Sorption-based atmospheric water harvesting (SAWH) has received unprecedented attention as a future water and energy platform. However, the water productivity of SAWH systems is still constrained by the slow sorption kinetics at material and component levels and inefficient condensation. Here, we report a facile method to prepare hygroscopic interconnected porous gel (HIPG) with fast sorption-desorption kinetics, high scalability and stability, and strong adhesion property for highly efficient SAWH. We further design a solar-wind coupling driven SAWH device with collaborative heat and mass enhancement achieving continuous water production. Concentrated sunlight contributes to enhancing the desorption and condensation synergistically, and natural wind is introduced to drive the device operation and improve the sorption kinetics. The device demonstrated record high working performance of 14.9 Lwater m−2 day−1 and thermal efficiency of 25.7% in indoor experiments and 3.5–8.9 Lwater m−2 day−1 in outdoor experiments by solar concentration without any other energy consumption. This work provides an up-and-coming pathway to realize highly efficient and sustainable clean water supply for off-grid and arid regions.

The substantial energy demand associated with active heating, cooling, and ventilation presents a pressing challenge for sustainable development. Conventional systems rely heavily on electricity, contributing to environmental strain and high energy costs. Passive radiative cooling and solar heating offer promising alternatives but are often limited by the spatial-temporal mismatch between energy supply and demand, especially in arid climates with extreme diurnal temperature fluctuations. In a recent Nature Communications paper, Kim et al. reported a novel self-switchable passive isothermal film, co-driven by radiative cooling and solar heating, and coupled with sorption thermal energy storage and salt dissolution-based cold storage. This innovative design enables all-day temperature regulation in harsh climate conditions, offering a compelling solution for building energy conservation.

Summary: Desiccant-coated heat exchangers provide a practical solution for the efficient removal of moisture from the air. Here, we present a protocol to synthesize an ultra-hygroscopic polymer to develop a LiCl loaded in curdlan hydrogel (LiCl@Cur)-coated heat exchanger for deep dehumidification. We describe steps for preparing the curdlan gel solution, hydrogel, LiCl solution, and LiCl@Cur. We then detail procedures for preparing curdlan-coated and LiCl@Cur-coated heat exchangers. The coated heat exchanger described in this protocol has a maximum dehumidification capacity of 12 g/kg.For complete details on the use and execution of this protocol, please refer to Pan et al. (2023).1 : Publisher’s note: Undertaking any experimental protocol requires adherence to local institutional guidelines for laboratory safety and ethics.

Background: percutaneous coronary intervention (PCI) has become the mainstay of treatment for atherosclerotic cardiovascular disease (ASCVD). Inflammatory factors have been shown to be involved in the initiation and progression of ASCVD. After PCI, the persistence of inflammation, especially the inflammation released at the target lesion, may affect the stability of non-target lesion plaques. Interleukin-6 (IL-6) is one of the most common inflammatory factors, however studies about the influence of IL-6 on the progression of non-target lesions (NTLs) of coronary artery are limited. This study investigated whether serum IL-6 levels can affect the progression of NTLs after coronary stent implantation. Methods: We performed a retrospective cohort study including 441 patients undergoing coronary angiography (CAG) and stent implantation, who had at least one NTL, between January 2019 and December 2021. They underwent followup CAG 9 to 12 months after PCI. Quartile grouping was based on serum IL-6 levels following readmission. The relationship between serum IL-6 levels and the progression of NTLs after coronary stent implantation was analyzed by using logistic regression analysis and restricted cubic spline regression. Predictive value of IL-6 on NTL progression was evaluated using the receiver operating characteristic (ROC) curve. Results: When compared to the first quartile (Q1) group, the probability of NTL progression was increased in Q2 (adjusted odds ratio (aOR) 3.06, 95% CI 1.29–7.29), Q3 (aOR 3.55, 95% CI 1.52–8.26), and Q4 group (aOR 7.51, 95% CI 3.30–17.05), with a trend test p < 0.001. With the increase of IL-6 levels, the risk of progression of NTLs gradually increased, and there was a non-linear relationship between IL-6 and progression of NTLs (p < 0.001). The ROC curve showed that the critical value of the serum IL-6 level was 12.652 pg/mL (area under the curve is 0.673, sensitivity is 54.5%, specificity is 70.9%, p < 0.05). Conclusions: A high serum IL-6 level is an independent risk factor for the progression of NTLs after coronary stent implantation, and has certain predictive value for the progression of NTLs.

Abstract Heating decarbonization is a major challenge for China to meet its 2060 carbon neutral commitment, yet most existing studies on China’s carbon neutrality focus on supply side (e.g., grid decarbonization, zero-carbon fuel) rather than demand side (e.g., heating and cooling in buildings and industry). In terms of end use energy consumption, heating and cooling accounts for 50% of the total energy consumption, and heat pumps would be an effective driver for heating decarbonization along with the decarbonization on power generation side. Previous study has discussed the underestimated role of the heat pump in achieving China’s goal of carbon neutrality by 2060. In this paper, various investigation and assessments on heat pumps from research to applications are presented. The maximum decarbonization potential from heat pump in a carbon neutral China future could reach around 1532Mton and 670Mton for buildings and industrial heating respectively, which show nearly 2 billion tons CO2 emission reduction, 20% current CO2 emission in China. Moreover, a region-specific technology roadmap for heat pump development in China is suggested. With collaborated efforts from government incentive, technology R&D, and market regulation, heat pump could play a significant role in China’s 2060 carbon neutrality.

Abstract Water and electricity scarcity are two global challenges, especially in arid and remote areas. Harnessing ubiquitous moisture and sunlight for water and power generation is a sustainable route to address these challenges. Herein, we report a moisture-induced energy harvesting strategy to realize efficient sorption-based atmospheric water harvesting (SAWH) and 24-hour thermoelectric power generation (TEPG) by synergistically utilizing moisture-induced sorption/desorption heats of SAWH, solar energy in the daytime and radiative cooling in the nighttime. Notably, the synergistic effects significantly improve all-day thermoelectric power density (~346%) and accelerate atmospheric water harvesting compared with conventional designs. We further demonstrate moisture-induced energy harvesting for a hybrid SAWH-TEPG device, exhibiting high water production of 750 g m−2, together with impressive thermoelectric power density up to 685 mW m−2 in the daytime and 21 mW m−2 in the nighttime. Our work provides a promising approach to realizing sustainable water production and power generation at anytime and anywhere.

Metal–organic frameworks (MOFs) are promising for indoor humidity regulation due to steep stepwise water uptake and moderate regeneration temperature. Current approaches for performance improvement of MOFs such as impregnating hygroscopic salts and grafting functional groups face the challenge of corrosion and instability. Herein, a template‐guided tuning strategy is proposed to synthesize binary nanocomposite. Highly ordered mesoporous channels of MCM‐41 provide uniform nucleation sites for MOF growth, enabling a 21.5% promotion of specific surface area (3188.14 m2 g−1) and 23.4% improvement of water uptake (1.53 g g−1 at 20°C/90% relative humidity) for the nanocomposite compared with parent MIL‐101(Cr). The fast kinetics and superior stability together guarantee its practical application. Further, a paradigm of continuous indoor humidity regulation driven by sunlight is demonstrated, which realizes smart regulation of the indoor humidity to the human comfort zone (40–60%) with near‐zero energy input.

Sorption-based atmospheric water harvesting has the potential to realize flexible water production but reaching high water yield in semi-arid climate is still challenging. Here, the authors report a portable and modularized water harvester with scalable, low-cost, and lightweight hygroscopic composite sorbent which shows an exceptional water production in semi-arid climate with low relative humidity of 15%.

Thermally-driven water-sorption refrigeration is a promising environmentally friendly technology, but finding suitable porous materials is challenging. The authors report a very high coefficient of performance using a low-cost zeolite-like aluminophosphate as a water sorbent, suitable for use with low-grade thermal energy.

Summary: Atmospheric water harvesting (AWH) offers a solution for efficiently extracting water from the air. In this protocol, we detail the steps to develop a composite sorbent loaded with hygroscopic salts and lithium chloride (LiCl) and based on hydrogel, acrylamide monomer (AM), and carbon nanotubes (CNTs). We describe a streamlined experimental approach for the synthesis of the honeycomb-optimized hydrogel-based composite adsorbent (PCLG) by in situ polymerization. The produced sorbent exhibits ultra-high adsorption/desorption capacity per unit volume and low-temperature desorption.For complete details on the use and execution of this protocol, please refer to Wang et al. (2022). : Publisher’s note: Undertaking any experimental protocol requires adherence to local institutional guidelines for laboratory safety and ethics.

Abstract Atmospheric water harvesting (AWH) provides a fascinating chance to facilitate a sustainable water supply, which obtains considerable attention recently. However, ignoring the energy efficiency of AWH leads to high energy consumption in current prototypes (ca. 101 to 102 MJ kg−1), misfitting with the high‐strung and complicated water‐energy nexus. In this perspective, a robust evaluation of existing AWHs is conducted and a detailed way to high‐efficiency AWH is paved. The results suggest that using cooling‐assisted adsorption will weaken the bounds of climate to sorbent selections and have the potential to improve efficiency by more than 50%. For device design, the authors deeply elucidate how to perfect heat/mass transfer to narrow the gap between lab and practices. Reducing heat loss, recovering heat and structured sorbent are the main paths to improve efficiency on the device scale, which is more significant for a large‐scale AWH. Besides efficiency, the techno‐economic evaluation reveals that developing a cost‐effective AWH is also crucial for sustainability, which can be contributed by green synthesis routes and biomass‐based sorbents. These analyses provide a uniform platform to guide the next‐generation AWH to mitigate the global water crisis.

Abstract Sorption‐based atmospheric water harvesting (SAWH) holds huge potential due to its freshwater capabilities for alleviating water scarcity stress. The two essential parts, sorbent material and system structure, dominate the water sorption–desorption performance and the total water productivity for SAWH system together. Attributed to the superiorities in aspects of sorption–desorption performance, scalability, and compatibility in practical SAWH devices, hygroscopic porous polymers (HPPs) as next‐generation sorbents are recently going through a vast surge. However, as HPPs’ sorption mechanism, performance, and applied potential lack comprehensive and accurate guidelines, SAWH's subsequent development is restricted. To address the aforementioned problems, this review introduces HPPs’ recent development related to mechanism, performance, and application. Furthermore, corresponding optimized strategies for both HPP‐based sorbent bed and coupling structural design are proposed. Finally, original research routes are directed to develop next‐generation HPP‐based SAWH systems. The presented guidelines and insights can influence and inspire the future development of SAWH technology, further achieving SAWH's practical applications.

A distributed integrated cooling system, including cold supply and cold storage, can store cold energy during the valley electricity period and release cold energy during peak electricity period, thus effectively realizing cutting peak electricity loads can achieve higher economic performance and capacity factors. However, a distributed integrated cooling system’s planning suffers from lacking systematic guidance in planning and optimal operation. This paper presented an efficient analytical planning method considering cutting peak electricity power and the corresponding compensating cost and inducted the condition of applying an integrated cooling system. The critical operating electricity price and economic equilibrium electricity price are presented as two indexes to evaluate the economic condition of operating and constructing an integrated cooling system. The analytical planning model is validated to be exact and efficient by the numerical simulation due to less iteration. The planning results show that a distributed integrated cooling system is fully utilized during a year, but the relative ability to cut peak electricity load decreases with electrical loads. Because the compensating cost is lower than the price differences between peak and flat-peak electricity prices, which is cheaper than a battery, a distributed integrated cooling system is a cost-effective technology for cutting peak electricity loads.

Summary: Sorption-based atmospheric water harvesting (SAWH) is a feasible and sustainable approach to address water scarcity issues. Featuring the high affinity of hygroscopic salts with water vapor, salt-based composite sorbents have been widely used. However, the risk of salt solution leakage is still challenging. In this protocol, we introduce a porous waterproof and moisture-permeable membrane encapsulation technique to develop salt-based sorbents. The high salt content composites (HSCC-Ex) exhibit remarkably high salt content of 80 wt % without the risk of leakage.For complete details on the use and execution of this protocol, please refer to Shan et al. (2021).

Summary: Condensation of humid air is an important process in thermal and process engineering and a subject of many currently research-intensive scientific domains, such as atmospheric water harvesting and seawater desalination. The nature of (water) vapor condensation in the presence of non-condensable gas (NCG) such as air differs significantly from the case with the pure, quiescent vapor condensation. In the literature, simple models that describe the forced flow condensation of water vapor in the presence of air on a series of vertical flat plates are hard to find. Here we present a simple and computationally efficient semi-empirical correlation describing forced flow condensation from humid air inside vertical channels formed by flat plates. The correlation accounts air as a non-condensing gas, different heights of vertical plates, and different thermal-hydraulic parameters. The correlation has been experimentally validated and shows excellent agreement, as 90% of theoretically predicted values are within ±12% of experimental data.

Summary: Sorption-based atmospheric water harvesting (SAWH) is recognized as a feasible and sustainable approach to address global water scarcity in arid regions. However, easy-to-prepare and inexpensive salt-based sorbents have stringent requirements referring to sorption duration and environmental humidity; otherwise, the leakage of salt solution can occur. Here, we develop a composite sorbent with remarkably high salt content of 80 wt % and without the risk of leakage by introducing a polytetrafluoroethylene membrane encapsulation method. The developed composite HSCC-E10 shows both fast sorption kinetics inherent to the matrix of composites and high absorption capacity of hygroscopic salt solutions, achieving ultra-high sorption capacity of 3.75 g/g, 2.83 g/g, and 1.47 g/g for 90%, 70%, and 30% relative humidity (RH), respectively. A lab-scale device is developed demonstrating 560 mL/m2 water yield under outdoor natural sunlight. The applicability of proposed sorbents could pave the road for future middle- or large-scale applications, such as vehicle-mounted and continuous SAWH.

Summary: There is broad demand for humidity control for industrial, commercial, and residential applications. Current humidity pumping technologies require intensive maintenance because of the complexity of their mechanical structures. Furthermore, indirect utilization of solar energy increases both cost and energy loss. Here, we demonstrate a new humidity pumping concept based on multilayer moisture permeable panels. Such panels, with a simple structure, may allow the penetration of moisture from indoor (adsorption) to outdoor (desorption) with little heat loss. One-sun illumination is introduced as the direct energy source. A proof-of-concept prototype is designed and established, successfully dehumidifying indoor air with the best dehumidification rate of 33.8 g⋅m−2⋅h−1. By applying such humidity pump, the indoor latent heat load can be handled independently, without any auxiliary unit, thus consuming no electricity. : Engineering; Energy Systems; Materials Science; Energy Materials Subject Areas: Engineering, Energy Systems, Materials Science, Energy Materials

Summary: Numerous studies have focused on tailoring materials for sorption-based atmospheric water harvesting (AWH) in arid climates, but both the design and modification of materials are a compromise for specific conditions and even sacrifice the nature of S-shaped isotherm. Inspired by the manipulation method of air humidity, we herein propose a regulation strategy of sorbent stepwise position by inducing an inner cooling source without changing the intrinsic properties of metal-organic framework (MOF). Significant improvement of water uptake of MIL-101(Cr) coating can be reached from 0.13 to 1.05 g/g with the cooling temperature of 14°C in typical arid climate (25°C and 30% relative humidity [RH]). Mechanism of stepwise position migration is elucidated and performance of AWH device based on Peltier cooler is enhanced as compared to that without regulation. This study weakens the limitation of the exclusive tailoring materials for specific conditions and would provide a promising perspective for next-generation scalable and variable weather-adaptive AWH systems.

Steam generation process is closely related to energy conversion and cleaner energy utilization, and the industrial steam is even regarded as the currency of heat with significant social and economic value. Herein, the possible industrial steam generation paths are analyzed based upon thermodynamics analysis, in which fossil fuel, electric, and heat‐pump heating are considered. The large‐temperature‐lift heat‐pump heating for steam generation is proved to be a most reasonable way with high‐efficiency and wide adaptability. Furthermore, a possible system sketch is proposed, in which the heat pump is used for preheating for low‐temperature evaporation and the generated steam can be thus compressed with a steam compressor to the expected high‐temperature (pressure) steam. The key parameters of the heat pump for steam generation are ascertained and the subsequent optimization space is discussed. The results show that the proposed steam‐generation path has clear performance advantages and potential for industrial steam generation, which could be a sustainable heating system for industry.

This study presents a thermodynamic formulation to capture the relationship between the adsorption interaction energy and adsorbent-morphological properties, which can be further extended into surface coverage. Employing the inverse gas chromatography method, the adsorbate uptakes are measured in Henry's law region, from which the energetic behaviors of a single component adsorbate-adsorbent system are calculated in terms of enthalpy and entropy of the adsorbed phase in very low-pressure regions. A thermodynamic formulation is established between the specific entropy and Henry's law constant, including the pore volume of the adsorbents, and one can predict the isosteric heats and adsorbent's pore size for activated carbon + ethanol system by extending the proposed linear trend. These findings could significantly contribute towards tailoring the adsorbent materials for the design of an adsorption bed with a minimal or maximum driving force depending on the types of heat transformation applications.

Objective We aimed to determine whether the prognostic value of the shock index (SI) and its derivatives is better than that of the Thrombolysis In Myocardial Infarction risk index (TRI) for predicting adverse outcomes in patients with ST-segment elevation myocardial infarction (STEMI) undergoing primary percutaneous coronary intervention (PCI). Methods A total of 257 patients with STEMI undergoing primary PCI from January 2018 to June 2019 were analyzed in a retrospective cohort study. The SI, modified shock index (MSI), age SI (age × the SI), age MSI (age × the MSI), and TRI at admission were calculated. Clinical endpoints were in-hospital complications, including all-cause mortality, acute heart failure, cardiac shock, mechanical complications, re-infarction, and life-threatening arrhythmia. Results Multivariate analyses showed that a high SI, MSI, age SI, age MSI, and TRI at admission were associated with a significantly higher rate of in-hospital complications. The predictive value of the age SI and age MSI was comparable with that of the TRI (area under the receiver operating characteristic curve: z = 1.313 and z = 0.882, respectively) for predicting in-hospital complications. Conclusions The age SI and age MSI appear to be similar to the TRI for predicting in-hospital complications in patients with STEMI undergoing primary PCI.

Decarbonization of the industrial sector is one of the most important keys to reducing global warming. Energy demands and associated emissions in the industrial sector are continuously increasing. The utilization of high temperature heat pumps (HTHPs) operating with natural fluids presents an environmentally friendly solution with great potential to increase energy efficiency and reduce emissions in industrial processes. Ammonia-water absorption–compression heat pumps (ACHPs) combine the technologies of an absorption and vapor compression heat pump using a zeotropic mixture of ammonia and water as working fluid. The given characteristics, such as the ability to achieve high sink temperatures with comparably large temperature lifts and high coefficient of performance (COP) make the ACHP interesting for utilization in various industrial high temperature applications. This work reviews the state of technology and identifies existing challenges based on conducted experimental investigations. In this context, 23 references with capacities ranging from 1.4 kW to 4500 kW are evaluated, achieving sink outlet temperatures from 45 °C to 115 °C and COPs from 1.4 to 11.3. Existing challenges are identified for the compressor concerning discharge temperature and lubrication, for the absorber and desorber design for operation and liquid–vapor mixing and distribution and the choice of solution pump. Recent developments and promising solutions are then highlighted and presented in a comprehensive overview. Finally, future trends for further studies are discussed. The purpose of this study is to serve as a starting point for further research by connecting theoretical approaches, possible solutions and experimental results as a resource for further developments of ammonia-water ACHP systems at high temperature operation.

Purpose. Cryoprotectants (CPA) for stem cells from umbilical cord blood (UCB) have been widely developed based on empirical evidence, but there is no consensus on a standard protocol of preservation of the UCB cells. Methods. In this study, UCB from 115 donors was collected. Each unit of UCB was divided into four equal parts and frozen in different kinds of cryoprotectant as follows: group A, 10% ethylene glycol and 2.0% dimethyl sulfoxide (DMSO) (v/v); group B, 10% DMSO and 2.0% dextran-40; group C, 2.5% DMSO (v/v) + 30 mmol/L trehalose; and group D, without CPA. Results. CD34+, cell viability, colony forming units (CFUs), and cell apoptosis of pre- and postcryopreservation using three cryoprotectants were analyzed. After thawing, significant differences in CD34+ count, CFUs, cell apoptosis, and cell viability were observed among the four groups (P

BACKGROUND:Human umbilical cord-derived mesenchymal stem cells (hUC-MSCs) are in the foreground as a preferable application for treating diseases. However, the safety of hUC-MSCs after long-term culturing in vitro in serum-free medium remains unclear. METHODS:hUC-MSCs were separated by adherent tissue culture. hUC-MSCs were cultured in serum-free MesenCult-XF medium and FBS-bases DMEM complete medium. At the 1st, 3rd, 5th, 8th, 10th, and 15th passage, the differentiation of MSCs into osteogenic, chondrogenic, and adipogenic cells was detected, and MTT, surface antigens were measured. Tumorigenicity was analyzed at the 15th passage. Conventional karyotyping was performed at passage 0, 8, and 15. The telomerase activity of hUC-MSCs at passage 1-15 was analyzed. RESULTS:Flow cytometry analysis showed that very high expression was detected for CD105, CD73, and CD90 and very low expression for CD45, CD34, CD14, CD79a, and HLA-DR. MSCs could differentiate into osteocytes, chondrocytes, and adipocytes in vitro. There was no obvious chromosome elimination, displacement, or chromosomal imbalance as determined from the guidelines of the International System for Human Cytogenetic Nomenclature. Telomerase activity was down-regulated significantly when the culture time was prolonged. Further, no tumors formed in rats injected with hUC-MSCs (P15) cultured in serum-free and in serum-containing conditions. CONCLUSION:Our data showed that hUC-MSCs met the International Society for Cellular Therapy standards for conditions of long-term in vitro culturing at P15. Since hUC-MSCs can be safely expanded in vitro and are not susceptible to malignant transformation in serum-free medium, these cells are suitable for cell therapy.

To store low-temperature heat below 100 °C, novel composite sorbents were developed by impregnating LiCl into expanded vermiculite (EVM) in this study. Five kinds of composite sorbents were prepared using different salt concentrations, and the optimal sorbent for application was selected by comparing both the sorption characteristics and energy storage density. Textural properties of composite sorbents were obtained by extreme-resolution field emission scanning electron microscopy (ER-SEM) and an automatic mercury porosimeter. After excluding two composite sorbents which would possibly exhibit solution leakage in practical thermal energy storage (TES) system, thermochemical characterizations were implemented through simulative sorption experiments at 30 °C and 60% RH. Analyses of thermogravimetric analysis/differential scanning calorimetry (TGA/DSC) curves indicate that water uptake of EVM/LiCl composite sorbents is divided into three parts: physical adsorption of EVM, chemical adsorption of LiCl crystal, and liquid–gas absorption of LiCl solution. Energy storage potential was evaluated by theoretical calculation based on TGA/DSC curves. Overall, EVMLiCl20 was selected as the optimal composite sorbent with water uptake of 1.41 g/g, mass energy storage density of 1.21 kWh/kg, and volume energy storage density of 171.61 kWh/m3.