Search

Investigations are presented for the preparation of a model hemostatic dressing that would exhibit an adequate hemostatic capacity in injuries and surgical wounds, an antibacterial activity to prevent primary and secondary infections, and offer safety in use. The Hemoguard dressing has been designed as a powder prepared from the complex chitosan/alginate Na/Ca in the form of micro- and nano-fibrids. Useful antibacterial and hemostatic properties of Hemoguard, which would qualify the material as first aid dressing and a temporary protection of injury wounds in field conditions, were assessed. Biocompatibility of the dressing was confirmed by biological in vitro examinations.

In this work the physicochemical and biological properties of nanocrystalline TiO2 thin films were investigated. Thin films were prepared by magnetron sputtering method. Their properties were examined by X-ray diffraction, photoelectron spectroscopy, atomic force microscopy, optical transmission method and optical profiler. Moreover, surface wettability and scratch resistance were determined. It was found that as-deposited coatings were nanocrystalline and had TiO2-anatase structure, built from crystallites in size of 24 nm. The surface of the films was homogenous, composed of closely packed grains and hydrophilic. Due to nanocrystalline structure thin films exhibited good scratch resistance. The results were correlated to the biological activity (in vitro) of thin films. Morphological changes of mouse fibroblasts (L929 cell line) after contact with the surface of TiO2 films were evaluated with the use of a contrast-phase microscope, while their viability was tested by MTT colorimetric assay. The viability of cell line upon contact with the surface of nanocrystalline TiO2 film was comparable to the control sample. L929 cells had homogenous cytoplasm and were forming a confluent monofilm, while lysis and inhibition of cell growth was not observed. Moreover, the viability in contact with surface of examined films was high. This confirms non-cytotoxic effect of TiO2 film surface on mouse fibroblasts.

Fluoride is one of the elements commonly present in the human environment. Due to its characteristics, it is very widely used in medicine, dentistry, industry or agriculture. On the other hand, its universality possesses a real threat to the human body in the form of acute and chronic poisoning. The aim of this paper is to characterize the properties of fluoride and its effects on the human body, as well as the sources of its occurrence. Particular emphasis is placed on the safety of its use and optimal dosage intake, which prevents accumulation and reduces its potential side effects. The positive effect of proper fluoride supply is widely described. In order to avoid overdose, it is best to consult a specialist to properly select the dosage.

Laparoscopic surgery is undergoing rapid development. Replacing the traditional method of joining cut tissues with sutures or staples could greatly simplify and speed up laparoscopic procedures. This alternative could undoubtedly be adhesives. For decades, scientists have been working on a material to bond tissues together to create the best possible conditions for tissue regeneration. The results of research on tissue adhesives achieved over the past years show comparable treatment effects to traditional methods. Tissue adhesives are a good alternative to surgical sutures in wound closure. This article is a review of the most important groups of tissue adhesives including their properties and possible applications. Recent reports on the development of biological adhesives are also discussed.

The literature lacks conclusive evidence that lymphatic vessels can form in the dental pulp. Lymphangiogenesis is believed to occur in an inflamed pulp. If one defines lymphangiogenesis as the development of lymphatic vessels from already existing ones, such a mechanism is possible only when lymphatic vessels are present in healthy teeth. This paper aims to identify lymphatic vessels in the dental pulp using microscopic and immunohistochemical methods under physiological and pathological conditions. The tissue material consisted of human teeth intended for extraction. Our studies and results suggest a moderate correlation between pulp inflammation and the formation of new vessels, including lymphatic vessels.

A knitted implant, unilaterally modified with plasma-assisted chemical-vapor deposition (PACVD), and with a nano-layer of fluorine derivative supplementation, for reducing the risk of complications related to adhesions, and the formation of a thick postoperative scar was prepared. The biological evaluation of designed or modified medical devices is the main aspect of preclinical research. If such studies use a medical device with prolonged contact with connective tissue (more than 30 days), biocompatibility studies require a safety assessment in terms of toxicity in vitro and in vivo, allergenicity, irritation, and cancerogenicity, reproductive and developmental toxicity. The ultimate aspect of biological evaluation is biofunctionality, and evaluation of the local tissue response after implantation, resulting in the determination of all aspects of local biocompatibility with the implemented synthetic material. The implantation of PACVD-modified materials in muscle allows us to estimate the local irritation effect on the connective tissue, determining the risk of scar formation, whereas implantation of the above-mentioned knitted fabric into the abdominal wall, assists with evaluating the risk of fistula formation-the main post-surgical complications. The research aimed to evaluate the local reaction of the soft tissues after the implantation of the knitted implants modified with PACVD of the fluoropolymer in the nanostuctural form. The local effect that occurred during the implantation of the designed implants was quantitatively and qualitatively evaluated when PACVD unmodified (reference), and modified medical devices were implanted in the abdominal cavity (intra-abdominal position) for 12 or into the muscles for 56 weeks. The comparative semi-quantitative histological assessment included the severity of inflammatory cells (multinucleated cells, lymphocytes, plasma cells, macrophages, giant cells) and the tissue response (necrosis, neovascularization, fibrosis, and fat infiltration) on a five-point scale. The knitted implants modified by PACVD did not indicate cumulative tissue response when they were implanted in the muscle and intra-abdominally with direct contact with the viscera. They reduced local tissue reaction (score -2.71 after 56 weeks of the implantation) and internal organ adhesion (irritation score -2.01 and adhesion susceptibility -0.3 after 12 weeks of the implantation) compared with the reference (unmodified by PACVD) knitted implant, which had an identical structure and was made of the same source.

Background: From one year to another, dentists have access to more procedures using modern techniques. Many of them can improve the effectiveness of dental procedures and frequently facilitate and accelerate them., Objectives: Technically advanced devices are an important part of modern dentistry. Over the years, there were developed technologies like ultrasounds, lasers, air abrasion, ozonotherapy, caries diagnostic methods, chemomechanical caries removal (CMCR), pulp vitality tests, computer-controlled local anesthetic delivery (CCLAD). The aim of this study was to investigate the requirement of Polish dentists for such technologies., Methods: An anonymous questionnaire was posted on a social media group of dentists from Poland. 187 responses were obtained., Results: It turned out that almost every respondent uses ultrasounds, but other technologies are not as popular. 43% use CCLAD, 33% use diagnostic methods, 28% use air abrasion, 25% use dental lasers, 21% use CMCR, 18% use pulp vitality tests and 6% use ozonotherapy. The most common reason for not using the aforementioned technologies were their high cost and the sufficient effectiveness of raditional methods. There was a correlation between use of a dental laser and CCLAD and size of office, CMCR use and dentists' work time and air abrasion use and gender. Many dentists claim that they will try one of the modern technologies in the future., Conclusions: It can be concluded that Polish dentists tend to use ultrasounds and CCLAD more than any other technology. In the future this may change, so more studies in this topic are needed.

Despite many studies, opinions on the lymphatic system of the teeth are still incompatible. Studies using light and electron microscopy and directly using methods such as a radioisotope (radionuclide) scan and interstitial fluid pressure measurement reported incomplete results. Immunohistochemistry (IHC) plays the main role in investigating presence of the lymphatic system in dental tissues. This method uses labeled antibodies against antigens typical of lymphatic vessels. The use of appropriate staining enables the detection of antigen-antibody reaction products using a light (optical), electron or fluorescence microscope. However, these studies do not show the system of vessels, their histologic structure under physiological conditions and inflammation as well as the lymphangiogenesis process in the dental pulp. Unfortunately, there is a lack of studies associating the presence of lymphatic vessels in the dental pulp with local lymphatic nodes or large vessels outside the tooth. In the scientific and research environment, the evaluation of the lymphatic system of the teeth is problematic because it is quite difficult to clearly distinguish lymphatic vessels from small blood vessels. Despite many indications of the presence of lymphatic vessels in the pulp chamber, this problem remains open and needs further research.

The lungs are a common site of metastases from malignant tumors. Their removal with a minimal but safe tissue margin is essential for the long-term survival of patients. The aim of this study was to evaluate the usefulness of a 1940 nm thulium-doped fiber laser (TDFL) and a 1470 nm diode laser (DL) in a pig model of lung surgery that involved the incision and excision of lung tissue. Histopathological analysis was performed on days 0 and 7 after surgery. Neither TDFL nor DL caused significant perioperative or postoperative bleeding. Histological analysis revealed the presence of carbonized necrotic tissue, mixed fibrin-cellular exudate in the superficial zone of thermal damage and bands of deeper thermal changes. The mean total width of thermal damage on day 0 was 499.46 ± 61.44 and 937.39 ± 109.65 µm for TDFL and DL, respectively. On day 7, cell activation and repair processes were visible. The total width of thermal damage was 2615.74 ± 487.17 µm for TDFL vs. 6500.34 ±1118.02 µm for DL. The superficial zone of thermal damage was narrower for TDFL on both days 0 and 7. The results confirm the effectiveness of both types of laser in cutting and providing hemostasis in the lungs. TDFL caused less thermal damage to the lung parenchyma than DL.

In recent years, nanomaterials have become increasingly present in medicine, especially in dentistry. Their characteristics are proving to be very useful in clinical cases. Due to the intense research in the field of biomaterials and nanotechnology, the efficacy and possibilities of dental procedures have immensely expanded over the years. The nano size of materials allows them to exhibit properties not present in their larger-in-scale counterparts. The medical procedures in endodontics are time-consuming and mostly require several visits to be able to achieve the proper result. In this field of dentistry, there are still major issues about the removal of the mostly bacterial infection from the dental root canals. It has been confirmed that nanoparticles are much more efficient than traditional materials and appear to have superior properties when it comes to surface chemistry and bonding. Their unique antibacterial properties are also promising features in every medical procedure, especially in endodontics. High versatility of use of nanomaterials makes them a powerful tool in dental clinics, in a plethora of endodontic procedures, including pulp regeneration, drug delivery, root repair, disinfection, obturation and canal filling. This study focuses on summing up the current knowledge about the utility of nanomaterials in endodontics, their characteristics, advantages, disadvantages, and provides a number of reasons why research in this field should be continued.

The replacement of affected blood vessels of the polymer material can cause imbalances in the blood haemostatic system. Changes in blood after the implantation of vascular grafts depend not only on the chemical composition but also on the degree of surface wettability. The Dallon ® H unsealed hydrophilic knitted vascular prosthesis double velour was assessed at work and compare with hydrophobic vascular prosthesis Dallon ® . Spectrophotometric studies were performed in the infrared and differential scanning calorimetry, which confirmed the effectiveness of the process of modifying vascular prostheses. Determination of the parameters of coagulation time of blood after contact in vitro with Dallon ® H vascular prosthesis was also carried out. Prolongation of activated thromboplastin time, decreased activity of factor XII, IX and VIII, were observed. The prolonged thrombin and fibrinogen were reduced in the initial period of the experiment. The activity of plasminogen and antithrombin III and protein C were at the level of control value. The observed changes in the values of determined parameters blood coagulation do not exceed the range of referential values for those indexes. The observed changes are the result of considerable blood absorptiveness by the prosthesis of blood vessels and their sealing.

Background: The aim of this study was to evaluate the usefulness of a thulium-doped fiber laser and a diode laser in zero ischemia kidney surgery, by carrying out a comparative study in a pig model., Material and Methods: Research was carried out on 12 pigs weighing 30 kg each. A thulium-doped fiber laser (TDFL) and a diode laser (DL) operating at wavelengths of 1940 and 1470 nm, respectively, were used. The cut sites were assessed both macroscopically and microscopically. The zone of thermal damage visible in the histopathological preparations was divided into superficial and total areas., Results: During partial nephrectomy, moderate to minimal bleeding was observed, which did not require additional hemostatic measures. All animals survived the procedure. On day 0, the total thermal damage depth was 837.8 µm for the TDFL and 1175.0 µm for the DL. On day 7, the depths were 1556.2 and 2301.7 µm, respectively. On day 14, the overall thermal damage depth for the DL was the greatest (6800 µm). The width of the superficial zone was significantly reduced on days 7 and 14 after TDFL application., Conclusion: Both lasers are suitable for partial wedge nephrectomy without ischemia in pigs. The TDFL produced similar or better hemostasis than the DL, with a smaller zone of thermal damage and, therefore, seems more suitable for application in human medicine.

The aim of this review article is to present various material groups, including ceramics, composites and hybrid materials, currently utilized in the field of CAD/CAM. The described technology is amongst the most important in modern prosthetics. Materials that are applicable in this technique are constantly tested, evaluated and improved. Nowadays, research on dental materials is carried out in order to meet the increasing demand on highly aesthetic and functional indirect restorations. Recent studies present the long-term clinical success of restorations made with the help of both ceramic and composite materials in the CAD/CAM method. However, new materials are developed and introduced that do not have long-term in vivo observations. We can outline a monolithic polymer-infiltrated ceramic network and zirconia teeth support that show promising results to date but require further assessment. The materials will be compared with regard to their mechanical and clinical properties, purpose, advantages and limitations.

Sclerotherapy is the chemical occlusion of vessels using an intravenous injection of a liquid or foamed sclerosing agent that is used in the therapy of blood and lymphatic vessels malformations in the young, and for spider veins, smaller varicose veins, hemorrhoids and hydroceles in adults. This study aimed to assess the effectiveness of mechanosclerotherapy of venous veins with a new device-Flebogrif ® -based on an animal model. The experiment was performed on nine Polish Merino sheep weighing 40-50 kilograms. The animals were anesthetized intravenously. The material was divided into three groups: two experimental (1 and 2) and control (3) group. The first experimental group was treated with the use of Flebogrif ® and a sclerosant simultaneously, while only Flebogrif ® was used in the second experimental group. Flebogrif ® was applied into the lateral saphenous vein of both pelvic limbs. The vessel wall thickness was estimated at four points of the histological image in mm (V1, V2, V3, V4). For one month, the animals were euthanized, and the occlusion rate of the treated veins and changes in the vein wall were determined. Histological slides were analyzed under a light microscope and histometry of the vein wall was performed. The Shapiro-Wilk test and the quantity of the investigated parameter groups allowed for using a non-parametric method at four points to compare thickness measurements (the Mann-Whitney test), with p < 0.05. The Mann-Whitney test indicated statistically significant differences between both experimental groups. The results obtained from morphometrical and histological analysis showed better results in the first experimental group than those of the second experimental group. Finally, statistical analysis revealed significant differences between the both the experimental group and control group in morphological analysis. The achieved results allowed us to conclude that the simultaneous use of Flebogrif ® and a sclerosant yielded better results of vein lumen reduction than the use of Flebogrif ® alone.

Nanotechnology has gained importance in recent years due to its ability to enhance material properties, including antimicrobial characteristics. Nanotechnology is applicable in various aspects of orthodontics. This scientific work focuses on the concept of nanotechnology and its applications in the field of orthodontics, including, among others, enhancement of antimicrobial characteristics of orthodontic resins, leading to reduction of enamel demineralization or control of friction force during orthodontic movement. The latter one enables effective orthodontic treatment while using less force. Emphasis is put on antimicrobial and mechanical characteristics of nanomaterials during orthodontic treatment. The manuscript sums up the current knowledge about nanomaterials' influence on orthodontic appliances.

This review is an attempt to summarize current research on ozone, titanium dioxide (TiO 2 ), silver (Ag), copper oxide CuO and platinum (Pt) nanoparticles (NPs). These agents can be used in various fields of dentistry such as conservative dentistry, endodontic, prosthetic or dental surgery. Nanotechnology and ozone can facilitate the dentist's work by providing antimicrobial properties to dental materials or ensuring a decontaminated work area. However, the high potential of these agents for use in medicine should be confirmed in further research due to possible side effects, especially in long duration of observation so that the best way to apply them can be obtained.

Background: Novel materials used for dentin hypersensitivity (DH) treatment, including hydroxyapatite-based desensitizers, are not only effective in occluding dentinal tubules, but are also biocompatible and non-toxic. A newly formulated desensitizer containing hydroxyapatite was evaluated in comparison to commercially available desensitizers., Objectives: To compare the occluding efficacy and durability of 3 commercially available desensitizing agents with a pharmaceutical composition developed by the authors based on hydroxyapatite (HAp)., Material and Methods: For the experiment, 40 disc-shaped dentin specimens (5 mm thick) were obtained from extracted human teeth. Each disc was divided into 4 sections, so that each desensitizing agent could be applied to each specimen and prepared for further evaluation in most homogenous conditions. The chemical composition of the dentin surfaces was analyzed using scanning electron microscopy (SEM) equipped with an energy-dispersive X-ray spectroscope (EDS), Fourier-transform infrared (FTIR) and Raman spectra techniques. The specimens were immersed in an artificial saliva solution for 24 h, 48 h and 7 days to assess the durability of the layers and the tubule-obliteration effectiveness. Data analysis was performed using Student's t-test with an average value of normal distribution at an unknown variance with a standard deviation (SD) of σ-0.4., Results: All the test groups showed some degree of dentinal tubule occlusion or a covering layer, but the HAp-based composition proved to be the longest-lasting. It was concluded that the developed pharmaceutical composition creates a coating on the dentin surface built of hydroxyapatite crystals sized 10-20 μm, which are likely to constitute a reservoir of calcium and phosphate ions, as well as smaller crystals (0.2-0.3 μm) that occlude dentinal tubules., Conclusions: The composition containing biocompatible hydroxyapatite effectively occluded dentinal tubules and therefore exhibits a potential for reducing the pain and discomfort caused by dentin hypersensitivity.

The research has been carried out with a focus on the assessment of the antimicrobial efficacy of pure nanohydroxyapatite, Cu 2+ -doped nanohydroxyapatite, ozonated olive oil-loaded nanohydroxyapatite, and Cu 2+ -doped nanohydroxyapatite, respectively. Their potential antimicrobial activity was investigated against Streptococcus mutans, Lactobacillus rhamnosus , and Candida albicans . Among all tested materials, the highest efficacy was observed in terms of ozonated olive oil. The studies were performed using an Ultraviolet-Visible spectrophotometry (UV-Vis), electron microscopy, and statistical methods, by determining the value of Colony-Forming Units (CFU/mL) and Minimal Inhibitory Concentration (MIC).

Background: Recently, the defects of the tooth surface in the cervical region are often restored using composite filling materials. It should meet the needs of the patients regarding esthetics and material stability. The aim of the study was to analyze the tooth root surface at the cervical region after the removal of the composite filling material by means of the Erbium-doped Yttrium Aluminium Garnet (Er: YAG) laser or drill using the scanning electron microscopy (SEM) and fluorescence microscopy., Materials and Methods: For the purposes of this study, 14 premolar teeth ( n = 14) were removed due to orthodontic reasons. The rectangular shape cavities with 3 mm in width and 1.5 mm in height were prepared with a 0.8 mm bur on high-speed contra-angle in the tooth surface just below cemento-enamel junction (CEJ) and filled with the composite material. The composite material was removed with the Er: YAG laser at a power of 3.4 W, energy 170 mJ, frequency 20 Hz, pulse duration 300 μs, tip diameter 0.8 mm, air/fluid cooling 3 mL/s, and time of irradiation: 6 sec, at a distance from teeth of 2 mm (G1 group, n = 7) or a high-speed contra-angle bur (G2 group, n = 7). After the removal of composite material, the surfaces of teeth were examined using the scanning electron microscopy (SEM) and fluorescence microscopy., Results: The Er: YAG irradiation allowed to remove completely the composite material from the tooth cavity. The study confirmed, that the ends of collagen fibers were only partially denatured after the Er: YAG laser application., Conclusion: It has been proved that using the Er: YAG laser is an effective and safe method of composite removal for the dentin surface.

Regenerative properties are different in every human tissue. Nowadays, with the increasing popularity of dental implants, bone regenerative procedures called augmentations are sometimes crucial in order to perform a successful dental procedure. Tissue engineering allows for controlled growth of alveolar and periodontal tissues, with use of scaffolds, cells, and signalling molecules. By modulating the patient's tissues, it can positively influence poor integration and healing, resulting in repeated implant surgeries. Application of nanomaterials and stem cells in tissue regeneration is a newly developing field, with great potential for maxillofacial bony defects. Nanostructured scaffolds provide a closer structural support with natural bone, while stem cells allow bony tissue regeneration in places when a certain volume of bone is crucial to perform a successful implantation. Several types of selected nanomaterials and stem cells were discussed in this study. Their use has a high impact on the efficacy of the current and future procedures, which are still challenging for medicine. There are many factors that can influence the regenerative process, while its general complexity makes the whole process even harder to control. The aim of this study was to evaluate the effectiveness and advantage of both stem cells and nanomaterials in order to better understand their function in regeneration of bone tissue in oral cavity.

Partial and total splenectomies are associated with a high risk of substantial blood loss. Lasers operating at wavelengths strongly absorbed by water have the potential to improve hemostasis and cut while providing a narrow zone of thermal damage. The aim of this study is to compare a thulium-doped fiber laser (TDFL) emitting a wavelength of 1940 nm and a diode laser (DL) operating at 1470 nm for spleen surgery in a pig model. A partial splenectomy and spleen incisions were made in 12 animals using the two laser devices. The hemostasis was evaluated visually during surgeries. Post-mortem and histopathological evaluations were done on days 0, 7, and 14 following surgery. Neither TDFL nor DL caused bleeding on day 0 or delayed bleeding. On day 14, pale streaks at the site of incision were slightly wider after cutting with DL than with TDFL. Histological analysis revealed a carbonized zone with exudation and a deeper zone of thermal tissue damage on day 0. The width of the thermal changes was 655.26 ± 107.70 μm for TDFL and 1413.37 ± 111.85 μm for DL. On day 7, a proliferation of fibroblasts and splenocytes was visible, as well as a formation of multinucleated giant cells adjacent to the residues of carbonization. The zone of thermal damage was broader for DL (1157.5 ± 262.77 μm) than for TDFL (682.22 ± 116.58 μm). On day 14, cutting sites were filled with connective and granulation tissues with the residues of carbonization. The zone of thermal damage was narrower for TDFL (761.65 ± 34.3 μm) than for DL (1609.82 ± 202.22 μm). Thus, both lasers are efficient in spleen surgery, providing good hemostasis. However, TDFL produces a narrower zone of thermal damage, which suggests its better efficiency for spleen surgery, especially when performing more precise procedures., Competing Interests: The authors declare no conflicts of interest.

Purpose: The present research aimed to determine whether and how the aluminium chloride - based materials affect the cell line of the bacterial line and fungi., Methods: Cytotoxicity of haemostatic astringents: Alustat (liquid), Alustat (gel), Alustat (foam), Alustin, Hemostat, Racestyptine and Traxodent containing AlCl3 was conducted on L929 cell line with the use of MTT and SRB assays. The antimicrobial activity (CFU and MIC) against C. albicans, S. mutans, L. rhamnosus was determined., Results: In the MTT results, cell viability for all agents were very low. In SRB, the lowest cytotoxicity was demonstrated for Hemostat and Alustat (foam), Traxodent and Racestyptine. Total reduction of the CFU of S. mutans was observed. Alustat (gel) and Alustat (liquid) completely inhibited the growth of C. albicans, S. mutans and L. rhamnosus., Conclusions: The viability of L929 cells obtained in the SRB assay is more reliable than that obtained in the MTT assay, in the case of gingival haemostatic agents.

In the article has been presented an analysis of susceptibility of selected dental materials, made in the CAD/CAM technology. The morphology and structural properties of selected dental materials and their composites were determined by using XRPD (X-ray powder diffraction) techniques, as well as the IR (infrared) spectroscopy. Moreover, an adhesion as well as development of biofilm by oral microorganisms has been studied. It has been shown that a degree of the biofilm development on the tested dental materials depended on microorganism genus and species. Streptococcus mutans has demonstrated the best adhesion to the tested materials in comparison with Candida albicans and Lactobacillus rhamnosus . However, the sintered materials such as IPS e.max® and the polished IPS e.max® have showed the best "anti-adhesive properties" in relation to S. mutans and L. rhamnosus that have not formed the biofilm on the polished IPS e.max® sample. Furthermore, S. mutans have not formed the biofilm on both surfaces. On the contrary to S. mutans and L. rhamnosus , C. albicans has demonstrated the adhesive properties in relation to the above-mentioned surfaces. Moreover, in contrast to S. mutans and C. albicans , L. rhamnosus has not formed the biofilm on the polished IPS Empress material.

In spite of intensively conducted research allowing for the development of more and more advanced wound dressing materials, there is still a need for dressings that stimulate not only reparative and regenerative processes, but also have a positive effect on infected and/or difficult-to-heal wounds. Porous dressing materials based on butyric-acetic chitin co-polyester containing 90% of butyryl and 10% of acetyl groups (BAC 90/10) can also be included in the group mentioned above. Two types of dressings were obtained by the salt leaching method, i.e. a porous sponge Medisorb R and Medisorb Ag with an antibacterial additive. The aim of the study was to evaluate biological effects of porous Medisorb R and Medisorb Ag dressings under in vitro and in vivo conditions. In an in vitro biodegradation test, no mass loss of Medisorb R dressing was observed within 14 days of incubation in physiological fluids at 37 °C. However, on the basis of the FTIR (Fourier Transform Infrared Spectroscopy) tests, surface degradation of Medisorb R dressing was observed. Additionally, the antibacterial activity of the porous Medisorb Ag dressing containing microsilver as an antibacterial additive was confirmed. The in vivo studies included inflammatory activity, skin irritation and sensitisation tests, as well an assessment of local effect after contact with subcutaneous tissue up to 6 months and skin wounds up to 21 days. In the in vivo tests, the dressings exhibited neither effects of skin irritation nor sensitisation. Under macroscopic examination, in full thickness defects of subcutaneous tissue and skin, the dressings caused wound healing with no inflammation, undergoing the most gradual biodegradation between weeks 4 and 8, and the observed differences were statistically significant. In the histological assessment, a weakened, limited inflammatory process associated with degradation of the material has been observed. The process of skin wound healing under Medisorb R dressing in the early period was accelerated compared to that observed in the control group with a gauze dressing.

In recent years, stem cell therapy has become a very promising and advanced scientific research topic. The development of treatment methods has evoked great expectations. This paper is a review focused on the discovery of different stem cells and the potential therapies based on these cells. The genesis of stem cells is followed by laboratory steps of controlled stem cell culturing and derivation. Quality control and teratoma formation assays are important procedures in assessing the properties of the stem cells tested. Derivation methods and the utilization of culturing media are crucial to set proper environmental conditions for controlled differentiation. Among many types of stem tissue applications, the use of graphene scaffolds and the potential of extracellular vesicle-based therapies require attention due to their versatility. The review is summarized by challenges that stem cell therapy must overcome to be accepted worldwide. A wide variety of possibilities makes this cutting edge therapy a turning point in modern medicine, providing hope for untreatable diseases.

The purpose of this study was to evaluate the effects of Nd:YAG laser with flat-top handpiece on the in vitro growth of Candida albicans and Streptococcus mutans. The incidence of C. albicans (opportunistic commensal) and S. mutans (facultatively anaerobic) infections is increasing, despite available treatments. Cultures of Streptococcus mutans and Candida albicans were irradiated using Nd:YAG laser (LightWalker, Fotona) with flat-top handpiece (Genova, LightWalker, Fotona) at the following parameters: group G1: 0.25 W, 10 Hz, 15 s, 3 J and group G2: 1 W, 10 Hz, 60s, 59 J. The results were evaluated directly and 24 h after irradiation using a quantitative culture method (estimation of colony-forming units in 1 ml of suspension, cfu/ml), and microscopic analysis with Janus green stain and compared with control group in which laser was not applied. C. albicans was reduced by 20 up to 54% for G1, and for G2 by 10 up to 60% directly after the application. The cfu/ml values for S. mutans decreased by 13% (p = 0.1771) for G1 and 89% (p < 0.0001) for G2. In both test groups 24 h after the application, the number of colony-forming units decreased by 15-46% for G1 and by 15-64% for G2. The arrested cell division, increasing the surface area and increasing the number of metabolically inactive cells, were observed in morphometric analysis. Macroscopic and microscopic analyses revealed a reduction in cell number and a significant decrease of cell metabolism after laser application for both C. albicans and S. mutans.

Aesthetic medicine is a dynamically developing field of medicine and filling techniques are currently an important and widely used procedure in modern therapeutic methods of facial rejuvenation. The aim of the PTMEiAA Recommendation is to improve patient safety, standardize procedures performed in aesthetic medicine and define minimum quality requirements during individual procedures. This is particularly important in the situation where there are more and more reports of the performance of treatments by unauthorized persons in places that do not meet the sanitary and epidemiological requirements to provide health services. The present study concerns the use of fillers in difficult facial areas: around the eye, glabella and temples.

Partial liver resection is a treatment of choice for liver tumors; the range of parenchyma excision varies from a small part of the tissue surrounding the neoplasm up to 70% of the organ. One of the major concerns during liver resection is blood loss. Thulium lasers which are characterized by the length of emission wave corresponding to a peak absorption of water create a new possibility of cutting tissues efficiently with minimal thermal damage and concurrently providing a good hemostasis control. The aim of our study was to evaluate an impact of liver transection with thulium doped fiber laser on an intraoperative bleeding and histopathological changes during postoperative period in swine model. Ten animals were subjected to open surgery partial liver resection and an incision of liver tissue with an all-fiber, diode-pumped, and continuous-wave Tm 3+ -doped fiber laser emitting 37.4 W of output power at ~1.94  μ m wavelength. The macroscopic and histopathological evaluation was performed intraoperatively as well as 7 and 14 days after surgery. Macroscopically almost no bleeding was observed during surgery and no signs of bleeding were stated after 7 and 14 days. Histopathological analysis of the transection margin revealed a thermal damage area ranging in depth from 620.23 ± 23.82  μ m on the day of surgery to 1817.70 ± 211.98  μ m after 7 days. In the samples taken intraoperatively and after 7 days a superficial zone of carbonization was visibly separated from the deeper changes. After 14 days one 765.35 μ m deep zone characterized by a granulation was present. In conclusion, thulium doped fiber laser is efficacious in cutting with a narrow zone of thermal injury and provides a good hemostasis during liver transection, thus being a potential tool for oncotic liver surgery.

Background: Venous insufficiency is still a serious clinical problem. The exact cause and molecular mechanisms of this disease are still unknown. In this study, we try to identify whether there is a difference in the level of trace elements between healthy and pathological veins. Our results show that insufficient veins have different levels of some trace elements: magnesium, calcium, manganese, and silicon compared to control samples. This study could lead to a better understanding of the molecular causes of venous insufficiency and may help to develop better methods of treatment., Objectives: Nowadays, venous diseases are a very common clinical phenomenon. Venous insufficiency is thought to be one of the most common vein diseases. The exact mechanisms of its etiology are still unknown, although from a clinical point of view some risk factors include gender, age, changing hormone levels, heredity, and standing or sitting for long periods. An imbalance in trace elements could also play a crucial role in the development and/or progression of venous insufficiency., Material and Methods: The trace element content in varicose vein walls and in normal vein walls was measured using an inductively coupled plasma-optical emission spectrometer (ICP-OES) after sample mineralization. Statistical analysis (the Mann-Whitney U test and the Friedman ANOVA) was performed to compare insufficient veins to controls (healthy veins)., Results: This study found statistically significant higher magnesium (Mg) ion levels in varicose veins compared to controls (p = 0.0067) and differences close to statistical significance in calcium (Ca), manganese (Mn), and silicon (Si) ion levels., Conclusions: The results obtained could indicate oxidative stress occurring in chronic venous insufficiency as well as free radical neutralization pathways due to superoxide dismutase (SOD) activity with Mg, Mn and copper (Cu) ion involvement. Our results are consistent with literature data and are preliminary in nature.

In response to the need for implant materials characterized by high biocompatibility a new type of nanostructured Ti6Al7Nb implants for osseous tissue regeneration have been fabricated. The nanostructured cylindrical implants were manufactured in accordance with 3D CAD data using the Selective Laser Melting (SLM) method. Implants were subjected to chemical polishing using a mixture of nitric acid and fluoride (test group) as well as cleaned in distilled water and isopropyl alcohol (control group). The structural and morphological properties of the obtained samples were determined by using XRD (X-ray powder diffraction), TEM (transmission electron microscopy) and SEM (scanning electron microscopy) techniques. The particle size was verified and calculated by Rietveld method to be in the range of 25-90 nm. In the present study, experimental in vivo tests concerning implants fabricated from a nanostructured Ti6Al7Nb alloy, which may substitute bone tissue, were discussed in detail. The control group and test group were used in the study. The animal model was New Zealand rabbit. The implants were implanted into skull fornix and observed after 1, 2 and 3 months. The results of macroscopic and microscopic analysis proved better osseointegration of chemically modified implants., Competing Interests: The authors declare that there is no conflict of interests regarding the publication of this paper., (This journal is © The Royal Society of Chemistry.)

In response to the demand for new implant materials characterized by high biocompatibility and bioresorption, two prototypes of fibrous nanocomposite implants for osseous tissue regeneration made of a newly developed blend of poly(l-lactide- co -glycolide) (PLGA) and syntheticpoly([ R,S ]-3-hydroxybutyrate), PLGA/PHB, have been developed and fabricated. Afibre-forming copolymer of glycolide and l-lactide (PLGA) was obtained by a unique method of synthesis carried out in blocksusing Zr(AcAc)₄ as an initiator. The prototypes of the implants are composed of three layers of PLGA or PLGA/PHB, nonwoven fabrics with a pore structure designed to provide the best conditions for the cell proliferation. The bioactivity of the proposed implants has been imparted by introducing a hydroxyapatite material and IGF1, a growth factor. The developed prototypes of implants have been subjected to a set of in vitro and in vivobiocompatibility tests: in vitro cytotoxic effect, in vitro genotoxicity and systemic toxicity. Rabbitsshowed no signs of negative reactionafter implantation of the experimental implant prototypes., Competing Interests: The authors declare no conflict of interest.

A bstracts: The aim of the study was to evaluate the biocompatibility and bioactivity of two new prototype implants for bone tissue regeneration made from biodegradable fibrous materials. The first is a newly developed poly(l-lactide-co-glycolide), (PLGA), and the second is a blend of PLGA with synthetic poly([R,S]-3-hydroxybutyrate) (PLGA/PHB). The implant prototypes comprise PLGA or PLGA/PHB nonwoven fabrics with designed pore structures to create the best conditions for cell proliferation. The bioactivity of the proposed implants was enhanced by introducing a hydroxyapatite material and a biologically active agent, namely, growth factor IGF1, encapsulated in calcium alginate microspheres. To assess the biocompatibility and bioactivity, allergenic tests and an assessment of the local reaction of bone tissue after implantation were performed. Comparative studies of local tissue response after implantation into trochanters for a period of 12 months were performed on New Zealand rabbits. Based on the results of the in vivo evaluation of the allergenic effects and the local tissue reaction 12 months after implantation, it was concluded that the two implant prototypes, PLGA + IGF1 and PLGA/PHB + IGF1, were characterized by high biocompatibility with the soft and bone tissues of the tested animals., Competing Interests: The authors declare no conflicts of interest.

Biomaterials are substances manufactured for medical purposes in direct contact with the tissues of organisms. Prior to their use, they are tested to determine their usefulness and safety of application. Hydroxyapatites are used in medicine as a bony complement because of their similarity to the natural apatite therein. Thanks to their bioactivity, biocompatibility, stability and non-toxicity hydroxyapatite are the most commonly used materials in osteoimplantology. The use of materials at the nanoscale in medicine or biology may carry the risk of undesirable effects. The aim of the study was to evaluate the cytotoxic effect of high-temperature annealed nanohydroxyapatites on the L929 murine fibroblasts. Nanohydroxyapatites in powder form were obtained by the wet chemistry method: in the temperature range of 800-1000 °C and used for the study. Based on performed studies evaluating the morphology and fibroblast viability, it was found that nanohydroxyapatites show no cytotoxic effects on the L929 cell line., Competing Interests: The authors declare that there are no conflicts of interest regarding the publication of this paper.

Purpose: For many years research has been conducted on the development of resorbable, polymer, haemostatic materials designed to provide first aid and preliminary protection of injuries. The biological properties in vitro of a dressing in powder form called Hemoguard are expected to provide the ability to instantaneously stem bleeding with safe conditions of use. The aim of the study was to evaluate the haemostatic properties of a model of dressing based on micro- and nanofibrids of the chitosan, sodium/calcium alginate and/or carboxymethylcellulose complex. Dressings were prepared by spray-drying and freeze-drying., Methods: Human whole blood was subjected to timed contact with the haemostatic dressing model. Haemolytic action was determined by assaying the degree of haemolysis and evaluating blood cell morphology. Haemostatic action was determined on the basis of selected parameters of plasmatic clotting systems., Results: Dressings prepared by freeze-drying activated the coagulation system. The haemolytic index, plasma haemoglobin concentration values and blood cell morphological shapes were normal. Dressings prepared by spray-drying significantly activated coagulation. Activation of the coagulation process was evidenced by shorter clotting time of the plasma coagulation system and a longer process of clot formation. The dressing was associated with an increased haemolytic index and higher plasma haemoglobin concentration. The morphological shape of blood cells changed., Conclusions: The model of multi-resorbable wound dressings has haemostatic properties. The materials activate the clotting process more quickly than a single-dressing model. Increased activity was found for dressings prepared by spray-drying.

Purpose: This paper reports on the results of investigations on the blood response to the modified of surfaces titanium alloys., Methods: To enhance biocompatibility of the Ti-13Nb-13Zr alloy, anodisation was performed at 80 and 150 V. The oxidation process was carried out in a solution containing 4 mol dm-3 H3PO4 and 0.59 mol dm-3 Ca(H2PO2)2., Results: The haemolytic activity of the titanium alloy surface was not altered much by the anodisation. The obtained values of the percentage of haemolysis were well below the levels required for the materials intended for blood contact. The clotting time of the blood was similar for the as-ground sample and the sample anodised at 80 V. For the sample anodised at 150 V the clotting time was shorter. The differences between these samples were observed in partial thromboplastin time after activation, prothrombin time and thrombin time, after 24 h. Extracts taken from the samples were not toxic towards the L-929 mouse fibroblast cells., Conclusions: The proposed treatment might be appropriate for the preparation of modified Ti-13Nb-13Zr surfaces intended for bone reconstruction or cardiovascular implants depending on process parameters.