Search

We propose and demonstrate a compact and simple vector bending sensor capable of distinguishing any direction and amplitude with high accuracy. The sensor consists of a short segment of asymmetric multicore fiber (MCF) fusion spliced to a standard single mode fiber. The reflection spectrum of such a structure shifts and shrinks in specific manners depending on the direction in which the MCF is bent. By monitoring simultaneously wavelength shift and light power variations, the amplitude and bend direction of the MCF can be unmistakably measured in any orientation, from 0{\deg} to 360{\deg}. The bending sensor proposed here is highly sensitive even for small bending angles (below 1{\deg}).

In this paper, we report on a multicore fiber-based (MCF) temperature sensor that operates in a wide thermal range and that is robustly packaged to withstand harsh environments. To develop the sensor, the fundamentals concerning the effect of temperature on such fibers have been analyzed in detail to predict the most temperature sensitive MCF geometry. Thanks to it, the device, which operates in reflection mode and consists of a short segment of strongly coupled MCF fusion spliced to a standard single mode fiber, shows higher sensitivity than other devices with identical configuration. Regarding its packaging, it consists of an inner ceramic and two outer metallic tubes to provide rigidity and protection against impacts or dirt. The device was calibrated for a thermal range from 25 C to 900 C and a K-type thermocouple was used as reference. Our results suggest that the manufactured optical thermometer is as accurate as the electronic one, reaching a sensitivity up to 29.426 pm/C with the advantage of being passive, compact and easy to fabricate and interrogate. Therefore, we believe this device is appealing for industrial applications that require highly sensitive temperature sensing in very demanding environments, and that the analysis included in this work could be analogously applied to develop sensitivity-optimized devices for other parameters of interest.

The present work deals with a curvature sensor that consists of two segments of asymmetric multicore fiber (MCF) fusion spliced with standard single mode fiber (SMF). The MCF comprises three strongly coupled cores; one of such cores is at the geometrical center of the MCF. The two segments of MCF are short, have different lengths (less than 2 cm each), and are rotated 180 degrees with respect to each other. The fabrication of the sensor was carried out with a fusion splicing machine that has the means for rotating optical fibers. It is demonstrated that the sensor behaves as two SMF-MCF-SMF structures in series, and consequently, it has enhanced sensitivity. The device proposed here can be used to sense the direction and amplitude of curvature by monitoring either wavelength shifts or intensity changes. In the latter case, high curvature sensitivity was observed. The device can also be used for the development of other highly sensitive sensors to monitor, for example, vibrations, force, pressure, or any other parameter that induces periodic or local curvature or bending to the MCF segments.

We report on a compact, highly sensitive all-fiber accelerometer suitable for low frequency and low amplitude vibration sensing. The sensing elements in the device are two short segments of strongly coupled asymmetric multicore fiber (MCF) fusion spliced at 180{\deg} with respect to each other. Such segments of MCF are sandwiched between standard single mode fibers. The reflection spectrum of the device exhibits a narrow spectrum whose height and position in wavelength changes when it is subjected to vibrations. The interrogation of the accelerometer was carried out by a spectrometer and a photodetector to measure simultaneously wavelength shift and light power variations. The device was subjected to a wide range of vibration frequencies, from 1 mHz to 30 Hz, and accelerations from 0.76 mg to 29.64 mg, and performed linearly, with a sensitivity of 2.213 nW/mg. Therefore, we believe the accelerometer reported here may represent an alternative to existing electronic and optical accelerometers, especially for low frequency and amplitude vibrations, thanks to its compactness, simplicity, cost-effectiveness, implementation easiness and high sensitivity.

Supercontinuum (SC) generation based on ultrashort pulse compression constitutes one of the most promising technologies towards an ultra-wide bandwidth, high-brightness and spatially coherent light sources for applications such as spectroscopy and microscopy. Here, multi-octave SC generation in a gas-filled hollow-core antiresonant fiber (HC-ARF) is reported spanning from 200 nm in the deep ultraviolet (DUV) to 4000 nm in the mid-infrared (mid-IR). A measured average output power of 5 mW was obtained by pumping at the center wavelength of the first anti-resonance transmission window (2460 nm) with ~100 fs pulses and an injected pulse energy of ~7-8 {\mu}J. The mechanism behind the extreme spectral broadening relies upon intense soliton-plasma nonlinear dynamics which leads to efficient soliton self-compression and phase-matched dispersive wave (DW) emission in the DUV region. The strongest DW is observed at 275 nm having an estimated pulse energy of 1.42 {\mu}J, corresponding to 28.4 % of the total output energy. Furthermore, the effect of changing the pump pulse energy and gas pressure on the nonlinear dynamics and their direct impact on SC generation was investigated. The current work paves a new way towards novel investigations of gas-based ultrafast nonlinear optics in the emerging mid-IR spectral regime.

We describe a technique for surface and sub-surface micro-machining of glass substrates using tightly focused femtosecond laser pulses at a wavelength of 1660 nm. Although silicate glass is normally transparent at this wavelength, the extremely high intensity of the focused beam causes multi-photon absorption, resulting in localized ablation of the glass substrate. Ablation is strictly confined to the vicinity of focus, leaving the rest of the substrate unaffected. We exploit this phenomenon to drill a micro-hole through a thin vertical wall that separates two adjacent pits machined by the same laser in a glass plate. A salient feature of pulsed laser micro-machining, therefore, is its ability to drill sub-surface tunnels and canals into glass substrates, a process that requires multiple steps in standard lithography. To demonstrate a potential application of this micro-machining technique, we have fabricated simple micro-fluidic structures on a glass plate. To prevent the evaporation of liquids in open micro-channels and micro-chambers thus fabricated requires a cover plate that seals the device by making point-to-point contact with the flat surface of the substrate. This point-to-point contacting is essential if the fluids are to remain confined within their various channels and chambers on the chip, without leaking into neighboring regions. Methods of protecting and sealing the micro-machined structures for microfluidic applications are also discussed., Comment: 14 pages, 8 figures, 12 references