Search

Abstracts. A high-temperature molten salt natural convection loop was designed and manufactured for chloride-based salts. NaCl-MgCl2 salt was prepared and injected into the loop. Corrosion coupons composed of SS304, SS316L, and high-Ni alloys were also prepared as candidate structural materials for molten chloride salt reactors. After a corrosion experiment was conducted for 500 h, the salt was drained from the loop to the drain tank; inductively coupled plasma optical emission spectroscopy was used to investigate metal dissolution from the materials into the salt. The corroded materials were analyzed using scanning electron microscopy and energy-dispersive X-ray spectroscopy to calculate the corrosion rate. Materials exposed to NaCl-MgCl2 molten salt showed varying levels of corrosion resistance. The high-Ni alloy demonstrated the highest resistance, followed by SS316L and SS304. Furthermore, corrosion products were observed to migrate along the molten salt through natural convection, eventually depositing onto the surface of the high-Ni alloy in the cold leg of the loop. [ABSTRACT FROM AUTHOR]

Abstracts. A high-temperature molten salt natural convection loop was designed and manufactured for chloride-based salts. NaCl-MgCl2 salt was prepared and injected into the loop. Corrosion coupons composed of SS304, SS316L, and high-Ni alloys were also prepared as candidate structural materials for molten chloride salt reactors. After a corrosion experiment was conducted for 500 h, the salt was drained from the loop to the drain tank; inductively coupled plasma optical emission spectroscopy was used to investigate metal dissolution from the materials into the salt. The corroded materials were analyzed using scanning electron microscopy and energy-dispersive X-ray spectroscopy to calculate the corrosion rate. Materials exposed to NaCl-MgCl2 molten salt showed varying levels of corrosion resistance. The high-Ni alloy demonstrated the highest resistance, followed by SS316L and SS304. Furthermore, corrosion products were observed to migrate along the molten salt through natural convection, eventually depositing onto the surface of the high-Ni alloy in the cold leg of the loop. [ABSTRACT FROM AUTHOR]

A complementary metal oxide semiconductor (CMOS) voltage‐controlled oscillator (VCO) using a tail current source modulated with the output frequency is presented to achieve low phase noise with low power consumption at the K‐band. Differentially modulated current sources, which reduce flicker noise by the feedback of the VCO outputs, contribute to an overall reduction in the phase noise of the VCO using the electromagnetic‐based fully symmetrical design. The proposed LC VCO with a 3‐bit switched capacitor bank for a wide tuning range was fabricated on the size of 0.4 × 0.57 mm2 using a 65‐nm CMOS process. The measurement results of the proposed VCO showed a frequency tuning range from 22.57 to 25.3 GHz, and a phase noise of −108.48 dBc/Hz at a 1‐MHz offset frequency with a power consumption of 8.27 mW at a supply voltage of 1.2 V. The calculated figure of merit (FoM) and FoM with the tuning range were −186.48 and −187.67 dBc/Hz, respectively. [ABSTRACT FROM AUTHOR]

Canine natural killer (NK) cells are large, granular lymphocytes that are neither B lymphocytes nor T lymphocytes. However, it has been reported that canine NK cells share some of the phenotypic characteristics of T lymphocytes, such as CD3 and CD5. Studies are needed to assess the safety of canine NK cells for immunotherapy, especially because the safety of using allogeneic NK cells as an immunotherapy for dogs has yet to be shown. In this study, the safety of cultured canine NK cells was assessed using a xenogeneic mouse model of graft‐versus‐host disease (GVHD). Mice were injected with either canine peripheral blood mononuclear cells (PBMCs) or cultured NK cells for 2 or 3 weeks. Data were then collected on changes in mice body weights, disease severity scores, and survival rates. Histopathological and immunohistochemical evaluations were also performed. All mice injected with canine PBMCs died within 45 days after injection. Severe clinical signs were caused by GVHD. The histopathological and immunohistochemical evaluations showed that mice injected with canine PBMCs had multiple lesions, including necrosis in their lungs, livers, kidneys, and stomachs, and the injected cells were present around the lesions. By contrast, no mice injected with cultured NK cells without removing the CD3+TCR– cells exhibited any clinical abnormalities. Moreover, they all survived the 90‐day experimental period without exhibiting any histopathological changes. Accordingly, the results of this study suggest that canine NK cells do not cause significant side effects such as GVHD and allogeneic NK cells can safely be used for cancer immunotherapy in dogs. [ABSTRACT FROM AUTHOR]